The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
1.INSTALL ENGINE HANGER
2.REMOVE ENGINE FROM ENGINE STAND
Remove the engine assembly from the engine stand.
19315
3.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
13405
4.INSTALL FLYWHEEL SUB-ASSEMBLY
31270
5.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY
88370
6.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY
7.INSTALL ENGINE ASSEMBLY
82121
8.INSTALL ENGINE WIRE
Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.
Install the bolt.
Install the 3 bolts.
Install the bolt.
Install the 3 bolts.
821H2
9.CONNECT HV AIR CONDITIONING WIRE
23819
10.INSTALL NO. 2 FUEL VAPOR FEED PIPE
Install the No. 2 fuel vapor feed pipe to the fuel hose brackets with the bolt and nut.
11363A
11.INSTALL FLYWHEEL HOUSING SIDE COVER
Install the flywheel housing side cover to the cylinder block sub-assembly.
28193
12.INSTALL STARTER HOLE INSULATOR
12305
13.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
| *a | Temporarily Tighten |
Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.
Install the 2 bolts and nut in the order shown in the illustration.
Connect the air conditioner tube and accessory assembly with the bolt and nut.
Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle with the 2 bolts.
12372A
14.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
| *a | Temporarily Tighten |
Temporarily install the engine mounting insulator LH to the vehicle.
Install the 4 bolts and nut in the order shown in the illustration.
15.REMOVE ENGINE HANGER
16.INSTALL EMISSION CONTROL VALVE BRACKET
Install the emission control valve bracket to the cylinder head sub-assembly with the bolt.
89481B
17.INSTALL DIFFERENTIAL PRESSURE SENSOR
18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
Connect the front suspension crossmember sub-assembly to the vehicle with the 6 bolts.
Fully tighten the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads of bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the No. 2 engine mounting stay LH with the bolt.
Install the engine mounting insulator LH to the hybrid vehicle transaxle assembly with the 3 bolts and nut.
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.
51108A
19.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
20.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
21.INSTALL DRIVE SHAFT ASSEMBLY
17410
22.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
45025D
23.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
24.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
25.INSTALL COLUMN HOLE COVER SILENCER SHEET
88704
26.INSTALL SUCTION HOSE SUB-ASSEMBLY
88703
27.INSTALL DISCHARGE HOSE SUB-ASSEMBLY
16267
28.CONNECT NO. 3 WATER BY-PASS HOSE
Engage the clamp to install the No. 3 water by-pass hose.
16283B
29.CONNECT WATER BY-PASS HOSE
Connect the water by-pass hose to the No. 3 water by-pass pipe and slide the hose clip to secure it.
23901
30.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the fuel pump assembly.
Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
Engage the clamp to connect the fuel tube sub-assembly.
87246
31.CONNECT OUTLET HEATER WATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusions of the outlet heater water hose connector with the cutouts in the water hose sub-assembly and push them together until the outlet heater water hose connector makes a "click" sound.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the water hose sub-assembly and outlet heater water hose connector are securely connected by pulling on them.
87245
32.CONNECT INLET HEATER WATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusion of the water hose sub-assembly with the cutout in the inlet heater water hose connector and push them together until the inlet heater water hose makes a "click" sound.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the water hose sub-assembly and inlet heater water hose connector are securely connected by pulling on them.
23825
33.INSTALL FUEL DELIVERY GUARD
Install the fuel delivery guard to the engine mounting bracket RH with the bolt.
23818
34.INSTALL FUEL VAPOR FEED PIPE
Install the fuel vapor feed pipe to the fuel delivery guard with the bolt.
Engage the clamp to connect the No. 1 fuel vapor feed hose.
Engage the clamp to install the engine wire with the bolt.
25860
35.INSTALL PURGE VALVE (PURGE VSV)
23829A
36.INSTALL NO. 1 FUEL VAPOR FEED HOSE
Align the No. 1 fuel vapor feed hose connector with the No. 2 fuel vapor feed pipe, and push them together until the No. 1 fuel vapor feed hose connector makes a "click" sound.
Check that there is no foreign matter on the connecting parts.
After connecting the No. 1 fuel vapor feed hose connector, check that the No. 2 fuel vapor feed pipe and No. 1 fuel vapor feed hose connector are securely connected by pulling on them.
G922F
37.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE
Connect the outlet No. 1 hybrid water pump hose to the motor cooling cooler and slide the clip to secure it.
G922H
38.CONNECT INLET HYBRID RADIATOR HOSE
Connect the inlet hybrid radiator hose to the motor cooling cooler and slide the clip to secure it.
16572D
39.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet sub-assembly and slide the clip to secure it.
Engage the 3 clamps to connect the No. 1 inverter cooling hose assembly and inlet hybrid water pump hose to the fan shroud assembly.
16571C
40.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.
Engage the clamp to connect the No. 1 radiator hose.
33820B
41.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Install the transmission control cable assembly to the control shaft lever with the nut.
G92A0A
42.INSTALL INVERTER RESERVE TANK ASSEMBLY
Connect the inlet hybrid water pump hose to the inverter reserve tank assembly and slide the clip to secure it.
Connect the No. 1 inverter cooling hose assembly to the inverter reserve tank assembly and slide the clip to secure it.
Install the inverter reserve tank assembly with the 2 bolts.
G9200
43.INSTALL INVERTER WITH CONVERTER ASSEMBLY
44.CONNECT ENGINE WIRE
Engage the 3 clamps to connect the engine wire to the vehicle.
Connect the engine wire to the vehicle with the 2 bolts.
Engage the 2 claws to connect the engine wire to the engine room relay block.
Install the nut.
Engage the 2 claws to connect the engine wire to the engine room relay block.
Connect the 3 connectors to the engine room relay block.
82662A
45.INSTALL NO. 1 RELAY BLOCK COVER
Engage the 2 guides and claw to install the No. 1 relay block cover to the engine room relay block.
89661
46.INSTALL ECM
17701
47.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
17801
48.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
49.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
17751
50.INSTALL NO. 1 AIR CLEANER INLET
Install the No. 1 air cleaner inlet to the upper radiator support sub-assembly and air cleaner case sub-assembly with the 4 bolts.
53141F
51.INSTALL RADIATOR COVER
52.ADD ENGINE OIL
53.ADD ENGINE COOLANT (for Engine)
54.ADD HYBRID TRANSAXLE FLUID
55.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
56. WARM UP COMPRESSOR
57.INSPECT HYBRID TRANSAXLE FLUID
58.INSPECT SHIFT LEVER POSITION
59.ADJUST SHIFT LEVER POSITION
60.INSPECT FOR ENGINE OIL LEAK
61.INSPECT FOR COOLANT LEAK (for Inverter)
62.INSPECT FOR COOLANT LEAK (for Engine)
63.INSPECT FOR REFRIGERANT LEAK
64.INSPECT FOR FUEL LEAK
65.INSPECT FOR EXHAUST GAS LEAK
66.CHECK ENGINE OIL LEVEL
67.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK
51444A
68.INSTALL REAR ENGINE UNDER COVER LH
Install the rear engine under cover LH to the vehicle with the 6 clips.
51443C
69.INSTALL REAR ENGINE UNDER COVER RH
Install the rear engine under cover RH to the vehicle with the 6 clips.
51410
70.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
| *a | Bolt |
Install the No. 1 engine under cover assembly to the vehicle with the 4 bolts, 4 screws and 4 clips.
71.INSTALL FRONT WHEELS
72. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
73.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
74.INSPECT IGNITION TIMING
75.INSPECT ENGINE IDLE SPEED
76.INSPECT CO/HC
77.CHECK SPEED SENSOR SIGNAL