Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1925/78  Short in Rear Pretensioner Squib LH Circuit  B1926/78  Open in Rear Pretensioner Squib LH Circuit  B1927/78  Short to GND in Rear Pretensioner Squib LH Circuit  B1928/78  Short to B+ in Rear Pretensioner Squib LH Circuit  


DESCRIPTION

The rear pretensioner squib LH circuit consists of the airbag sensor assembly and rear seat 3 point type outer belt assembly LH.

The airbag sensor assembly uses this circuit to deploy the pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear pretensioner squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1925/78 Short in Rear Pretensioner Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the rear pretensioner squib LH circuit during the primary check.

·

Rear pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1926/78 Open in Rear Pretensioner Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects an open in the rear pretensioner squib LH circuit.

·

Rear pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1927/78 Short to GND in Rear Pretensioner Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a short to ground in the rear pretensioner squib LH circuit.

·

Rear pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1928/78 Short to B+ in Rear Pretensioner Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a short to B+ in the rear pretensioner squib LH circuit.

·

Rear pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag sensor assembly


Applies to check mode

DTC Detection Conditions (B1925/78):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the rear pretensioner squib LH circuit during the primary check ○ - -
Rear pretensioner squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1926/78):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects an open in the rear pretensioner squib LH circuit ○ - -
Rear pretensioner squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1927/78):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to ground in the rear pretensioner squib LH circuit ○ - -
Rear pretensioner squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1928/78):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to B+ in the rear pretensioner squib LH circuit ○ - -
Rear pretensioner squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C370614E06
2.427,1.052 2.583,1.25 0.156,0.198 10 false 1 2.427,1.885 2.583,2.083 0.156,0.198 10 false 2 4.74,1.146 5.208,1.344 0.469,0.198 10 false PLR+ 4.729,1.99 5.198,2.188 0.469,0.198 10 false PLR- 2.031,1.885 2.5,2.083 0.469,0.198 10 false RL- 2,1.052 2.469,1.25 0.469,0.198 10 false RL+ 0.594,2.51 1.063,2.708 0.469,0.198 10 false M46 4.75,3.031 5.927,3.229 1.177,0.198 10 false M1 4.75,3.219 6.49,3.448 1.74,0.229 10 false Airbag Sensor Assembly 0.583,2.667 3.115,3.125 2.531,0.458 10 false Rear Pretensioner Squib LH (Rear Seat 3 Point Type Outer Belt Assembly LH) 4.5,1.052 4.656,1.25 0.156,0.198 10 false 8 4.49,1.885 4.646,2.083 0.156,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238350C08
0.521,1.021 0.521,1.635 false 1.385,0.896 1.385,0.469 1.385,0.469 1.615,0.469 false 0.646,0.875 0.865,1.167 0.219,0.292 10 D 1.052,0.875 1.417,1.281 0.365,0.406 10 C 1.625,0.875 1.938,1.26 0.313,0.385 10 B 2.021,0.875 2.281,1.26 0.26,0.385 10 A 2.469,1.188 2.771,1.625 0.302,0.438 10 *2 0.448,1.656 0.896,1.99 0.448,0.333 10 *1 1.646,0.385 1.969,0.677 0.323,0.292 10 *3
*1 Rear Seat 3 Point Type Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear seat 3 point type outer belt assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear seat 3 point type outer belt assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the rear seat 3 point type outer belt assembly LH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

NG

REPLACE FLOOR WIRE

2.CHECK REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
a.
C238359C27
0.333,2.25 0.75,2.5 0.417,0.25 0.667,0.667 0.667,1 false 1.802,2.313 1.979,2.313 false 0.594,1.052 0.99,1.396 0.396,0.344 10 false *1 2.26,0.844 2.573,1.177 0.313,0.333 10 false *2 1.813,0.521 2.146,0.979 0.333,0.458 10 false A 1.656,0.521 2.24,0.958 0.583,0.438 10 false B 1.146,0.521 1.698,0.99 0.552,0.469 10 false C 0.781,0.521 1.365,1.063 0.583,0.542 10 false D 0.406,2.292 0.938,2.667 0.531,0.375 10 false M46 2.01,2.229 2.448,2.573 0.438,0.344 10 false SST 0.333,1.75 0.635,2.031 0.302,0.281 10 false *a
*1 Rear Seat 3 Point Type Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Rear Seat 3 Point Type Outer Belt Assembly LH)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear seat 3 point type outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.


HINT:

Codes other than DTCs B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
C238360C25
0.583,2.333 1,2.583 0.417,0.25 0.573,0.667 0.573,1.063 false 1.375,0.667 1.375,1.063 false 1.531,2.333 1.844,2 true 1.021,2 1.323,2.333 true 0.51,1.063 1.01,1.375 0.5,0.313 10 false *1 2.406,0.844 2.781,1.281 0.375,0.438 10 false *2 1.948,0.521 2.25,0.875 0.302,0.354 10 false A 1.573,0.521 1.917,1.063 0.344,0.542 10 false B 1.063,0.521 1.5,0.917 0.438,0.396 10 false C 0.688,0.521 1.125,0.906 0.438,0.385 10 false D 1.313,1.063 1.646,1.417 0.333,0.354 10 false *3 1.885,1.917 2.302,2.26 0.417,0.344 10 false RL- 0.729,1.917 1.115,2.188 0.385,0.271 10 false RL+ 0.354,1.844 0.75,2.135 0.396,0.292 10 false *a 0.656,2.375 1,2.667 0.344,0.292 10 false M46
*1 Rear Seat 3 Point Type Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Rear Seat 3 Point Type Outer Belt Assembly LH)


Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M46-1 (RL+) - Body ground Power switch on (IG) Below 1 V
M46-2 (RL-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M46-1 (RL+) - M46-2 (RL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M46-1 (RL+) - Body ground Always 1 MΩ or higher
M46-2 (RL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M46-1 (RL+) - M46-2 (RL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238353C26
0.802,0.844 0.802,1.167 false 0.938,0.708 1.542,1.438 0.604,0.729 10 false D 1.083,0.708 1.49,1.177 0.406,0.469 10 false C 1.594,0.708 1.885,1.094 0.292,0.385 10 false B 1.75,0.708 2.073,1 0.323,0.292 10 false A 2.188,1.021 2.49,1.354 0.302,0.333 10 false *2 0.719,1.208 1.094,1.563 0.375,0.354 10 false *1
*1 Rear Seat 3 Point Type Outer Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the rear seat 3 point type outer belt assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.


HINT:

Codes other than DTCs B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG