Refer to DTC P26CA12.
Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>P26CA12
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P26CB71 | Engine Coolant Pump Actuator Stuck | Even though an operation request signal is being output, the engine water pump assembly does not rotate* (1 trip detection logic). | ·
Lack of engine coolant ·
Engine coolant leak ·
Engine water pump assembly (water inlet housing) ·
ECM |
Comes on | DTC stored | SAE Code: P26CB |
*: As the frequency signal (WPI) is 4 Hz when the engine water pump assembly is stopped to enable the ECM to detect an open or short in the signal line, the engine water pump assembly speed will be displayed as approximately 160 rpm even when the pump is stopped. If there is an open in the WPI circuit, the engine water pump speed will be displayed as 0 rpm.
| DTC No. | Data List |
|---|---|
| P26CB71 | ·
Coolant Temperature ·
Electric Water Pump Target Speed ·
Electric Water Pump Speed |
The ECM receives a frequency signal (WPI) from the engine water pump assembly and calculates the speed of the engine water pump assembly. The ECM outputs an operation duty signal (WPO) to steplessly control the speed of the engine water pump assembly. If the duty signal (WPI) indicates that the engine water pump assembly is stopped even though the ECM is outputting an operation duty signal (WPO), the ECM judges that the engine water pump assembly is stuck and stores this DTC.
As the frequency signal (WPI) is 4 Hz when the engine water pump assembly is stopped to enable the ECM to detect an open or short in the signal line, the engine water pump assembly speed will be displayed as approximately 160 rpm even when the pump is stopped.
| Required Sensors/Components | Engine water pump assembly |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) [A].
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and maintain the engine speed at 2500 rpm or more for at least 70 seconds [B].
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P26CB71.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Refer to DTC P26CA12.
Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>P26CA12
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
As the frequency signal (WPI) is 4 Hz when the engine water pump assembly is stopped to enable the ECM to detect an open or short in the signal line, the engine water pump assembly speed will be displayed as approximately 160 rpm even when the pump is stopped.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P26CB71 is output | A |
| DTC P26CB71 and P26CE37 are output | |
| DTC P26CB71 and other DTCs are output | B |
If any DTCs other than P26CB71 are output, troubleshoot those DTCs first.
A
B
Check that the engine coolant level is between the FULL and LOW lines.
Click hereEngine / Hybrid System>M20A-FXS (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| Engine coolant level is above the LOW line | A |
| Engine coolant level is below the LOW line | B |
A
B
Check the areas around the engine and heater for engine coolant leaks.
Click hereEngine / Hybrid System>M20A-FXS (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION
If the engine oil is cloudy during the engine oil level dipstick check, it means that engine coolant has entered the engine lubrication system.
No leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Fill the reservoir tank up to the FULL line with engine coolant.
Make sure not to add engine coolant when the engine is hot.
| Proceed to |
|---|
| NEXT |
NEXT
Repair any engine coolant leaks.
Add engine coolant and perform air bleeding after repair.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Electric Water Pump / Data List / Electric Water Pump Speed.
| Active Test Display |
|---|
| Activate the Electric Water Pump |
| Data List Display |
|---|
| Electric Water Pump Speed |
According to the display on the GTS, read the Data List while performing the Active Test.
| Active Test Operation | Electric Water Pump Speed |
|---|---|
| 3000 rpm | 2000 rpm or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Engine Water Pump Assembly (Water Inlet Housing)) |
Disconnect the water inlet housing with water pump sub-assembly connector.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Engine / Active Test / Activate the Electric Water Pump.
| Tester Display |
|---|
| Activate the Electric Water Pump |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C90-2 (SWP) - Body ground | Power switch on (IG), during Active Test | Resistance fluctuates* |
*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the SWP terminal will be unstable during the Active Test. If the resistance fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.
If the resistance fluctuates after turning the power switch on (IG), it can be determined that the ECM is in fail-safe mode.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine water pump assembly (water inlet housing).
Click hereEngine / Hybrid System>M20A-FXS (COOLING)>WATER PUMP>REMOVAL
When replacing any cooling system parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
If no DTC is output, the repair has been successfully completed.
| Proceed to |
|---|
| NEXT |
NEXT