| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Electric Parking Brake ECU Communication Stop Mode | Any of the following conditions are met:
·
·
|
·
Brake actuator assembly branch line or connector ·
Power source circuit of brake actuator assembly ·
Brake actuator assembly ground circuit ·
Brake actuator assembly |
for LHD
for RHD
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Drive the vehicle at a speed of 15 km/h (9 mph) or more for approximately 10 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Inspect the fuses for circuits related to this system before performing the following procedure.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Brake actuator assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A85-12 (CANH) - A85-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A84-12 (CANH) - A84-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Brake actuator assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A85-2 (EGND) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A84-2 (EGND) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Brake actuator assembly) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-9 (BEPB) - Body ground | Power switch off | 11 to 14 V |
| A85-26 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A84-9 (BEPB) - Body ground | Power switch off | 11 to 14 V |
| A84-26 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
| Result |
|---|
| OK |
| NG |
OK
NG