Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404405 SFI SYSTEM J

M20A-FXS ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the power switch is first turned to on (IG), the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A373204E61
1.26,0.885 1.875,1.083 0.615,0.198 10 false CANH 1.292,1.594 1.906,1.792 0.615,0.198 10 false CANL 2.833,0.875 3.448,1.073 0.615,0.198 10 false CA5H 5.51,1.573 6.125,1.771 0.615,0.198 10 false CANL 5.51,0.865 6.125,1.063 0.615,0.198 10 false CANH 2.844,1.573 3.458,1.771 0.615,0.198 10 false CA5L 3.927,0.875 4.542,1.073 0.615,0.198 10 false CA4H 3.948,1.583 4.563,1.781 0.615,0.198 10 false CA4L 0.927,3.219 3.042,3.51 2.115,0.292 10 false : CAN Communication Line 2.896,2.25 4.438,2.5 1.542,0.25 10 false Network Gateway ECU 0.083,2.25 2.021,2.573 1.938,0.323 10 false Combination Meter Assembly 6.073,2.26 6.583,2.542 0.51,0.281 10 false ECM 6.094,2.094 6.708,2.292 0.615,0.198 10 false A96 2.906,2.094 3.521,2.292 0.615,0.198 10 false F74 0.094,2.094 0.708,2.292 0.615,0.198 10 false F4 1.729,0.708 2.344,0.906 0.615,0.198 10 false 32 1.729,1.417 2.344,1.615 0.615,0.198 10 false 31 2.604,0.708 3.219,0.906 0.615,0.198 10 false 15 2.604,1.417 3.219,1.615 0.615,0.198 10 false 16 4.365,0.698 4.979,0.896 0.615,0.198 10 false 18 4.365,1.417 4.979,1.615 0.615,0.198 10 false 17 5.333,0.698 5.948,0.896 0.615,0.198 10 false 8 5.271,1.396 5.885,1.594 0.615,0.198 10 false 18

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
MIL Condition Proceed to
Illuminates → Turns off Power switch on (IG) → engine is started A
Other than above - B



A

B

2.CHECK COMMUNICATION BETWEEN GTS AND ECM
2.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
DTCs are not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

4.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY