Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  B1637/82  Lost Communication with Rear Airbag Sensor LH  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  B1648/82  Side Satellite Sensor Bus LH Initialization Incomplete  B167B/82  Lost Communication with Front Door Pressure Sensor LH  B167C/82  Front Door Pressure Sensor LH Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.

The door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1627/82 Lost communication with Side Airbag Sensor LH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1637/82 Lost Communication with Rear Airbag Sensor LH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1647/82 Lost Communication with Side Satellite Sensor Bus LH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1648/82 Side Satellite Sensor Bus LH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B167B/82 Lost Communication with Front Door Pressure Sensor LH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B167C/82 Front Door Pressure Sensor LH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 1 side airbag sensor LH malfunction

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 1 side airbag sensor LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B1627/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1628/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1637/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1638/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1647/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1648/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B167B/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B167C/82):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor LH malfunction - - - - ○ - - -
No. 2 side airbag sensor LH malfunction - - - - - ○ - -
Door side airbag sensor LH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C238366E98
3.427,4.667 3.969,5.083 0.542,0.417 10 false M15 0.542,2.781 1.667,3.344 1.125,0.563 10 false No. 1 Side Airbag Sensor LH 0.552,4.823 2.417,5.302 1.865,0.479 10 false Door Side Airbag Sensor LH 5.521,4.844 7.156,5.146 1.635,0.302 10 false Airbag Sensor Assembly 5.51,4.688 6.573,4.896 1.063,0.208 10 false M2*1, M1*2 1.156,0.521 1.958,1.083 0.802,0.563 10 false BBL+ 1.594,0.438 2.063,0.938 0.469,0.5 10 false 4 1.177,1.104 1.813,1.604 0.635,0.5 10 false BBL- 4.885,0.438 5.865,0.823 0.979,0.385 10 false 8*1, 24*2 4.823,1 5.688,1.438 0.865,0.438 10 false 15*1, 23*2 1.594,1.01 1.948,1.448 0.354,0.438 10 false 3 1.146,3.792 1.948,4.427 0.802,0.635 10 false BDL+ 2.406,3.594 2.854,4.198 0.448,0.604 10 false 22 1.167,4.354 1.792,4.833 0.625,0.479 10 false BDL- 2.406,4.146 2.76,4.563 0.354,0.417 10 false 40 2.365,3.792 3.021,4.354 0.656,0.563 10 false JM1 2.365,4.333 2.917,4.854 0.552,0.521 10 false JM1 0.552,4.667 1.146,5.073 0.594,0.406 10 false J5 3.427,4.823 4.531,5.25 1.104,0.427 10 false No. 2 Side Airbag Sensor LH 0.531,2.615 1.104,3.083 0.573,0.469 10 false M13 3.469,3.802 4.063,4.292 0.594,0.49 10 false BDL+ 3.469,4.333 4.01,4.865 0.542,0.531 10 false BDL- 3.479,1.698 4.063,2.146 0.583,0.448 10 false BCL+ 3.469,2.302 4.031,2.729 0.563,0.427 10 false BCL- 1.146,1.688 1.708,2.083 0.563,0.396 10 false BCL+ 1.177,2.302 1.844,2.792 0.667,0.49 10 false BCL- 5.563,0.542 6.135,1 0.573,0.458 10 false BBL+ 5.563,1.115 6.021,1.656 0.458,0.542 10 false BBL- 1.594,1.604 2.063,2.271 0.469,0.667 10 false 1 1.594,2.208 2.083,2.688 0.49,0.479 10 false 2 3.292,1.604 3.75,2.073 0.458,0.469 10 false 4 3.292,2.177 3.875,2.74 0.583,0.563 10 false 3 3.313,3.698 3.771,4.135 0.458,0.438 10 false 1 3.313,4.24 3.802,4.792 0.49,0.552 10 false 2 1.594,3.698 2.021,4.323 0.427,0.625 10 false 2 1.594,4.24 2.021,4.813 0.427,0.573 10 false 1 0.219,5.198 2.969,5.521 2.75,0.323 10 false *1: w/o Dual-stage SRS 0.219,5.5 2.969,5.823 2.75,0.323 10 false *2: w/ Dual-stage SRS

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

·

Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B167B, B167C and 82 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1647, B1648 or 82 is output. A
Current DTC B1628 is output. B
Current DTC B1638 is output. C
Current DTC B167B or B167C is output. D
Current DTC B1627 is output. E
Current DTC B1637 is output. F
Current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B167B, B167C and 82 are not output. G



A

2.CHECK CONNECTORS

B

22.CHECK HISTORY DTC

C

42.CHECK HISTORY DTC

D

51.CHECK CONNECTORS

E

62.CHECK NO. 1 SIDE AIRBAG SENSOR LH

F

63.CHECK NO. 2 SIDE AIRBAG SENSOR LH

G

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK FLOOR WIRE (OPEN)
a.

w/o Dual-stage SRS

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

w/ Dual-stage SRS

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



C348452C03
0.76,2.885 1.177,3.135 0.417,0.25 1.26,0.385 1.563,0.594 0.302,0.208 4.667,0.406 4.979,0.625 0.313,0.219 4.375,2.844 4.792,3.094 0.417,0.25 1.698,1.896 1.698,1.479 1.698,1.479 1.531,1.479 false 5.448,2.188 5.281,2.188 5.281,2.188 5.281,1.854 false 2.094,1.125 2.094,0.958 false 5.802,1.167 5.802,1.031 false 1.656,0.99 2.021,0.552 true 2.49,0.979 2.208,0.76 true 5.458,0.99 5.75,0.75 true 6.167,0.99 5.854,0.75 true 1.51,3.406 1.75,3.031 true 2.115,3.406 1.854,3.042 true 5.104,3.417 5.344,3.042 true 5.698,3.406 5.438,3.042 true 0.542,0.083 1,0.5 0.458,0.417 10 false *A 4.083,0.083 4.542,0.51 0.458,0.427 10 false *B 4.469,1.688 4.875,2.083 0.406,0.396 10 false *1 2.5,1.885 2.938,2.25 0.438,0.365 10 false *2 1.375,1.406 1.688,1.688 0.313,0.281 10 false *3 5.74,1.188 6.135,1.458 0.396,0.271 10 false *4 1.073,0.177 1.448,0.656 0.375,0.479 10 false *a 0.719,2.625 1.094,2.948 0.375,0.323 10 false *b 0.854,1.865 1.542,2.323 0.688,0.458 10 false *1 6.125,1.979 6.563,2.344 0.438,0.365 10 false *2 5.479,2.104 5.938,2.406 0.458,0.302 10 false *3 2.021,1.135 2.385,1.479 0.365,0.344 10 false *4 4.552,0.167 4.927,0.646 0.375,0.479 10 false *a 4.302,2.615 4.677,2.938 0.375,0.323 10 false *b 0.833,2.938 1.208,3.26 0.375,0.323 10 false M13 4.458,2.885 4.833,3.208 0.375,0.323 10 false M13 1.323,0.417 1.698,0.74 0.375,0.323 10 false M2 4.74,0.438 5.115,0.76 0.375,0.323 10 false M1 1.5,1 1.875,1.323 0.375,0.323 10 false BBL+ 2.375,1 2.75,1.323 0.375,0.323 10 false BBL- 6.042,1 6.417,1.323 0.375,0.323 10 false BBL+ 5.313,1 5.688,1.323 0.375,0.323 10 false BBL- 1.365,3.417 1.74,3.74 0.375,0.323 10 false BBL- 2.01,3.417 2.385,3.74 0.375,0.323 10 false BBL+ 5.594,3.417 5.969,3.74 0.375,0.323 10 false BBL+ 4.979,3.417 5.354,3.74 0.375,0.323 10 false BBL- 2.135,1.885 2.573,2.25 0.438,0.365 10 false A 1.854,1.885 2.292,2.25 0.438,0.365 10 false B 1.458,1.885 1.896,2.25 0.438,0.365 10 false C 1.177,1.885 1.615,2.25 0.438,0.365 10 false D 5.719,1.719 6.156,2.083 0.438,0.365 10 false A 5.438,1.719 5.875,2.083 0.438,0.365 10 false B 5.042,1.719 5.479,2.083 0.438,0.365 10 false C 4.76,1.719 5.198,2.083 0.438,0.365 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-4 (BBL+) - M13-3 (BBL-) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.

Measure the resistance according to the value(s) in the table below.

C348453C02
0.844,1.667 1.25,1.917 0.406,0.25 4.417,1.677 4.823,1.927 0.406,0.25 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 true 2.24,2.25 1.979,1.865 true 1.625,2.26 1.865,1.865 true 5.823,2.25 5.563,1.865 true 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.927,1.698 1.313,2.063 0.385,0.365 10 false M13 4.49,1.708 4.875,2.073 0.385,0.365 10 false M13 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M13-4 (BBL+) - M13-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.

Connect the cable to the negative (-) auxiliary battery terminal.

C348453C02
0.844,1.667 1.25,1.917 0.406,0.25 4.417,1.677 4.823,1.927 0.406,0.25 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 true 2.24,2.25 1.979,1.865 true 1.625,2.26 1.865,1.865 true 5.823,2.25 5.563,1.865 true 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.927,1.698 1.313,2.063 0.385,0.365 10 false M13 4.49,1.708 4.875,2.073 0.385,0.365 10 false M13 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
- -



b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M13-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M13-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C348453C02
0.844,1.667 1.25,1.917 0.406,0.25 4.417,1.677 4.823,1.927 0.406,0.25 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 true 2.24,2.25 1.979,1.865 true 1.625,2.26 1.865,1.865 true 5.823,2.25 5.563,1.865 true 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.927,1.698 1.313,2.063 0.385,0.365 10 false M13 4.49,1.708 4.875,2.073 0.385,0.365 10 false M13 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M13-4 (BBL+) - Body ground Always 1 MΩ or higher
M13-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
a.
C238392C27
0.469,3.542 0.833,3.792 0.365,0.25 0.844,0.5 1.333,0.75 0.49,0.25 1.823,0.708 1.49,1.031 true 1.948,0.708 2.281,1.031 true 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 true 1.646,3.667 2,4.031 true 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.531,3.573 0.948,3.896 0.417,0.323 10 false M15 0.958,0.542 1.333,0.833 0.375,0.292 10 false M13 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)


Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - M13-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - M13-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT TO B+)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M13-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M13-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - Body ground Always 1 MΩ or higher
M13-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (OPEN)

NG

REPLACE FLOOR WIRE

11.CHECK WIRE HARNESS (OPEN)
a.
C284683C19
0.792,0.573 1.167,0.813 0.375,0.24 0.521,3.625 0.865,3.865 0.344,0.24 2.323,1.073 1.906,0.656 true 1.01,4.156 1.385,3.74 true 2.042,4.167 1.625,3.75 true 1.354,1.083 1.771,0.667 true 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDL+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDL- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDL+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDL- 0.854,0.615 1.271,1.031 0.417,0.417 10 false M15 0.635,3.667 1.052,4.083 0.417,0.417 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - J5-1 (BDL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK WIRE HARNESS (SHORT)

NG

21.CHECK FLOOR WIRE (OPEN)
12.CHECK WIRE HARNESS (SHORT)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - J5-1 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK WIRE HARNESS (SHORT TO B+)

NG

20.CHECK FLOOR WIRE (SHORT)
13.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J5-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
J5-1 (BDL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

19.CHECK FLOOR WIRE (SHORT TO B+)
14.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - Body ground Always 1 MΩ or higher
J5-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK NO. 1 SIDE AIRBAG SENSOR LH

NG

18.CHECK FLOOR WIRE (SHORT TO GROUND)
15.CHECK NO. 1 SIDE AIRBAG SENSOR LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connectors to the No. 2 side airbag sensor LH, door side airbag sensor LH and airbag sensor assembly.


b.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.



A

16.CHECK NO. 2 SIDE AIRBAG SENSOR LH

B

C

16.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor LH


Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

17.CHECK DOOR SIDE AIRBAG SENSOR LH

B

C

17.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor LH


Interchange the door side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

18.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Always 1 MΩ or higher
JM1-40 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

19.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JM1-22 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM1-40 (BDL-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

20.CHECK FLOOR WIRE (SHORT)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (OPEN)
a.
C284681C18
0.823,0.552 1.188,0.802 0.365,0.25 0.458,2.823 0.833,3.042 0.375,0.219 1.781,4.302 1.406,3.771 true 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.323,1.167 1.906,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.302 1.406,3.625 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDL+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDL- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDL+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDL- 0.885,0.594 1.385,0.927 0.5,0.333 10 false M15 0.531,2.854 1.031,3.188 0.5,0.333 10 false JM1
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

22.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1627 is not output. A
History DTC B1627 is output. B



A

23.CHECK CONNECTORS

B

41.CHECK NO. 1 SIDE AIRBAG SENSOR LH
23.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, No. 1 side airbag sensor LH, No. 2 side airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

24.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

24.CHECK FLOOR WIRE (OPEN)
a.

w/o Dual-stage SRS

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

w/ Dual-stage SRS

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



C348452C04
0.76,2.885 1.177,3.135 0.417,0.25 1.26,0.385 1.563,0.594 0.302,0.208 4.667,0.406 4.979,0.625 0.313,0.219 4.375,2.844 4.792,3.094 0.417,0.25 1.698,1.896 1.698,1.479 1.698,1.479 1.531,1.479 false 5.448,2.188 5.281,2.188 5.281,2.188 5.281,1.854 false 2.094,1.125 2.094,0.958 false 5.802,1.167 5.802,1.031 false 1.656,0.99 2.021,0.552 true 2.49,0.979 2.208,0.76 true 5.458,0.99 5.75,0.75 true 6.167,0.99 5.854,0.75 true 1.51,3.406 1.75,3.031 true 2.115,3.406 1.854,3.042 true 5.104,3.417 5.344,3.042 true 5.698,3.406 5.438,3.042 true 0.542,0.083 1,0.5 0.458,0.417 10 false *A 4.083,0.083 4.542,0.51 0.458,0.427 10 false *B 4.469,1.688 4.875,2.083 0.406,0.396 10 false *1 2.5,1.885 2.938,2.25 0.438,0.365 10 false *2 1.375,1.406 1.688,1.688 0.313,0.281 10 false *3 5.74,1.188 6.135,1.458 0.396,0.271 10 false *4 1.073,0.177 1.448,0.656 0.375,0.479 10 false *a 0.719,2.625 1.094,2.948 0.375,0.323 10 false *b 0.854,1.865 1.542,2.323 0.688,0.458 10 false *1 6.125,1.979 6.563,2.344 0.438,0.365 10 false *2 5.479,2.104 5.938,2.406 0.458,0.302 10 false *3 2.021,1.135 2.385,1.479 0.365,0.344 10 false *4 4.552,0.167 4.927,0.646 0.375,0.479 10 false *a 4.302,2.615 4.677,2.938 0.375,0.323 10 false *b 0.833,2.938 1.208,3.26 0.375,0.323 10 false M13 4.458,2.885 4.833,3.208 0.375,0.323 10 false M13 1.323,0.417 1.698,0.74 0.375,0.323 10 false M2 4.74,0.438 5.115,0.76 0.375,0.323 10 false M1 1.5,1 1.875,1.323 0.375,0.323 10 false BBL+ 2.375,1 2.75,1.323 0.375,0.323 10 false BBL- 6.042,1 6.417,1.323 0.375,0.323 10 false BBL+ 5.313,1 5.688,1.323 0.375,0.323 10 false BBL- 1.365,3.417 1.74,3.74 0.375,0.323 10 false BBL- 2.01,3.417 2.385,3.74 0.375,0.323 10 false BBL+ 5.594,3.417 5.969,3.74 0.375,0.323 10 false BBL+ 4.979,3.417 5.354,3.74 0.375,0.323 10 false BBL- 2.135,1.885 2.573,2.25 0.438,0.365 10 false A 1.854,1.885 2.292,2.25 0.438,0.365 10 false B 1.458,1.885 1.896,2.25 0.438,0.365 10 false C 1.177,1.885 1.615,2.25 0.438,0.365 10 false D 5.719,1.719 6.156,2.083 0.438,0.365 10 false A 5.438,1.719 5.875,2.083 0.438,0.365 10 false B 5.042,1.719 5.479,2.083 0.438,0.365 10 false C 4.76,1.719 5.198,2.083 0.438,0.365 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 side airbag sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to No. 1 side airbag sensor LH)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-4 (BBL+) - M13-3 (BBL-) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

25.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

25.CHECK FLOOR WIRE (SHORT)
a.

Measure the resistance according to the value(s) in the table below.

C348453C02
0.844,1.667 1.25,1.917 0.406,0.25 4.417,1.677 4.823,1.927 0.406,0.25 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 true 2.24,2.25 1.979,1.865 true 1.625,2.26 1.865,1.865 true 5.823,2.25 5.563,1.865 true 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.927,1.698 1.313,2.063 0.385,0.365 10 false M13 4.49,1.708 4.875,2.073 0.385,0.365 10 false M13 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M13-4 (BBL+) - M13-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

26.CHECK FLOOR WIRE (SHORT TO B+)
a.

Connect the cable to the negative (-) auxiliary battery terminal.

C348453C02
0.844,1.667 1.25,1.917 0.406,0.25 4.417,1.677 4.823,1.927 0.406,0.25 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 true 2.24,2.25 1.979,1.865 true 1.625,2.26 1.865,1.865 true 5.823,2.25 5.563,1.865 true 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.927,1.698 1.313,2.063 0.385,0.365 10 false M13 4.49,1.708 4.875,2.073 0.385,0.365 10 false M13 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
- -



b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M13-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M13-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

27.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

27.CHECK FLOOR WIRE (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C348453C02
0.844,1.667 1.25,1.917 0.406,0.25 4.417,1.677 4.823,1.927 0.406,0.25 5.448,0.885 5.281,0.885 5.281,0.885 5.281,0.552 false 1.521,0.177 1.688,0.177 1.688,0.177 1.688,0.51 false 5.208,2.26 5.448,1.865 true 2.24,2.25 1.979,1.865 true 1.625,2.26 1.865,1.865 true 5.823,2.25 5.563,1.865 true 0.375,0.063 0.865,0.385 0.49,0.323 10 false *A 3.917,0.094 4.385,0.531 0.469,0.438 10 false *B 0.875,0.479 1.281,0.813 0.406,0.333 10 false *1 2.5,0.5 2.896,0.896 0.396,0.396 10 false *2 0.729,1.427 1.115,1.792 0.385,0.365 10 false *a 4.302,1.438 4.688,1.802 0.385,0.365 10 false *a 4.448,0.406 4.854,0.74 0.406,0.333 10 false *1 6.115,0.667 6.51,1.063 0.396,0.396 10 false *2 1.365,0.094 1.729,0.365 0.365,0.271 10 false *3 5.469,0.802 5.833,1.188 0.365,0.385 10 false *3 0.927,1.698 1.313,2.063 0.385,0.365 10 false M13 4.49,1.708 4.875,2.073 0.385,0.365 10 false M13 2.135,2.25 2.521,2.615 0.385,0.365 10 false BBL+ 1.5,2.25 1.896,2.625 0.396,0.375 10 false BBL- 5.698,2.25 6.083,2.615 0.385,0.365 10 false BBL+ 5.063,2.25 5.448,2.615 0.385,0.365 10 false BBL- 2.135,0.5 2.531,0.896 0.396,0.396 10 false A 1.854,0.5 2.25,0.896 0.396,0.396 10 false B 1.458,0.5 1.854,0.896 0.396,0.396 10 false C 1.177,0.5 1.573,0.896 0.396,0.396 10 false D 5.719,0.406 6.115,0.802 0.396,0.396 10 false A 5.438,0.406 5.833,0.802 0.396,0.396 10 false B 5.031,0.406 5.427,0.802 0.396,0.396 10 false C 4.75,0.406 5.146,0.802 0.396,0.396 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M13-4 (BBL+) - Body ground Always 1 MΩ or higher
M13-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

28.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

28.CHECK FLOOR WIRE (OPEN)
a.
C238392C27
0.469,3.542 0.833,3.792 0.365,0.25 0.844,0.5 1.333,0.75 0.49,0.25 1.823,0.708 1.49,1.031 true 1.948,0.708 2.281,1.031 true 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 true 1.646,3.667 2,4.031 true 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.531,3.573 0.948,3.896 0.417,0.323 10 false M15 0.958,0.542 1.333,0.833 0.375,0.292 10 false M13 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)


Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - M13-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

29.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

29.CHECK FLOOR WIRE (SHORT)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - M13-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

30.CHECK FLOOR WIRE (SHORT TO B+)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M13-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M13-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

31.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

31.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - Body ground Always 1 MΩ or higher
M13-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

32.CHECK WIRE HARNESS (OPEN)

NG

REPLACE FLOOR WIRE

32.CHECK WIRE HARNESS (OPEN)
a.
C284683C19
0.792,0.573 1.167,0.813 0.375,0.24 0.521,3.625 0.865,3.865 0.344,0.24 2.323,1.073 1.906,0.656 true 1.01,4.156 1.385,3.74 true 2.042,4.167 1.625,3.75 true 1.354,1.083 1.771,0.667 true 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDL+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDL- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDL+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDL- 0.854,0.615 1.271,1.031 0.417,0.417 10 false M15 0.635,3.667 1.052,4.083 0.417,0.417 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - J5-1 (BDL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

33.CHECK WIRE HARNESS (SHORT)

NG

40.CHECK FLOOR WIRE (OPEN)
33.CHECK WIRE HARNESS (SHORT)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - J5-1 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

34.CHECK WIRE HARNESS (SHORT TO B+)

NG

39.CHECK FLOOR WIRE (SHORT)
34.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J5-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
J5-1 (BDL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

35.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

38.CHECK FLOOR WIRE (SHORT TO B+)
35.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - Body ground Always 1 MΩ or higher
J5-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

36.CHECK NO. 1 SIDE AIRBAG SENSOR LH

NG

37.CHECK FLOOR WIRE (SHORT TO GROUND)
36.CHECK NO. 1 SIDE AIRBAG SENSOR LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connectors to the No. 2 side airbag sensor LH, door side airbag sensor LH and airbag sensor assembly.


b.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1628 is output. A
DTC B1623 is output. B
DTCs B1623 and B1628 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

37.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Always 1 MΩ or higher
JM1-40 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

38.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JM1-22 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM1-40 (BDL-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

39.CHECK FLOOR WIRE (SHORT)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

40.CHECK FLOOR WIRE (OPEN)
a.
C284681C18
0.823,0.552 1.188,0.802 0.365,0.25 0.458,2.823 0.833,3.042 0.375,0.219 1.781,4.302 1.406,3.771 true 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.323,1.167 1.906,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.302 1.406,3.625 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDL+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDL- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDL+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDL- 0.885,0.594 1.385,0.927 0.5,0.333 10 false M15 0.531,2.854 1.031,3.188 0.5,0.333 10 false JM1
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

41.CHECK NO. 1 SIDE AIRBAG SENSOR LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1627 is output. A
DTC B1622 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

42.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1637 is not output. A
History DTC B1637 is output. B



A

43.CHECK CONNECTORS

B

50.CHECK NO. 2 SIDE AIRBAG SENSOR LH
43.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

44.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

44.CHECK FLOOR WIRE (OPEN)
a.
C238392C27
0.469,3.542 0.833,3.792 0.365,0.25 0.844,0.5 1.333,0.75 0.49,0.25 1.823,0.708 1.49,1.031 true 1.948,0.708 2.281,1.031 true 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 true 1.646,3.667 2,4.031 true 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.531,3.573 0.948,3.896 0.417,0.323 10 false M15 0.958,0.542 1.333,0.833 0.375,0.292 10 false M13 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)


Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - M13-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

45.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

45.CHECK FLOOR WIRE (SHORT)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 side airbag sensor LH
*2 No. 1 Side Airbag Sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - M13-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

46.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

46.CHECK FLOOR WIRE (SHORT TO B+)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 side airbag sensor LH
*2 No. 1 side airbag sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 side airbag sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M13-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M13-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

47.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

47.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C368460C02
1.083,2.26 1.583,2.51 0.5,0.25 1.698,0.75 1.531,0.417 false 1.75,2.833 2.073,2.458 true 2.5,2.833 2.24,2.458 true 0.865,0.74 1.177,0.938 0.313,0.198 10 false *1 2.51,0.75 2.823,0.948 0.313,0.198 10 false *2 1.01,1.885 1.323,2.083 0.313,0.198 10 false *a 1.156,0.75 1.302,0.948 0.146,0.198 10 false D 1.458,0.75 1.604,0.948 0.146,0.198 10 false C 1.917,0.75 2.063,0.948 0.146,0.198 10 false B 2.229,0.74 2.375,0.938 0.146,0.198 10 false A 1.354,0.26 1.667,0.458 0.313,0.198 10 false *3 1.188,2.313 1.583,2.563 0.396,0.25 10 false M13 1.417,2.865 1.896,3.115 0.479,0.25 10 false BCL+ 2.49,2.875 2.969,3.125 0.479,0.25 10 false BCL-
*1 No. 2 side airbag sensor LH
*2 No. 1 side airbag sensor LH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 side airbag sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M13-1 (BCL+) - Body ground Always 1 MΩ or higher
M13-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

48.CHECK NO. 1 SIDE AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

48.CHECK NO. 1 SIDE AIRBAG SENSOR LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the No. 2 side airbag sensor LH.


b.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.



A

49.CHECK NO. 2 SIDE AIRBAG SENSOR LH

B

C

49.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor LH


Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

50.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor LH


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1637 is output. A
DTC B1632 is output. B
DTCs B1632 and B1637 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

51.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the No. 2 side airbag sensor LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the No. 2 side airbag sensor LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

52.CHECK WIRE HARNESS (OPEN)

NG

REPLACE WIRE HARNESS

52.CHECK WIRE HARNESS (OPEN)
a.
C284683C19
0.792,0.573 1.167,0.813 0.375,0.24 0.521,3.625 0.865,3.865 0.344,0.24 2.323,1.073 1.906,0.656 true 1.01,4.156 1.385,3.74 true 2.042,4.167 1.625,3.75 true 1.354,1.083 1.771,0.667 true 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDL+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDL- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDL+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDL- 0.854,0.615 1.271,1.031 0.417,0.417 10 false M15 0.635,3.667 1.052,4.083 0.417,0.417 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - J5-1 (BDL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

53.CHECK WIRE HARNESS (SHORT)

NG

61.CHECK FLOOR WIRE (OPEN)
53.CHECK WIRE HARNESS (SHORT)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - J5-1 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

54.CHECK WIRE HARNESS (SHORT TO B+)

NG

60.CHECK FLOOR WIRE (SHORT)
54.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J5-2 (BDL+) - Body ground Power switch on (IG) Below 1 V
J5-1 (BDL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

55.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

59.CHECK FLOOR WIRE (SHORT TO B+)
55.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C18
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDL- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDL+ 0.792,2.24 1.188,2.594 0.396,0.354 10 false J5
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-2 (BDL+) - Body ground Always 1 MΩ or higher
J5-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

56.CHECK NO. 2 SIDE AIRBAG SENSOR LH

NG

58.CHECK FLOOR WIRE (SHORT TO GROUND)
56.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor LH


Connect the connector to the door side airbag sensor LH.


b.

Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B167B or B167C is output. A
DTC B166D or B166E is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

57.CHECK DOOR SIDE AIRBAG SENSOR LH

B

C

57.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor LH


Interchange the door side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B167B or B167C is output. A
DTC B166D or B166E is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

58.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - Body ground Always 1 MΩ or higher
JM1-40 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

59.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JM1-22 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM1-40 (BDL-) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

60.CHECK FLOOR WIRE (SHORT)
a.
C284682C25
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.594,1.521 0.906,1.76 0.313,0.24 10 false JM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDL+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDL-
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

61.CHECK FLOOR WIRE (OPEN)
a.
C284681C18
0.823,0.552 1.188,0.802 0.365,0.25 0.458,2.823 0.833,3.042 0.375,0.219 1.781,4.302 1.406,3.771 true 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.323,1.167 1.906,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.302 1.406,3.625 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDL+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDL- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDL+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDL- 0.885,0.594 1.385,0.927 0.5,0.333 10 false M15 0.531,2.854 1.031,3.188 0.5,0.333 10 false JM1
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

62.CHECK NO. 1 SIDE AIRBAG SENSOR LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1627 is output. A
DTC B1622 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

63.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor LH


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1637 is output. A
DTC B1632 is output. B
DTCs B1632 and B1637 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C