The temperature sensor of the compressor with motor assembly detects the A/C inverter temperature.
If the temperature exceeds the maximum, operation of the compressor with motor assembly will be stopped, and this DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1475 | A/C Inverter Cooling / Heating System Malfunction | Any of the following conditions is met:
·
A/C inverter temperature outside specified range (temperature too high) ·
There is an open to ground in temperature sensor circuit ·
There is a Short to ground in temperature sensor circuit |
·
Cooling fan system ·
Refrigerant volume ·
Compressor with motor assembly ·
CAN communication system |
Memorized |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Power switch on (READY) | ○ | ○ | ○ |
| Malfunction Status | Temperature of the A/C inverter is outside the specified range (temperature is too high) | ○ | - | - |
| There is an open to ground in the temperature sensor circuit | - | ○ | - | |
| There is a short to ground in the temperature sensor circuit | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks.
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.
Using the GTS, check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Engine Cooling Fan | Control electric cooling fan motor | OFF/Low/High | Perform this test when the following conditions are met:
·
Power switch is on (IG) ·
Engine is stopped ·
Shift lever in P |
| Tester Display |
|---|
| Control the Engine Cooling Fan |
Electric cooling fan operates smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install a manifold gauge set.
for HFO-1234yf(R1234yf):
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION
Turn the power switch on (READY).
Read the manifold gauge pressure when the following conditions are met.
Prepare the vehicle according to the table below.
| Item | Condition |
|---|---|
| Vehicle doors | Fully open |
| Temperature setting | MAX COLD |
| Blower speed | HI |
| A/C switch | On |
| Recirculation/fresh switch | RECIRCULATION |
| Interior temperature | 25 to 35°C (77 to 95°F) |
0.15 to 0.25 MPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
1.37 to 1.57 MPa (14 to 16 kgf/cm2, 199 to 228 psi)
| Proceed to | |
|---|---|
| OK | A |
| NG (for HFO-1234yf(R1234yf)) | B |
| NG (for HFC-134a(R134a)) | C |
A
B
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
C
Clear the DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
Turn the power switch on (READY).
Prepare the vehicle according to the table below.
| Item | Condition |
|---|---|
| Blower speed | HI |
| A/C switch | On |
| Temperature setting | MAX COLD |
Check for DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1475 is not output (normal) | A |
| DTC B1475 is output | B |
If the engine idles continuously when ambient temperature is high, the compressor with motor assembly may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.
A
B