When the power switch is turned on (IG), power is supplied to the parking brake ECU (brake actuator assembly). This DTC is stored if IG power source voltage is not supplied to the parking brake ECU (brake actuator assembly) when communication with other ECUs is established.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C13A2 | Engine Switch/Power Switch Malfunction | Both of following conditions are met:
1.
Power switch on (IG) 2.
When hybrid vehicle control ECU communicates with main body ECU (multiplex network body ECU) via CAN communication, IG power supply voltage is not received for approximately 3 seconds. |
·
Wire harness or connector ·
IG power source circuit ·
Parking brake ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.
When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the power switch is first turned on (IG).
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Electric Parking Brake / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG Switch | IG power source status | OFF or ON | OFF: IG power source voltage is not input to skid control ECU (brake booster with master cylinder assembly)
ON: IG power source voltage is input to skid control ECU (brake booster with master cylinder assembly) |
- |
| Tester Display |
|---|
| IG Switch |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Check for DTCs.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are output (for LHD) | A |
| DTCs are output (for RHD) | B |
| DTCs are not output | C |
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the parking brake ECU (brake actuator assembly) connectors.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly) |
- | - |
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-26 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A84-26 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A85-2 (EGND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A84-2 (EGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG