Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a short to ground in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted via CAN communication to each ECU including the airbag sensor assembly. Thus when multiple systems do not enter DTC output mode, there may be a malfunction in the hybrid vehicle control ECU.



WIRING DIAGRAM

C360627E04
0.885,0.688 1.5,0.885 0.615,0.198 10 false CANH 0.906,1.396 1.521,1.594 0.615,0.198 10 false CANL 1.094,2.76 1.708,2.958 0.615,0.198 10 false TC 0.781,4.438 2.76,4.698 1.979,0.26 10 false : CAN Communication Line 1.417,2.625 1.708,2.802 0.292,0.177 10 false 28 5.688,2.635 5.906,2.813 0.219,0.177 10 false 13 5.75,3.25 5.969,3.427 0.219,0.177 10 false 4 5.979,2.75 6.594,2.948 0.615,0.198 10 false TC 5.99,3.375 6.604,3.573 0.615,0.198 10 false CG 6.094,3.906 6.708,4.104 0.615,0.198 10 false F41 6.104,4.104 6.719,4.302 0.615,0.198 10 false DLC3 5.583,1.875 7.156,2.156 1.573,0.281 10 false Airbag Sensor Assembly 5.99,0.677 6.604,0.875 0.615,0.198 10 false CANH 6,1.406 6.615,1.604 0.615,0.198 10 false CANL 0.51,3.906 0.948,4.094 0.438,0.188 10 false F3 0.51,4.073 2.25,4.302 1.74,0.229 10 false Hybrid Vehicle Control ECU

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF HYBRID VEHICLE CONTROL ECU)
a.
C360629C02
1.417,0.333 1.917,0.583 0.5,0.25 1.5,2.167 2,2.417 0.5,0.25 1.677,3.667 2.083,4.083 true 1.667,1.094 2.167,1.75 true 0.563,0.24 0.875,0.396 0.313,0.156 10 false *1 0.771,2.135 1.083,2.292 0.313,0.156 10 false *a 1.542,0.365 1.938,0.615 0.396,0.25 10 false F41 2.177,1.823 2.573,2.073 0.396,0.25 10 false TC 2.094,4.146 2.49,4.396 0.396,0.25 10 false TC 1.667,2.198 2.063,2.448 0.396,0.25 10 false F3
*1 DLC3
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Turn the power switch off.


b.

Disconnect the connector from the hybrid vehicle control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-13 (TC) - F3-28 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C69
0.146,0.625 0.49,0.854 0.344,0.229 1.656,0.792 1.958,0.385 true 0.156,0.135 0.469,0.292 0.313,0.156 10 false *1 0.198,0.656 0.51,0.958 0.313,0.302 10 false F41 2.042,0.292 2.281,0.458 0.24,0.167 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C70
0.156,0.594 0.5,0.823 0.344,0.229 1.844,1.344 2.01,1.688 true 0.125,0.115 0.406,0.396 0.281,0.281 10 false *1 0.219,0.625 0.698,0.823 0.479,0.198 10 false F41 2,1.719 2.333,2.01 0.333,0.292 10 false TC
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-13 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU