Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › from 2019.09
RM32K0E _59 Vehicle Exterior _061311 WINDOW / GLASS _0302415 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.
B149736

When reusing the back door glass:

i.

Using a scraper, remove any remaining adhesive residue from the back window glass.

NOTICE:

Be careful not to damage the back door glass.



ii.

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back window glass surface after cleaning it.

·

Even if using a new back door glass, clean it with a non-residue solvent.





Hide 2.INSTALL BACK DOOR GLASS SPACER (for Upper Side)

a.

Using a brush or sponge, coat the installation area of the back door glass spacer with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B454735C01
2.229,1.396 2.417,1.167 false 1.188,1.396 1,1.167 false 0.177,0.125 0.49,0.448 0.313,0.323 10 false *a 0.813,1.01 1.125,1.167 0.313,0.156 10 false *b 2.479,1.021 2.792,1.177 0.313,0.156 10 false *b
*a Back Side of Back Door Glass
*b Ceramic Notch


Install 2 new back door glass spacers to the back door glass as shown in the illustration.


Hide 3.INSTALL BACK DOOR GLASS SPACER (for Lower Side)

a.

for Type B:

i.

Using a brush or sponge, coat the installation area of the back door glass spacer with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



ii.
B563145C02
2.229,1.313 2.417,1.083 false 1.177,1.313 0.99,1.083 false 0.177,0.125 0.49,0.448 0.313,0.323 10 false *a 0.813,0.979 1.125,1.135 0.313,0.156 10 false *b 2.479,0.969 2.792,1.125 0.313,0.156 10 false *b
*a Back Side of Back Door Glass
*b Ceramic Notch


Install 2 new back door glass spacers to the back door glass as shown in the illustration.



Hide 4.INSTALL BACK DOOR GLASS SPACER (for Side)

a.

Using a brush or sponge, coat the installation area of the back door glass spacer with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

for Type A:

i.
B454736C02
1.708,0.917 2.031,0.76 false 1.115,1.531 1.438,1.375 false 1.344,2 1.667,1.844 false 0.167,0.135 0.427,0.365 0.26,0.229 10 false *a 2.083,0.667 2.396,0.823 0.313,0.156 10 false *b 0.896,1.427 1.208,1.583 0.313,0.156 10 false *b 1.125,1.896 1.438,2.052 0.313,0.156 10 false *b
*a Back Side of Back Door Glass
*b Ceramic Notch


Install 4 new back door glass spacers to the back door glass as shown in the illustration.



c.

for Type B:

i.
B563144C03
1.708,0.917 2.031,0.76 false 1.115,1.531 1.438,1.375 false 1.344,2 1.667,1.844 false 0.167,0.135 0.427,0.365 0.26,0.229 10 false *a 2.083,0.667 2.396,0.823 0.313,0.156 10 false *b 0.896,1.427 1.208,1.583 0.313,0.156 10 false *b 1.125,1.896 1.438,2.052 0.313,0.156 10 false *b
*a Back Side of Back Door Glass
*b Ceramic Notch


Install 2 new back door glass spacers to the back door glass as shown in the illustration.



Hide 75575D 5.INSTALL BACK WINDOW LOWER MOULDING (for Type A)

a.

Using a brush or sponge, coat the installation area of the back window lower moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B454741C02
0.115,0.073 0.365,0.313 0.25,0.24 10 false *a 0.396,1.156 0.552,1.333 0.156,0.177 10 true C 0.219,1.51 0.375,1.688 0.156,0.177 10 false C 1.229,1.573 1.385,1.75 0.156,0.177 10 true A 1.271,1.99 1.427,2.167 0.156,0.177 10 false A 1.969,1.667 2.125,1.844 0.156,0.177 10 true B 2.25,2.031 2.406,2.208 0.156,0.177 10 false B 0.313,2.552 0.615,2.75 0.302,0.198 10 false A-A 1.969,2.563 2.271,2.76 0.302,0.198 10 false B-B 1.146,3.646 1.448,3.844 0.302,0.198 10 false C-C 0.938,3.24 1.073,3.427 0.135,0.188 10 false a 2.646,3.26 2.781,3.448 0.135,0.188 10 false b 1.76,4.313 1.896,4.5 0.135,0.188 10 false c
*a Back Side of Back Door Glass


Install a new back window lower moulding to the back door glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 10.3 mm (0.406 in.)
b 18.5 mm (0.728 in.)
c 15.1 mm (0.594 in.)



Hide 75575D 6.INSTALL BACK WINDOW LOWER MOULDING (for Type B)

a.

Using a brush or sponge, coat the installation area of the back window lower moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B539822C01
0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.26,2 1.438,2.198 0.177,0.198 10 false A 1.229,1.552 1.406,1.75 0.177,0.198 10 true A 1.885,1.635 2.063,1.833 0.177,0.198 10 true B 2.208,2.021 2.385,2.219 0.177,0.198 10 false B 0.198,2.385 0.615,2.583 0.417,0.198 10 false A-A 1.865,2.396 2.281,2.594 0.417,0.198 10 false B-B 0.917,3.115 1.135,3.313 0.219,0.198 10 false a 2.635,3.104 2.854,3.302 0.219,0.198 10 false b
*a Back Side of Back Door Glass


Install a new back window lower moulding to the back door glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 10.3 mm (0.406 in.)
b 10.3 mm (0.406 in.)



Hide 64819B 7.INSTALL NO. 2 BACK WINDOW GLASS SPACER

a.

Using a brush or sponge, coat the installation area of the No. 2 back window glass spacer with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B454738C02
1.646,0.958 1.458,0.594 1.458,0.594 1.74,0.875 true 1.865,1.135 2.24,1.208 2.24,1.208 2,0.969 true 0.094,0.094 0.333,0.333 0.24,0.24 10 false *a 1.271,0.469 1.479,0.667 0.208,0.198 10 false *b 2.302,1.146 2.51,1.344 0.208,0.198 10 false *b
*a Back Side of Back Door Glass
*b Ceramic Notch


Install a new No. 2 back window glass spacer to the back door glass as shown in the illustration.


Hide 64818C 8.INSTALL NO. 1 BACK WINDOW GLASS SPACER

HINT:

Use the same procedure as for the No. 2 back window glass spacer.


Hide 75574B 9.INSTALL BACK WINDOW OUTSIDE MOULDING LH

a.

Using a brush or sponge, coat the installation area of the back window outside moulding LH with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B454740C01
0.167,0.094 0.5,0.417 0.333,0.323 10 false *a 2.813,0.781 2.969,0.938 0.156,0.156 10 true A 3.229,0.854 3.385,1.052 0.156,0.198 10 false A 1.854,3.854 2.01,4.052 0.156,0.198 10 false a 1.021,3.01 1.521,3.177 0.5,0.167 10 false A-A
*a Back Side of Back Door Glass


Install a new back window outside moulding LH to the back door glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 9.9 mm (0.390 in.)



Hide 75573C 10.INSTALL BACK WINDOW OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 68131 11.INSTALL BACK DOOR GLASS

a.
B388057

Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.




b.

Back door glass preliminary installation procedures:

i.

Install the suction cups to the back door glass.


ii.

Temporarily place the back door glass onto the vehicle body and set it so that the gap between the body and upper portion and sides of the back door glass is even.



c.
B454725C02
1.49,0.667 1.656,0.667 true 1.49,1 1.49,0.365 1.49,0.365 1.656,0.365 true 1.396,1 1.646,1.198 0.25,0.198 10 true *a
*a Matchmark


Position the back door glass.

i.

Using suction cups, place the back door glass in the correct position.


ii.

Check that the whole contact surface of the back door glass rim is perfectly even.


iii.

Align the matchmarks on the back door glass and back door panel.

NOTICE:

Check that the No. 1 and No. 2 back window glass spacers are engaged to the back door panel correctly.



iv.

Remove the back door glass.



d.

Using a brush, coat the installation surfaces on the back door panel with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



e.

for Type A:

i.

Using a brush or sponge, coat the adhesive application area with primer G.

B454742C01
3.833,3.031 4.333,3.26 4.333,3.26 3.958,2.917 true 3.927,2.958 4.25,3.208 true 0.771,3.323 1.156,3.125 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.01,1.469 2.177,1.656 0.167,0.188 10 false A 2,1.802 2.167,1.99 0.167,0.188 10 true A 1.969,3.177 2.135,3.365 0.167,0.188 10 true C 1.99,3.51 2.156,3.698 0.167,0.188 10 false C 3.281,3.396 3.448,3.583 0.167,0.188 10 false B 3.031,3.083 3.198,3.271 0.167,0.188 10 true B 5.208,0.604 5.479,0.813 0.271,0.208 10 false A-A 5.094,1.979 5.365,2.188 0.271,0.208 10 false B-B 5.104,3.323 5.469,3.5 0.365,0.177 10 false C-C 5.885,0.604 6.063,0.76 0.177,0.156 10 false b 5.583,1.292 5.76,1.448 0.177,0.156 10 false a 5.76,1.5 5.938,1.656 0.177,0.156 10 false a 5.646,1.948 5.823,2.104 0.177,0.156 10 false c 5.292,2.76 5.448,2.938 0.156,0.177 10 false d 5.583,3.333 5.74,3.51 0.156,0.177 10 false e 5.344,4.135 5.51,4.313 0.167,0.177 10 false f 4.406,3.198 4.615,3.385 0.208,0.188 10 false *c 0.583,3.25 0.792,3.438 0.208,0.188 10 false *b
*a Back Side of Back Door Glass *b Adhesive Positioning Center
*c Ceramic Notch - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 7.0 mm (0.276 in.) or more
b 15.3 mm (0.602 in.)
c 7.0 mm (0.276 in.) or more
d 18.5 mm (0.728 in.)
e 7.0 mm (0.276 in.) or more
f 12.3 mm (0.484 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.





f.

for Type B:

i.

Using a brush or sponge, coat the adhesive application area with primer G.

B563146C02
3.865,2.99 4.333,3.26 4.333,3.26 3.99,2.906 true 3.927,2.958 4.25,3.208 true 0.74,3.281 1.125,3.083 true 5.417,2.094 5.677,2.333 false 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.979,1.365 2.146,1.552 0.167,0.188 10 false A 1.958,1.698 2.125,1.885 0.167,0.188 10 true A 1.969,3.177 2.135,3.365 0.167,0.188 10 true C 1.99,3.552 2.156,3.74 0.167,0.188 10 false C 3.438,3.354 3.604,3.542 0.167,0.188 10 false B 3.104,2.938 3.271,3.125 0.167,0.188 10 true B 4.833,0.552 5.104,0.76 0.271,0.208 10 false A-A 4.813,1.875 5.083,2.083 0.271,0.208 10 false B-B 4.854,3.24 5.219,3.417 0.365,0.177 10 false C-C 5.885,0.604 6.063,0.76 0.177,0.156 10 false b 5.583,1.292 5.76,1.448 0.177,0.156 10 false a 5.76,1.5 5.938,1.656 0.177,0.156 10 false a 5.865,1.854 6.042,2.01 0.177,0.156 10 false c 6,2.844 6.156,3.021 0.156,0.177 10 false d 5.583,3.333 5.74,3.51 0.156,0.177 10 false e 5.344,4.135 5.51,4.313 0.167,0.177 10 false f 4.406,3.198 4.615,3.385 0.208,0.188 10 false *c 0.573,3.24 0.781,3.427 0.208,0.188 10 false *b 5.208,2.021 5.521,2.219 0.313,0.198 10 false *1
*1 Back Door Glass Spacer - -
*a Back Side of Back Door Glass *b Adhesive Positioning Center
*c Ceramic Notch - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 7.0 mm (0.276 in.) or more
b 15.3 mm (0.602 in.)
c 7.0 mm (0.276 in.) or more
d 7.0 mm (0.276 in.) or more
e 7.0 mm (0.276 in.) or more
f 12.3 mm (0.484 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.





g.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.



h.

for Type A:

i.

Apply adhesive to the back door glass as shown in the illustration.

B454743C01
0.781,3.375 1.167,3.125 true 3.844,3.042 4.406,3.281 4.406,3.281 3.979,2.927 true 3.938,2.979 4.333,3.24 true 0.125,0.125 0.5,0.365 0.375,0.24 10 false *a 2.01,1.479 2.146,1.646 0.135,0.167 10 false A 2.01,1.823 2.146,1.99 0.135,0.167 10 true A 0.552,3.313 0.719,3.479 0.167,0.167 10 true *b 4.469,3.219 4.667,3.396 0.198,0.177 10 true *c 2.01,3.167 2.146,3.333 0.135,0.167 10 true C 2.01,3.51 2.146,3.677 0.135,0.167 10 false C 3.281,3.406 3.417,3.573 0.135,0.167 10 false B 3.063,3.073 3.198,3.24 0.135,0.167 10 true B 5.146,0.667 5.448,0.844 0.302,0.177 10 false A-A 5.885,1.375 6.021,1.583 0.135,0.208 10 false a 5.063,1.99 5.365,2.167 0.302,0.177 10 false B-B 5.292,2.75 5.427,2.958 0.135,0.208 10 false b 5.125,3.333 5.427,3.51 0.302,0.177 10 false C-C 5.323,4.094 5.458,4.302 0.135,0.208 10 false c
*a Back Side of Back Door Glass *b Adhesive Positioning Center
*c Ceramic Notch - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 15.3 mm (0.602 in.)
b 18.5 mm (0.728 in.)
c 12.3 mm (0.484 in.)


HINT:

Apply adhesive to the ceramic notches.




i.

for Type B:

i.

Apply adhesive to the back door glass as shown in the illustration.

B563147C02
0.729,3.333 1.115,3.083 true 3.865,3 4.406,3.281 4.406,3.281 3.979,2.927 true 3.948,2.948 4.333,3.24 true 5.469,2.031 5.688,2.271 false 0.125,0.125 0.5,0.365 0.375,0.24 10 false *a 2.01,1.365 2.146,1.531 0.135,0.167 10 false A 2,1.698 2.135,1.865 0.135,0.167 10 true A 0.552,3.313 0.719,3.479 0.167,0.167 10 true *b 4.469,3.219 4.667,3.396 0.198,0.177 10 true *c 2.01,3.177 2.146,3.344 0.135,0.167 10 true C 2.01,3.552 2.146,3.719 0.135,0.167 10 false C 3.375,3.354 3.51,3.521 0.135,0.167 10 false B 3.156,2.938 3.292,3.104 0.135,0.167 10 true B 4.771,0.406 5.073,0.583 0.302,0.177 10 false A-A 5.885,1.375 6.021,1.583 0.135,0.208 10 false a 4.823,1.76 5.125,1.938 0.302,0.177 10 false B-B 5.885,1.667 6.021,1.875 0.135,0.208 10 false b 4.896,3.167 5.198,3.344 0.302,0.177 10 false C-C 5.323,4.094 5.458,4.302 0.135,0.208 10 false c 5.26,1.958 5.573,2.156 0.313,0.198 10 false *1
*1 Back Door Glass Spacer - -
*a Back Side of Back Door Glass *b Adhesive Positioning Center
*c Ceramic Notch - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 15.3 mm (0.602 in.)
b 6.0 to 8.0 mm (0.236 to 0.315 in.)
c 12.3 mm (0.484 in.)


HINT:

Apply adhesive to the ceramic notches.




j.

Install the back door glass.

i.
B454725C03
1.479,0.865 1.479,0.365 1.479,0.365 1.646,0.365 true 1.49,0.656 1.656,0.656 true 1.396,0.896 1.625,1.063 0.229,0.167 10 true *a
*a Matchmark


Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the No. 1 and No. 2 back window glass spacers are engaged to the back door panel correctly.

·

Check the clearance between the back door panel and back door glass.




ii.
B454727

Lightly press the outer surface of the back door glass to ensure a close fit and engage the No. 1 back window glass spacer and No. 2 back window glass spacer.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back door glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




k.

Connect each connector and engage each clamp.


Hide 82184 12.CONNECT NO. 1 BACK DOOR WIRE

a.

Connect the 2 connectors to the back door glass.


b.

w/ Glass Breakage Sensor:

i.

Connect the connector to the glass breakage sensor.



Hide 86300C 13.CONNECT NO. 2 AMPLIFIER ANTENNA ASSEMBLY (w/ Woofer)

a.

Connect the connector.


Hide 85110R 14.INSTALL REAR LIGHT ASSEMBLY (for Bulb Type)

Hide 85110R 15.INSTALL REAR LIGHT ASSEMBLY (for LED Type)

Hide 85110R 16.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 17.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.