Home › Engine / Hybrid System › M20A-FXS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2019.09
RM32K0E _51 Engine / Hybrid System _083957 M20A-FXS INTAKE / EXHAUST _0404363 EXHAUST MANIFOLD A

M20A-FXS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold and No. 1 exhaust manifold heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.



c.
A440594N02
2.052,0.021 2.208,0.219 0.156,0.198 10 true 1 1.635,0 1.792,0.198 0.156,0.198 10 true 2 2.646,0.052 2.844,0.281 0.198,0.229 10 true 3 1.031,0.052 1.188,0.25 0.156,0.198 10 true 4 2.958,0.406 3.135,0.635 0.177,0.229 10 true 5 0.75,0.906 0.948,1.135 0.198,0.229 10 true 6 0.438,0.156 0.635,0.385 0.198,0.229 10 true 7

Using a 12 mm deep socket wrench, temporarily install the exhaust manifold to the cylinder head sub-assembly with 7 new nuts.


d.

Using the 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A426174N01
2.802,0.583 2.958,0.781 0.156,0.198 10 true 1 0.458,0.51 0.615,0.698 0.156,0.188 10 true 2

Temporarily install the manifold stay to the exhaust manifold and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A450897C01
2.26,0.729 2.458,0.927 0.198,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
Specified tightening torque : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)




Hide 25733A 5.INSTALL NO. 1 VACUUM PIPE

a.

Temporarily install the No. 1 vacuum pipe to the exhaust manifold.


b.

Install the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A432901C01
0.667,1.135 0.833,1.292 0.167,0.156 10 true *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, tighten the flange nut of the No. 1 vacuum pipe.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 26 N*m (265 kgf*cm, 19 ft.*lbf




Hide 58151 6.INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR

a.

Install the No. 1 front floor heat insulator to the vehicle body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 7.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17410 9.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.63 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new exhaust pipe gaskets to the exhaust manifold and front exhaust pipe assembly.


c.
A435170C01
2.51,1.656 2.75,1.396 false 1.823,1.115 1.51,0.708 false 1.938,2.969 2.083,2.427 false 2.792,1.292 3.104,1.49 0.313,0.198 10 false *a 1.844,2.969 2.156,3.167 0.313,0.198 10 false *2 1.302,0.615 1.615,0.813 0.313,0.198 10 false *1
*1 Exhaust Manifold or Front Exhaust Pipe Assembly
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in each exhaust pipe gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gaskets.

·

Do not damage the exhaust pipe gaskets.

·

Do not push in the exhaust pipe gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C45
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold and front exhaust pipe assembly is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C46
2.396,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.104,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.094,0.885 false 0.406,1.417 0.573,1.573 0.167,0.156 10 *a 0.604,0.177 0.802,0.375 0.198,0.198 10 *1 0.604,1.135 0.813,1.333 0.208,0.198 10 *2 2.719,0.115 2.885,0.271 0.167,0.156 10 *3
*1 Front Exhaust Pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Engage the clamp.


h.

Connect the No. 2 air fuel ratio sensor connector.


Hide 57533B 10.INSTALL FRONT FLOOR CENTER BRACE

a.

Install the 3 front floor center braces to the vehicle body with the 12 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 58166 11.INSTALL FRONT FLOOR COVER LH

a.

Engage the 5 clamps to install the front floor cover LH to the vehicle body with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165B 12.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 51441 14.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY