Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404405 SFI SYSTEM J

M20A-FXS ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the power switch is turned to on (IG), the auxiliary battery voltage is applied to IGSW of the ECM. When the transistor in the MREL circuit operates, current flows from the auxiliary battery to ground through the drive circuit of the EFI-MAIN relay, thus operating the relay which supplies power to the +B and +B2 terminals of the ECM.

WIRING DIAGRAM

A449593E01
2.49,4.625 4.385,4.896 1.896,0.271 10 false No. 1 Integration Relay 0.563,4.844 1.76,5.104 1.198,0.26 10 false Auxiliary Battery 0.417,4.115 1.333,4.365 0.917,0.25 10 false MAIN 0.552,3.375 1.25,3.729 0.698,0.354 10 false EFI-MAIN NO. 1 2.969,3.833 3.885,4.083 0.917,0.25 10 false EFI-MAIN 2.958,2.573 3.875,2.823 0.917,0.25 10 false IG2 NO. 1 0.552,2.115 1.469,2.365 0.917,0.25 10 false IG2-MAIN 1.865,0.969 3.979,1.458 2.115,0.49 10 false Certification ECU (Smart Key ECU Assembly) 1.875,0.792 3.75,1.219 1.875,0.427 10 false F1 3.042,0.365 3.958,0.615 0.917,0.25 10 false IG1D 3.427,0.375 4.344,0.625 0.917,0.25 10 false 17 4.833,2.125 5.938,2.375 1.104,0.25 10 false ECU-IG2 NO. 1 5.177,3.792 6.281,4.042 1.104,0.25 10 false EFI NO. 3 5.323,3.542 6.427,3.792 1.104,0.25 10 false 1 5.615,3.542 6.719,3.792 1.104,0.25 10 false 2 6.167,4.021 6.813,4.302 0.646,0.281 10 false MREL 5.927,4.01 6.344,4.313 0.417,0.302 10 false 15 6.167,1.885 6.813,2.167 0.646,0.281 10 false IGSW 5.979,1.865 6.625,2.146 0.646,0.281 10 false 2 6.188,2.854 6.833,3.135 0.646,0.281 10 false +B 6.188,3.219 6.833,3.5 0.646,0.281 10 false +B2 5.917,3.135 6.563,3.417 0.646,0.281 10 false 35 5.99,2.74 6.635,3.021 0.646,0.281 10 false 9 1.781,3.573 2.427,3.854 0.646,0.281 10 false 1B 6.167,4.667 6.813,4.948 0.646,0.281 10 false E1 5.917,4.542 6.323,4.781 0.406,0.24 10 false 10 6.438,5.344 6.833,5.615 0.396,0.271 10 false ECM 6.438,5.188 7.083,5.469 0.646,0.281 10 false A96 6.75,4.146 6.948,4.448 0.198,0.302 10 false IC 1.833,3.396 2.479,3.677 0.646,0.281 10 false 5 1.781,3.229 2.427,3.51 0.646,0.281 10 false 1B 1.833,3.042 2.479,3.323 0.646,0.281 10 false 3 4.375,3.229 5.021,3.51 0.646,0.281 10 false 1B 4.427,3.042 5.073,3.323 0.646,0.281 10 false 4 4.375,4.125 5.021,4.406 0.646,0.281 10 false 1B 4.417,3.938 5.063,4.219 0.646,0.281 10 false 6 1.771,2.313 2.417,2.594 0.646,0.281 10 false 1A 1.823,2.146 2.469,2.427 0.646,0.281 10 false 8 1.781,1.979 2.427,2.26 0.646,0.281 10 false 1A 1.792,1.792 2.438,2.073 0.646,0.281 10 false 10 3.99,1.677 4.635,1.958 0.646,0.281 10 false 1A 3.813,1.677 4.458,1.958 0.646,0.281 10 false 7 4.365,1.979 5.01,2.26 0.646,0.281 10 false 1A 4.417,1.792 5.063,2.073 0.646,0.281 10 false 9

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
A452302C01
0.344,1.313 0.688,1.604 0.344,0.292 0.385,3.167 0.729,3.458 0.344,0.292 0.135,0.083 0.448,0.24 0.313,0.156 10 false *a 0.417,1.375 0.729,1.531 0.313,0.156 10 false 1A 0.448,3.229 0.76,3.385 0.313,0.156 10 false 1B
*a Front view of wire harness connector
(to No. 1 Integration Relay)


a.

Disconnect the No. 1 integration relay connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1A-10 - Body ground Always 11 to 14 V
1B-3 - Body ground Always 11 to 14 V
1B-5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY, IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)

2.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY, IG2 NO. 1 RELAY)
a.

Inspect the No. 1 integration relay (EFI-MAIN relay, IG2 NO. 1 relay).

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Disconnect the 1A and 1B No. 1 integration relay connectors.


b.

Disconnect the A96 ECM connector.


c.

Remove the VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block.

HINT:

Remove the VVT relay, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-9 - A96-2 (IGSW) Always Below 1 Ω
1B-6 - A96-15 (MREL) Always Below 1 Ω
1B-4 - A96-9 (+B) Always Below 1 Ω
1B-4 - A96-35 (+B2) Always Below 1 Ω
1A-9 or A96-2 (IGSW) - Body ground and other terminals Always 10 kΩ or higher
1B-6 or A96-15 (MREL) - Body ground and other terminals Always 10 kΩ or higher
1B-4, A96-9 (+B) or A96-35 (+B2) - Body ground and other terminals Always 10 kΩ or higher



HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Disconnect the 1A No. 1 integration relay connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1A-8 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A96 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A96-10 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)
A428660C04
0.198,0.917 0.583,1.146 0.385,0.229 1.479,0.813 2.052,0.26 true 0.219,0.25 0.531,0.448 0.313,0.198 10 false *a 2.104,0.156 2.781,0.458 0.677,0.302 10 false IGSW 0.26,0.948 0.573,1.146 0.313,0.198 10 false A96
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A96-2 (IGSW) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 1A No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-17 (IG1D) - 1A-7 Always Below 1 Ω
F1-17 (IG1D) or 1A-7 - Body ground and other terminals Always 10 kΩ or higher



HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR