Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A1  Short circuit in Power source circuit  


DESCRIPTION

The following DTCs are stored when a malfunction occurs in the parking brake ECU (brake actuator assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A1 Short circuit in Power source circuit Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

Parking brake ECU (brake actuator assembly) power source relay shorted for approximately 60 seconds.


·

Wire harness or connector

·

Electric parking brake switch (electric parking brake switch assembly)

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ -
Electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off - ○
Malfunction Status Parking brake ECU (brake actuator assembly) power source relay is shorted ○ ○
Detection Time Approximately 60 seconds Approximately 60 seconds
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C385552E08
1.396,1.063 2.771,1.26 1.375,0.198 10 false EPB NO. 1 1.25,1.698 3.083,1.896 1.833,0.198 10 false ECU-IG1 NO. 1 4.958,0.792 5.115,0.99 0.156,0.198 10 false 9 5.188,0.896 5.802,1.094 0.615,0.198 10 false BEPB 4.885,1.417 5.198,1.615 0.313,0.198 10 false 26 5.198,1.542 5.51,1.74 0.313,0.198 10 false IG 3.063,2.51 3.677,2.708 0.615,0.198 10 false SWI1 2.99,2.813 3.604,3.01 0.615,0.198 10 false SWO1 5.188,3.229 5.802,3.427 0.615,0.198 10 false SWI2 2.99,3.698 3.604,3.896 0.615,0.198 10 false SWO2 3.542,2.51 3.771,2.708 0.229,0.198 10 false 6 3.542,2.813 3.76,3.021 0.219,0.208 10 false 5 3.542,3.094 3.76,3.292 0.219,0.198 10 false 4 3.542,3.698 3.823,3.885 0.281,0.188 10 false 3 4.885,2.51 5.198,2.708 0.313,0.198 10 false 14 4.885,2.813 5.198,3.01 0.313,0.198 10 false 20 4.885,3.104 5.198,3.302 0.313,0.198 10 false 24 4.885,3.698 5.198,3.896 0.313,0.198 10 false 22 1.135,4.219 1.594,4.417 0.458,0.198 10 false F67 1.135,4.365 3.521,5.167 2.385,0.802 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 4.865,4.771 5.823,4.99 0.958,0.219 10 false A84*2, A85*1 4.865,4.938 6.51,5.365 1.646,0.427 10 false Parking Brake ECU (Brake Actuator Assembly) 5.188,2.625 5.802,2.823 0.615,0.198 10 false SWI1 5.188,2.927 5.802,3.125 0.615,0.198 10 false SWO1 5.188,3.813 5.802,4.01 0.615,0.198 10 false SWO2 3.052,3.104 3.667,3.302 0.615,0.198 10 false SWI2 0.375,5.156 2.063,5.354 1.688,0.198 10 false *1: for LHD 0.375,5.427 2.063,5.625 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BEPB CIRCUIT)
a.
C393510C01
1.583,2.333 2,2.583 0.417,0.25 1.583,0.25 2,0.5 0.417,0.25 2.531,1.146 2.708,0.521 true 2.542,3.281 2.719,2.656 true 1.677,2.375 2.135,2.573 0.458,0.198 10 false A85 1.677,0.292 2.135,0.49 0.458,0.198 10 false A84 2.073,0.292 2.531,0.49 0.458,0.198 10 false *B 2.083,2.375 2.542,2.573 0.458,0.198 10 false *A 0.125,0.083 0.583,0.281 0.458,0.198 10 false *a 2.542,0.323 3,0.521 0.458,0.198 10 false BEPB 2.552,2.469 3.01,2.667 0.458,0.198 10 false BEPB
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Turn the power switch off.


b.

Disconnect the parking brake ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A85-9 (BEPB) - Body ground Power switch off 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
A84-9 (BEPB) - Body ground Power switch off 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - IG POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - IG POWER SOURCE CIRCUIT)
a.
C393510C02
1.583,2.333 2,2.583 0.417,0.25 1.583,0.25 2,0.5 0.417,0.25 2.563,2.125 2.198,1.51 true 2.573,4.25 2.208,3.635 true 1.677,2.375 2.135,2.573 0.458,0.198 10 false A85 0.115,0.073 0.573,0.271 0.458,0.198 10 false *a 1.677,0.292 2.135,0.49 0.458,0.198 10 false A84 2.073,0.281 2.531,0.479 0.458,0.198 10 false *B 2.083,2.365 2.542,2.563 0.458,0.198 10 false *A 2.542,2.167 3,2.365 0.458,0.198 10 false IG 2.552,4.292 3.01,4.49 0.458,0.198 10 false IG
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Turn the power switch off.


b.

Disconnect the parking brake ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A85-26 (IG) - Body ground Power switch off Below 2.5 V

for RHD
Tester Connection Switch Condition Specified Condition
A84-26 (IG) - Body ground Power switch off Below 2.5 V


Result:
Proceed to
OK
NG




OK

3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.
C393510C03
1.583,2.333 2,2.583 0.417,0.25 1.583,0.25 2,0.5 0.417,0.25 2.198,1.323 2.615,0.49 true 0.708,2.156 1.458,1.51 true 2.5,2.146 1.948,1.51 true 1.313,2.146 1.708,1.521 true 0.719,4.281 1.469,3.635 true 1.313,4.26 1.708,3.635 true 2.51,4.271 1.958,3.635 true 2.208,3.458 2.625,2.625 true 1.677,2.375 2.135,2.573 0.458,0.198 10 false A85 1.677,0.292 2.135,0.49 0.458,0.198 10 false A84 2.073,0.292 2.531,0.49 0.458,0.198 10 false *B 2.083,2.375 2.542,2.573 0.458,0.198 10 false *A 0.125,0.083 0.583,0.281 0.458,0.198 10 false *a 2.448,0.313 2.906,0.51 0.458,0.198 10 false SWI1 1.083,2.188 1.542,2.385 0.458,0.198 10 false SWO2 0.458,2.188 0.917,2.385 0.458,0.198 10 false SWO1 2.448,2.448 2.906,2.646 0.458,0.198 10 false SWI1 2.354,2.188 2.813,2.385 0.458,0.198 10 false SWI2 2.365,4.313 2.823,4.51 0.458,0.198 10 false SWI2 1.094,4.313 1.552,4.51 0.458,0.198 10 false SWO2 0.469,4.313 0.927,4.51 0.458,0.198 10 false SWO1
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Disconnect the parking brake ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A85-14 (SWI1) - Body ground Always 10 kΩ or higher
A85-20 (SWO1) - Body ground Always 10 kΩ or higher
A85-24 (SWI2) - Body ground Always 10 kΩ or higher
A85-22 (SWO2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A84-14 (SWI1) - Body ground Always 10 kΩ or higher
A84-20 (SWO1) - Body ground Always 10 kΩ or higher
A84-24 (SWI2) - Body ground Always 10 kΩ or higher
A84-22 (SWO2) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR