Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404405 SFI SYSTEM J

M20A-FXS ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the auxiliary battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E85
1.313,0.833 2.615,1.031 1.302,0.198 10 false from EFI NO. 1 Fuse 1.302,1.177 2.656,1.396 1.354,0.219 10 false from EFI-MAIN Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

·

VC Output Circuit

A425734E14
0.542,0.354 0.854,0.552 0.313,0.198 10 false C82 0.552,0.542 2.073,0.927 1.521,0.385 10 false Throttle Body with Motor Assembly 0.531,1.854 0.844,2.052 0.313,0.198 10 false s3 0.521,2.021 2.302,2.24 1.781,0.219 10 false Crankshaft Position Sensor 0.521,3.146 0.833,3.344 0.313,0.198 10 false C78 0.531,3.333 2.146,3.719 1.615,0.385 10 false Camshaft Position Sensor (for Intake Camshaft) 0.521,4.448 0.833,4.646 0.313,0.198 10 false C79 0.521,4.635 2.135,5.021 1.615,0.385 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.521,5.688 0.865,5.896 0.344,0.208 10 false C83 0.521,5.865 2.229,6.229 1.708,0.365 10 false Manifold Absolute Pressure Sensor 0.542,7.073 0.844,7.25 0.302,0.177 10 false C88 0.552,7.24 2.094,7.792 1.542,0.552 10 false Engine Oil Pressure and Temperature Sensor 2.531,0.281 2.781,0.448 0.25,0.167 10 false VC 2.552,0.646 2.771,0.823 0.219,0.177 10 false E2 2.458,1 2.781,1.188 0.323,0.188 10 false VTA 2.396,1.385 2.771,1.563 0.375,0.177 10 false VTA2 2.865,0.531 3.115,0.698 0.25,0.167 10 false 4 2.865,0.177 3.115,0.344 0.25,0.167 10 false 2 2.875,0.906 3.125,1.073 0.25,0.167 10 false 1 2.865,1.26 3.115,1.427 0.25,0.167 10 false 3 2.875,1.781 3.125,1.948 0.25,0.167 10 false 3 2.875,2.146 3.125,2.313 0.25,0.167 10 false 2 2.865,2.521 3.115,2.688 0.25,0.167 10 false 1 2.875,3.052 3.125,3.219 0.25,0.167 10 false 3 2.865,3.417 3.115,3.583 0.25,0.167 10 false 2 2.865,3.76 3.115,3.927 0.25,0.167 10 false 1 2.865,4.729 3.115,4.896 0.25,0.167 10 false 2 2.865,5.073 3.115,5.24 0.25,0.167 10 false 1 2.875,4.354 3.125,4.521 0.25,0.167 10 false 3 2.854,5.646 3.104,5.813 0.25,0.167 10 false 3 2.854,6.021 3.104,6.188 0.25,0.167 10 false 1 2.844,6.375 3.094,6.542 0.25,0.167 10 false 2 2.854,6.969 3.104,7.135 0.25,0.167 10 false 3 2.854,7.313 3.104,7.479 0.25,0.167 10 false 2 2.865,7.708 3.115,7.875 0.25,0.167 10 false 1 2.865,8.094 3.115,8.26 0.25,0.167 10 false 4 2.344,1.885 2.76,2.063 0.417,0.177 10 false VCNE 2.458,2.229 2.75,2.406 0.292,0.177 10 false NE- 2.448,2.604 2.76,2.781 0.313,0.177 10 false NE+ 2.51,3.125 2.76,3.292 0.25,0.167 10 false VC 2.427,3.51 2.75,3.698 0.323,0.188 10 false VVI- 2.438,3.865 2.76,4.052 0.323,0.188 10 false VVI+ 2.448,4.469 2.76,4.646 0.313,0.177 10 false VC2 2.365,4.823 2.75,5.01 0.385,0.188 10 false VVE- 2.344,5.188 2.844,5.375 0.5,0.188 10 false VVE+ 2.521,5.76 2.771,5.927 0.25,0.167 10 false VC 2.542,6.125 2.76,6.302 0.219,0.177 10 false E2 2.469,6.479 2.75,6.656 0.281,0.177 10 false PIM 2.49,7.083 2.74,7.25 0.25,0.167 10 false VC 2.417,7.438 2.781,7.635 0.365,0.198 10 false GND 2.375,7.813 2.781,8.021 0.406,0.208 10 false POUT 2.375,8.208 2.76,8.396 0.385,0.188 10 false TOUT 4.958,0.177 5.229,0.344 0.271,0.167 10 false 109 4.948,0.531 5.219,0.698 0.271,0.167 10 false 110 4.938,0.906 5.208,1.073 0.271,0.167 10 false 108 5,1.26 5.198,1.427 0.198,0.167 10 false 87 4.927,1.771 5.198,1.938 0.271,0.167 10 false 116 4.927,2.135 5.198,2.302 0.271,0.167 10 false 115 5,2.51 5.198,2.677 0.198,0.167 10 false 93 4.99,3.052 5.188,3.219 0.198,0.167 10 false 88 5,3.417 5.198,3.583 0.198,0.167 10 false 89 5,3.781 5.198,3.948 0.198,0.167 10 false 90 4.917,4.354 5.188,4.521 0.271,0.167 10 false 113 4.927,4.729 5.198,4.896 0.271,0.167 10 false 114 4.979,5.094 5.177,5.26 0.198,0.167 10 false 91 4.938,5.635 5.208,5.802 0.271,0.167 10 false 121 4.938,6 5.208,6.167 0.271,0.167 10 false 119 4.927,6.375 5.198,6.542 0.271,0.167 10 false 120 5.01,6.969 5.198,7.146 0.188,0.177 10 false 99 4.938,7.344 5.208,7.51 0.271,0.167 10 false 100 4.927,7.708 5.198,7.875 0.271,0.167 10 false 122 4.958,8.104 5.229,8.271 0.271,0.167 10 false 123 5.646,8.51 5.948,8.688 0.302,0.177 10 false C97 5.615,8.677 5.958,8.854 0.344,0.177 10 false ECM 6.271,0.146 6.542,0.313 0.271,0.167 10 false 5 V 5.302,0.167 5.708,0.344 0.406,0.177 10 false VCTA 5.281,0.521 5.604,0.698 0.323,0.177 10 false ETA 5.281,1.021 5.667,1.208 0.385,0.188 10 false VTA1 5.281,1.375 5.667,1.563 0.385,0.188 10 false VTA2 5.281,1.771 5.708,1.948 0.427,0.177 10 false VCNE 5.271,2.125 5.583,2.302 0.313,0.177 10 false NE- 5.271,2.625 5.583,2.802 0.313,0.177 10 false NE+ 5.281,3.042 5.708,3.219 0.427,0.177 10 false VCV1 5.281,3.406 5.708,3.583 0.427,0.177 10 false VV1- 5.292,3.896 5.719,4.073 0.427,0.177 10 false VV1+ 5.271,4.354 5.698,4.531 0.427,0.177 10 false VCE1 5.281,4.719 5.708,4.896 0.427,0.177 10 false EV1- 5.281,5.198 5.708,5.375 0.427,0.177 10 false EV1+ 5.281,5.625 5.74,5.813 0.458,0.188 10 false VCPM 5.281,6.01 5.698,6.188 0.417,0.177 10 false EPIM 5.281,6.479 5.604,6.667 0.323,0.188 10 false PIM 5.281,6.948 5.719,7.135 0.438,0.188 10 false VCPE 5.271,7.313 5.708,7.5 0.438,0.188 10 false EPEO 5.292,7.823 5.646,8.01 0.354,0.188 10 false PEO 5.281,8.219 5.729,8.406 0.448,0.188 10 false THEO

A431645E05
0.771,0.906 1.229,1.104 0.458,0.198 10 false C84 0.76,1.073 2.135,1.5 1.375,0.427 10 false Mass Air Flow Meter 0.813,2.521 1.271,2.719 0.458,0.198 10 false s2 0.813,2.708 2.333,3.26 1.521,0.552 10 false Fuel Pressure Sensor (for High Pressure Side) 0.781,3.771 1.24,3.969 0.458,0.198 10 false m5 0.781,3.927 2.25,4.594 1.469,0.667 10 false Fuel Pressure Sensor (for Low Pressure Side) 2.656,0.719 2.99,0.906 0.333,0.188 10 false VCC 2.667,1.073 3.125,1.271 0.458,0.198 10 false E2G 2.729,1.438 3.188,1.635 0.458,0.198 10 false FG 2.656,1.802 3.115,2 0.458,0.198 10 false THA 2.76,2.406 3.219,2.604 0.458,0.198 10 false VC 2.76,2.781 3.219,2.979 0.458,0.198 10 false E2 2.74,3.146 3.198,3.344 0.458,0.198 10 false PR 2.75,3.75 3.208,3.948 0.458,0.198 10 false VC 2.76,4.115 3.219,4.313 0.458,0.198 10 false E2 2.688,4.49 3.146,4.688 0.458,0.198 10 false PFL 3.052,3.042 3.51,3.24 0.458,0.198 10 false 3 3.052,0.979 3.51,1.177 0.458,0.198 10 false 2 3.042,1.365 3.5,1.563 0.458,0.198 10 false 3 3.052,1.708 3.51,1.906 0.458,0.198 10 false 1 3.042,2.302 3.5,2.5 0.458,0.198 10 false 1 3.052,2.677 3.51,2.875 0.458,0.198 10 false 2 3.052,0.615 3.51,0.813 0.458,0.198 10 false 4 3.073,3.646 3.531,3.844 0.458,0.198 10 false 1 3.063,4.01 3.521,4.208 0.458,0.198 10 false 3 3.083,4.385 3.542,4.583 0.458,0.198 10 false 2 5.219,0.583 5.677,0.781 0.458,0.198 10 false 78 5.219,0.969 5.677,1.167 0.458,0.198 10 false 79 5.146,1.323 5.604,1.521 0.458,0.198 10 false 101 5.135,1.677 5.594,1.875 0.458,0.198 10 false 102 5.208,2.302 5.667,2.5 0.458,0.198 10 false 98 5.219,2.688 5.677,2.885 0.458,0.198 10 false 96 5.219,3.042 5.677,3.24 0.458,0.198 10 false 97 5.208,3.656 5.667,3.854 0.458,0.198 10 false 84 5.219,4.01 5.677,4.208 0.458,0.198 10 false 61 5.146,4.375 5.604,4.573 0.458,0.198 10 false 107 5.479,0.979 5.938,1.177 0.458,0.198 10 false E2G 5.479,0.604 5.938,0.802 0.458,0.198 10 false VCVG 5.479,1.448 5.938,1.646 0.458,0.198 10 false VG 5.479,1.802 5.938,2 0.458,0.198 10 false THA 5.469,2.323 5.927,2.521 0.458,0.198 10 false VCPR 5.469,2.688 5.927,2.885 0.458,0.198 10 false EPR 5.479,3.146 5.938,3.344 0.458,0.198 10 false PR 5.479,3.667 5.938,3.865 0.458,0.198 10 false VCPF 5.479,4.031 5.938,4.229 0.458,0.198 10 false EPFL 5.479,4.51 5.938,4.708 0.458,0.198 10 false PFL 5.927,6.354 6.385,6.552 0.458,0.198 10 false ECM 5.958,6.198 6.417,6.396 0.458,0.198 10 false C97 0.813,5.25 1.271,5.448 0.458,0.198 10 false C95 0.802,5.427 2.042,5.781 1.24,0.354 10 false Differential Pressure Sensor 2.75,5.167 3.208,5.365 0.458,0.198 10 false VC 2.76,5.531 3.219,5.729 0.458,0.198 10 false E2 2.656,5.896 3.115,6.094 0.458,0.198 10 false PEX 3.063,5.063 3.521,5.26 0.458,0.198 10 false 3 3.052,5.427 3.51,5.625 0.458,0.198 10 false 1 3.063,5.802 3.521,6 0.458,0.198 10 false 2 5.208,5.052 5.438,5.229 0.229,0.177 10 false 69 5.208,5.417 5.438,5.594 0.229,0.177 10 false 68 5.219,5.781 5.448,5.958 0.229,0.177 10 false 92 5.479,5.073 6.01,5.24 0.531,0.167 10 false VCPX 5.479,5.427 6.01,5.594 0.531,0.167 10 false EPEX 5.469,5.927 5.917,6.125 0.448,0.198 10 false PEX


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 3 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 3 FUSE VOLTAGE
A452288C01
2.802,2.833 3.208,1.063 true 1.052,1.573 1.365,1.76 0.313,0.188 10 false *1 3.229,0.958 3.417,1.177 0.188,0.219 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI NO. 3 Fuse


a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (EFI NO. 3 fuse) - Body ground Power Switch on (IG) 11 to 14 V


HINT:
·

Check the fuse with it installed to the No. 1 engine room relay block.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the C82 throttle body with motor assembly connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the s3 crankshaft position sensor connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

5.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the C78 camshaft position sensor (for intake camshaft) connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

6.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the C83 manifold absolute pressure sensor connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the C79 camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

8.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)
a.

Disconnect the C88 engine oil pressure and temperature sensor connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

B

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))
a.

Disconnect the s2 fuel pressure sensor (for high pressure side) connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE))
a.

Disconnect the m5 fuel pressure sensor (for low pressure side) connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER)

B

REPLACE FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE)

11.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER)
a.

Disconnect the C84 mass air flow meter connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

12.CHECK CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR)

B

12.CHECK CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR)
a.

Disconnect the C95 differential pressure sensor connector.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

13.CHECK HARNESS AND CONNECTOR

B

13.CHECK HARNESS AND CONNECTOR
a.

Disconnect the C82 throttle body with motor assembly connector.


b.

Disconnect the s3 crankshaft position sensor connector.


c.

Disconnect the C78 camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the C83 manifold absolute pressure sensor connector.


e.

Disconnect the C79 camshaft position sensor (for exhaust camshaft) connector.


f.

Disconnect the C88 engine oil pressure and temperature sensor connector.


g.

Disconnect the s2 fuel pressure sensor (for high pressure side) connector.


h.

Disconnect the m5 fuel pressure sensor (for low pressure side) connector.


i.

Disconnect the C84 mass air flow meter connector.


j.

Disconnect the C95 differential pressure sensor connector.


k.

Disconnect the A96 and C97 ECM connectors.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C97-109 (VCTA) - Body ground Always 10 kΩ or higher
C97-116 (VCNE) - Body ground Always 10 kΩ or higher
C97-88 (VCV1) - Body ground Always 10 kΩ or higher
C97-113 (VCE1) - Body ground Always 10 kΩ or higher
C97-121 (VCPM) - Body ground Always 10 kΩ or higher
C97-99 (VCPE) - Body ground Always 10 kΩ or higher
C97-78 (VCVG) - Body ground Always 10 kΩ or higher
C97-98 (VCPR) - Body ground Always 10 kΩ or higher
C97-84 (VCPF) - Body ground Always 10 kΩ or higher
C97-69 (VCPX) - Body ground Always 10 kΩ or higher
A96-9 (+B) - 1 (EFI NO. 3 fuse) Always Below 1 Ω
A96-35 (+B2) - 1 (EFI NO. 3 fuse) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR