Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › 2018.05–2019.09
RM32K0E _51 Engine / Hybrid System _060063 2ZR-FXE FUEL _0294218 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Replacement of fuel pump Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 4.REMOVE REAR SEAT ASSEMBLY

Hide 73480 5.REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

Hide 73380A 6.REMOVE REAR SEAT INNER BELT ASSEMBLY

Hide 71305A 7.REMOVE CENTER REAR SEATBACK HINGE SUB-ASSEMBLY

a.
A395938

Remove the 2 bolts and center rear seatback hinge sub-assembly from the vehicle body.


Hide 82818G 8.REMOVE NO. 8 WIRING HARNESS PROTECTOR

a.

Remove the No. 8 wiring harness protector from the rear floor service hole cover.


Hide 58325E 9.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A374588C01
1.333,0.5 1.458,0.198 1.458,0.198 1.583,0.198 true 1.625,0.125 1.833,0.271 0.208,0.146 10 true *a
*a Protective Tape


Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.


b.
A374319

Disconnect the fuel pump connector.


Hide 77026A 10.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A374353

Slide the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction tube with pump and gauge assembly.


Hide 77754B 11.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A440772

Slide the clip and disconnect the charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.


Hide 77209F 12.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A374356C07
1.969,2.698 2.094,2.406 2.094,2.406 2.229,2.406 false 0.844,2.115 0.969,2.115 0.969,2.115 1.219,1.76 true 1.083,0.219 1.219,0.219 1.219,0.219 1.406,0.583 true 1.281,2.427 1.438,2.427 1.438,2.427 1.521,2.708 false 1.052,3.177 1.594,3.177 false 1.052,3.771 1.219,3.771 1.219,3.771 1.365,3.354 false 2.198,3.344 2.823,3.344 false 2.188,3.49 2.656,3.49 2.656,3.49 2.656,3.344 false 0.875,3.708 1.188,3.865 0.313,0.156 10 false *1 0.865,3.104 1.177,3.26 0.313,0.156 10 false *2 0.906,0.156 1.094,0.323 0.188,0.167 10 true *3 2.281,2.333 2.594,2.49 0.313,0.156 10 false *a 2.865,3.281 3.177,3.438 0.313,0.156 10 false *b 1.104,2.344 1.417,2.5 0.313,0.156 10 false *c 0.656,2.052 0.969,2.208 0.313,0.156 10 false *2
*1 Fuel Suction Plate Sub-assembly
*2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly
*a Fuel Tube Joint
*b O-ring
*c Nylon Tube
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77144 13.REMOVE FUEL PUMP GAUGE RETAINER

a.
A374357C05
0,0 0,0 false
V100135

Front Side


Disengage the claw to remove the No. 1 fuel tube clamp.


b.

Remove the fuel pump gauge retainer.

i.
A374358C08
0.76,0.75 1.188,0.75 true 0.781,0.365 1.292,0.365 true 2.344,0.906 2.615,0.563 2.615,0.563 2.729,0.563 true 2.563,1.177 2.771,1.573 2.771,1.573 2.865,1.573 true 2.229,2.063 2.229,1.365 true 0.948,2.938 1.771,2.938 true 1.833,2.875 2.146,3.031 0.313,0.156 10 false *a 2.927,1.521 3.24,1.677 0.313,0.156 10 false *b 2.146,2.083 2.458,2.24 0.313,0.156 10 false *c 0.604,0.302 0.917,0.458 0.313,0.156 10 false *d 0.583,0.677 0.896,0.833 0.313,0.156 10 false *c 2.792,0.5 3.104,0.656 0.313,0.156 10 false *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A374359C08
1.24,0.396 1.396,0.396 1.396,0.396 1.646,0.948 false 0.573,0.958 0.677,0.958 0.677,0.958 0.833,1.208 false 1.729,2.625 2.469,2.625 true 0.781,0.781 0.885,0.781 0.885,0.781 1.083,1.219 true 1.854,1.646 2,1.354 2,1.354 2.115,1.354 true 0.667,1.552 1,1.552 true 1.49,1.438 1.917,1.156 1.917,1.156 2.031,1.156 true 1.073,0.323 1.385,0.479 0.313,0.156 10 false *a 0.406,0.885 0.719,1.042 0.313,0.156 10 false *b 1.552,2.552 1.865,2.708 0.313,0.156 10 false *c 0.615,0.708 0.927,0.865 0.313,0.156 10 false *d 2.167,1.281 2.479,1.438 0.313,0.156 10 false *d 0.5,1.469 0.813,1.625 0.313,0.156 10 false *c 2.083,1.083 2.396,1.24 0.313,0.156 10 false *e
*a SST (Handle)
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)
*e Extension Bar


Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 14.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A398086

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A374377

Remove the fuel suction tube set gasket from the fuel tank assembly.