Refer to the description for DTC P1AC000.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1AC000
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P1CBE1E | Hybrid/EV Battery Block 1 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CBF1E | Hybrid/EV Battery Block 2 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CC01E | Hybrid/EV Battery Block 3 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CC11E | Hybrid/EV Battery Block 4 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CC21E | Hybrid/EV Battery Block 5 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CC31E | Hybrid/EV Battery Block 6 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CC41E | Hybrid/EV Battery Block 7 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CC51E | Hybrid/EV Battery Block 8 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
| P1CC61E | Hybrid/EV Battery Block 9 Voltage Difference Out of Range | An internal malfunction of the HV battery is detected. The difference in voltage of each battery block is higher than the specified value.
(1 trip detection logic) |
·
Battery voltage sensor ·
HV battery ·
Hybrid battery terminal block |
Comes on | Master Warning:
Comes on |
These DTCs can be stored after clearing DTCs and driving the vehicle for approximately 10 minutes.
These DTCs are stored when a malfunction is detected in the HV battery or a battery voltage sensor. However, depending on the driving conditions, the malfunction may not be reproduced if the condition of the HV battery changes.
When the HV battery is malfunctioning:
- Voltage of all battery blocks is output randomly with no certain pattern.
When the battery voltage sensor is malfunctioning:
- Differences in battery block voltages have a certain pattern.
In order to ensure HV battery performance, appropriate cooling performance must be maintained. Perform the following items as necessary. If cooling performance has decreased and "Hybrid Battery Cooling Warning" is displayed on the multi-information display, make sure to perform the following items:
Make sure the air intake port is not blocked.
Make sure there are no gaps between the connecting parts of the ducts.
Clean the No. 1 HV battery intake filter.
Clear the DTCs to reset the learning values even if no DTCs are stored.
| DTC No. | Data List |
|---|---|
| P1CBE1E | ·
Hybrid Battery Block 1 to 9 Voltage *1 ·
Internal Resistance 1 to 9 |
| P1CBF1E | |
| P1CC01E | |
| P1CC11E | |
| P1CC21E | |
| P1CC31E | |
| P1CC41E | |
| P1CC51E | |
| P1CC61E |
*1: Under normal conditions, the values of Hybrid Battery Block 1, 2, 8 and 9 Voltage will be approximately 16 V and Hybrid Battery Block 3, 4, 5, 6 and 7 Voltage will be approximately 32 V.
If there is a short or open in a battery block voltage detection line, the value of Hybrid Battery Block Voltage for the corresponding battery block will be lower than 8 V.
The Data List items Internal Resistance 1 to 9 indicate internal resistance correction values used by the hybrid vehicle control ECU to detect malfunctions of the HV battery.
The following items can be helpful when performing repairs:
Ready Signal
Vehicle Speed
Accelerator Position
Shift Position
Engine Speed
Hybrid Battery Voltage
Hybrid Battery Current
BATT Voltage
SOC just after IG-ON
Maximum SOC
Minimum SOC
Total Distance Traveled
Distance from DTC Cleared
Engine Run Time
Hybrid Battery Voltage Low
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Drive the vehicle on urban roads for approximately 10 minutes.
This DTC may not be stored if the vehicle is stopped or being driven at a constant speed.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
| *a | Dealer |
| *b | Battery Collection Agent |
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0AFC00, P0AFC96, P308A12 or P0AFC62 is not output. | A |
| P0AFC00, P0AFC96, P308A12 or P0AFC62 is also output. | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
Using the GTS, make a note of the freeze frame data item "Hybrid Battery Block (3 to 7) Voltage".
Compare the freeze frame data item "Hybrid Battery Block (3 to 7) Voltage" values with those shown in the following combination tables.
| Condition |
|---|
| "Hybrid Battery Block 3 Voltage" - "Hybrid Battery Block 4 Voltage" = 1.2 V or more |
| "Hybrid Battery Block 4 Voltage" - "Hybrid Battery Block 3 Voltage" = 1.2 V or more |
| "Hybrid Battery Block 4 Voltage" - "Hybrid Battery Block 5 Voltage" = 1.2 V or more |
| "Hybrid Battery Block 5 Voltage" - "Hybrid Battery Block 4 Voltage" = 1.2 V or more |
| "Hybrid Battery Block 5 Voltage" - "Hybrid Battery Block 6 Voltage" = 1.2 V or more |
| "Hybrid Battery Block 6 Voltage" - "Hybrid Battery Block 5 Voltage" = 1.2 V or more |
| "Hybrid Battery Block 6 Voltage" - "Hybrid Battery Block 7 Voltage" = 1.2 V or more |
| "Hybrid Battery Block 7 Voltage" - "Hybrid Battery Block 6 Voltage" = 1.2 V or more |
| *a | Hybrid Battery Block 1 Voltage | *b | Hybrid Battery Block 2 Voltage |
| *c | Hybrid Battery Block 3 Voltage | *d | Hybrid Battery Block 4 Voltage |
| *e | Hybrid Battery Block 5 Voltage | *f | Hybrid Battery Block 6 Voltage |
| *g | Hybrid Battery Block 7 Voltage | *h | Hybrid Battery Block 8 Voltage |
| *i | Hybrid Battery Block 9 Voltage | - | - |
| Result | Proceed to |
|---|---|
| On the HV battery blocks 3 to 7, one of the conditions in the table above is met. | A |
| Other than above | B |
Turn the power switch off.
A
B
Read the odometer to check the total distance the vehicle has been driven.
| Result | Proceed to | |
|---|---|---|
| Total distance driven is less than 200000 km (124280 mile) | A | |
| Total distance driven is 200000 km (124280 mile) or more | Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1 | |
| Other than above | B | |
*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
Using the GTS, make a note of the freeze frame data item "Hybrid Battery Block 1, 2, 8 and 9 Voltage".
Compare the freeze frame data item "Hybrid Battery Block 1, 2, 8 and 9 Voltage" values with those shown in the following combination tables.
| Circuit A Battery Block | Circuit B Battery Block | Condition |
|---|---|---|
| Hybrid Battery Block 1 Voltage | Hybrid Battery Block 2 Voltage | "Hybrid Battery Block 1 Voltage" - "Hybrid Battery Block 2 Voltage" = 1.2 V or more |
| Hybrid Battery Block 8 Voltage | Hybrid Battery Block 9 Voltage | "Hybrid Battery Block 8 Voltage" - "Hybrid Battery Block 9 Voltage" = 1.2 V or more |
| Circuit A Battery Block | Circuit B Battery Block | Condition |
|---|---|---|
| Hybrid Battery Block 1 Voltage | Hybrid Battery Block 2 Voltage | "Hybrid Battery Block 2 Voltage" - "Hybrid Battery Block 1 Voltage" = 1.2 V or more |
| Hybrid Battery Block 8 Voltage | Hybrid Battery Block 9 Voltage | "Hybrid Battery Block 9 Voltage" - "Hybrid Battery Block 8 Voltage" = 1.2 V or more |
| *a | Hybrid Battery Block 1 Voltage | *b | Hybrid Battery Block 2 Voltage |
| *c | Hybrid Battery Block 3 Voltage | *d | Hybrid Battery Block 4 Voltage |
| *e | Hybrid Battery Block 5 Voltage | *f | Hybrid Battery Block 6 Voltage |
| *g | Hybrid Battery Block 7 Voltage | *h | Hybrid Battery Block 8 Voltage |
| *i | Hybrid Battery Block 9 Voltage | - | - |
If an internal malfunction occurs in the battery voltage sensor, this symptom (difference in voltage of 1.2 V or more for certain pairs of blocks as shown in the illustration) will occur.
| Result | Proceed to |
|---|---|
| Either of the following conditions is met:
1. All conditions in table 1 are met. 2. All conditions in table 2 are met. |
A |
| Other than above | B |
Turn the power switch off.
A
B
Read the odometer to check the total distance the vehicle has been driven.
| Result | Proceed to | |
|---|---|---|
| Total distance driven is less than 200000 km (124280 mile) | A | |
| Total distance driven is 200000 km (124280 mile) or more | Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1 | |
| Other than above | B | |
*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT