Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404406 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) J

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  Motor Resolver Circuit  


DESCRIPTION

The cause of this malfunction may be the motor resolver.

Check the motor resolver internal resistance and the connection condition from the inverter to the resolver.

Related Parts Check
Area Inspection Step
Wire harness and connector between the inverter and motor resolver Check for short circuit between wire harness and +B side. 1
Resolver, wire harness, connector Check the internal resistance of resolver (including wire harness), body ground resistance, and connector connection condition. 2, 3
Wire harness Check for open or short circuit in wire harness. 4

SYSTEM DESCRIPTION

A resolver is a sensor that is used to detect the position of the magnetic poles of the rotor of a motor. Knowing the position of the poles is indispensable for ensuring precise control of the motor (MG2).

Each resolver contains a stator that has an excitation coil and 2 detection coils (S, C). The gap between the stator and rotor changes as the rotor turns because the rotor is oval shaped. An alternating current with a predetermined frequency flows through the excitation coil, and detection coils S and C output alternating currents in accordance with the sensor rotor position.

The MG ECU, which is built into the inverter with converter assembly, detects the absolute position of the rotor according to the phases of detection coils S and C and the heights of their waveforms. Furthermore, the CPU calculates the amount of change in the position within a predetermined length of time, in order to use the resolver as a revolution speed sensor.

The MG ECU monitors signals output from the motor resolver and detects malfunctions.

A221242E27
1.406,3.25 0.76,4.542 false 2.229,3.667 1.76,4.844 false 4.5,2.104 4.333,2.417 false 4.521,3.552 3.917,4.156 false 1.323,3.469 1.51,3.719 0.188,0.25 10 -S 1.729,2.188 1.917,2.438 0.188,0.25 10 -S 0.875,2.677 1.115,2.885 0.24,0.208 10 +S 2.156,3.052 2.417,3.25 0.26,0.198 10 +S 1.198,2.219 1.385,2.427 0.188,0.208 10 -C 1.813,3.458 2,3.667 0.188,0.208 10 -C 0.865,3.188 1.073,3.396 0.208,0.208 10 +C 2.135,2.552 2.344,2.76 0.208,0.208 10 +C 0.542,4.563 1.01,4.792 0.469,0.229 10 Rotor 1.323,4.875 2.302,5.115 0.979,0.24 10 Excitation Coil 6.01,0.313 6.99,0.552 0.979,0.24 10 Excitation Coil 5.969,2.031 7.125,2.271 1.156,0.24 10 Detection Coil S 5.969,3.5 7.083,3.74 1.115,0.24 10 Detection Coil C 4.542,2.01 5.646,2.26 1.104,0.25 10 Virtual Waveform 4.552,3.469 5.656,3.719 1.104,0.25 10 Virtual Waveform

WIRING DIAGRAM

C304948E49
0.74,0.385 2.021,0.583 1.281,0.198 10 false Excitation Coil 0.698,2.49 1.469,2.688 0.771,0.198 10 false C1 0.698,2.646 1.979,2.844 1.281,0.198 10 false Motor Resolver 2.594,0.49 3.365,0.688 0.771,0.198 10 false MRF 2.49,0.813 3.26,1.01 0.771,0.198 10 false MRFG 2.583,1.135 3.354,1.333 0.771,0.198 10 false MSN 2.479,1.469 3.25,1.667 0.771,0.198 10 false MSNG 2.573,1.781 3.344,1.979 0.771,0.198 10 false MCS 2.479,2.125 3.25,2.323 0.771,0.198 10 false MCSG 3,0.479 3.771,0.677 0.771,0.198 10 false 6 3.01,0.813 3.781,1.01 0.771,0.198 10 false 9 3.01,1.135 3.781,1.333 0.771,0.198 10 false 4 3.01,1.458 3.781,1.656 0.771,0.198 10 false 5 3.01,1.781 3.781,1.979 0.771,0.198 10 false 10 3.01,2.125 3.781,2.323 0.771,0.198 10 false 14 4.792,0.49 5.583,0.708 0.792,0.219 10 false 5 4.792,0.813 5.583,1.031 0.792,0.219 10 false 6 4.792,1.135 5.583,1.354 0.792,0.219 10 false 1 4.802,1.479 5.594,1.698 0.792,0.219 10 false 2 4.792,1.802 5.583,2.021 0.792,0.219 10 false 4 4.781,2.115 5.573,2.333 0.792,0.219 10 false 3 4.792,2.708 5.583,2.927 0.792,0.219 10 false 7 5.01,0.49 5.781,0.688 0.771,0.198 10 false MRF 5.01,0.813 5.781,1.01 0.771,0.198 10 false MRFG 5.01,1.219 5.781,1.417 0.771,0.198 10 false MSN 5.01,1.552 5.781,1.75 0.771,0.198 10 false MSNG 5.01,1.885 5.781,2.083 0.771,0.198 10 false MCS 5.01,2.208 5.781,2.406 0.771,0.198 10 false MCSG 5.01,2.813 5.781,3.01 0.771,0.198 10 false DRN3 5.646,0.552 6.781,0.76 1.135,0.208 10 false Oscillation Circuit 4.948,3.25 6.979,3.688 2.031,0.438 10 false Inverter with Converter Assembly (MG ECU) 0.573,3.063 3.135,3.26 2.563,0.198 10 false Hybrid Vehicle Transaxle Assembly 4.938,3.104 5.708,3.302 0.771,0.198 10 false C64

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.

·

If the resolver is malfunctioning, the vehicle may not drive smoothly.

·

When inspecting the connectors, if it is difficult to judge if a connector was disconnected, deformed or improperly secured, disconnect and reconnect the connector and then check for DTCs again. Check if the same DTC is output. If the same DTC is not output, improper connection of connectors is suspected.

·

As a malfunction detection threshold may be exceeded when performing the vibration or heat connector inspections, make sure to perform the following inspection to check that the DTC was not stored due to the malfunction of a part.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the inverter with converter assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A365594C09
0.219,0.406 0.552,0.646 0.333,0.24 1.417,0.938 0.573,0.917 true 1.448,1.063 0.625,1.354 true 1.573,0.927 1.281,0.24 true 1.729,1.063 2.427,1.323 true 1.823,0.948 2.406,0.958 true 1.698,0.906 2.344,0.365 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 2.313,0.146 2.771,0.344 0.458,0.198 10 false MCSG 0.25,1.271 0.708,1.469 0.458,0.198 10 false MRF 2.5,1.26 2.958,1.458 0.458,0.198 10 false MRFG 0.219,0.802 0.677,1 0.458,0.198 10 false MSN 0.833,0.125 1.292,0.323 0.458,0.198 10 false MSNG 2.521,0.875 2.979,1.073 0.458,0.198 10 false MCS 0.271,0.438 0.729,0.635 0.458,0.198 10 false C64
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C64-5 (MRF) - Body ground Power switch on (IG) Below 1 V
C64-6 (MRFG) - Body ground Power switch on (IG) Below 1 V
C64-1 (MSN) - Body ground Power switch on (IG) Below 1 V
C64-2 (MSNG) - Body ground Power switch on (IG) Below 1 V
C64-4 (MCS) - Body ground Power switch on (IG) Below 1 V
C64-3 (MCSG) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


h.

Reconnect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MOTOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the inverter with converter assembly connector.


c.
A477755C05
0.219,0.406 0.552,0.646 0.333,0.24 1.438,0.938 0.594,0.917 true 1.448,1.063 0.583,1.188 true 1.552,0.906 1.219,0.26 true 1.719,1.042 2.563,1.229 true 1.823,0.948 2.479,0.688 true 1.698,0.906 2.271,0.333 true 1.458,1.146 0.604,1.469 true 1.479,1.229 0.677,1.771 true 1.573,1.24 1.229,1.927 true 1.698,1.24 1.698,1.875 true 1.792,1.24 2.115,1.938 true 1.833,1.021 2.615,0.948 true 1.729,1.125 2.542,1.469 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 2.323,0.24 2.781,0.438 0.458,0.198 10 false MCSG 0.281,1.125 0.74,1.323 0.458,0.198 10 false MRF 2.615,1.167 3.073,1.365 0.458,0.198 10 false MRFG 0.26,0.844 0.719,1.042 0.458,0.198 10 false MSN 0.823,0.125 1.281,0.323 0.458,0.198 10 false MSNG 2.542,0.615 3,0.813 0.458,0.198 10 false MCS 0.271,0.438 0.729,0.635 0.458,0.198 10 false C64 0.313,1.427 0.771,1.625 0.458,0.198 10 false GRF 0.375,1.74 0.833,1.938 0.458,0.198 10 false GSN 0.844,1.896 1.302,2.094 0.458,0.198 10 false GSNG 1.521,1.927 1.979,2.125 0.458,0.198 10 false GCSG 2.177,1.885 2.635,2.083 0.458,0.198 10 false GCS 2.583,1.448 3.042,1.646 0.458,0.198 10 false GRFG 2.667,0.865 3.125,1.063 0.458,0.198 10 false DRN3
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C64-5 (MRF) - C64-6 (MRFG) Power switch off 8.9 to 14.9 Ω
C64-1 (MSN) - C64-2 (MSNG) Power switch off 16.2 to 28.1 Ω
C64-4 (MCS) - C64-3 (MCSG) Power switch off 18.2 to 30.1 Ω


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F).)


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C64-5 (MRF) or C64-6 (MRFG) - C64-4 (MCS) or C64-3 (MCSG) Power switch off 1 MΩ or higher
C64-5 (MRF) or C64-6 (MRFG) - C64-1 (MSN) or C64-2 (MSNG) Power switch off 1 MΩ or higher
C64-5 (MRF) or C64-6 (MRFG) - C64-8 (GRF) or C64-9 (GRFG) Power switch off 1 MΩ or higher
C64-5 (MRF) or C64-6 (MRFG) - C64-13 (GCS) or C64-12 (GCSG) Power switch off 1 MΩ or higher
C64-5 (MRF) or C64-6 (MRFG) - C64-10 (GSN) or C64-11 (GSNG) Power switch off 1 MΩ or higher
C64-5 (MRF) or C64-6 (MRFG) - C64-7 (DRN3) Power switch off 1 MΩ or higher
C64-5 (MRF) or C64-6 (MRFG) - Body ground Power switch off 1 MΩ or higher
C64-4 (MCS) or C64-3 (MCSG) - C64-1 (MSN) or C64-2 (MSNG) Power switch off 1 MΩ or higher
C64-4 (MCS) or C64-3 (MCSG) - C64-8 (GRF) or C64-9 (GRFG) Power switch off 1 MΩ or higher
C64-4 (MCS) or C64-3 (MCSG) - C64-13 (GCS) or C64-12 (GCSG) Power switch off 1 MΩ or higher
C64-4 (MCS) or C64-3 (MCSG) - C64-10 (GSN) or C64-11 (GSNG) Power switch off 1 MΩ or higher
C64-4 (MCS) or C64-3 (MCSG) - C64-7 (DRN3) Power switch off 1 MΩ or higher
C64-4 (MCS) or C64-3 (MCSG) - Body ground Power switch off 1 MΩ or higher
C64-1 (MSN) or C64-2 (MSNG) - C64-8 (GRF) or C64-9 (GRFG) Power switch off 1 MΩ or higher
C64-1 (MSN) or C64-2 (MSNG) - C64-13 (GCS) or C64-12 (GCSG) Power switch off 1 MΩ or higher
C64-1 (MSN) or C64-2 (MSNG) - C64-10 (GSN) or C64-11 (GSNG) Power switch off 1 MΩ or higher
C64-1 (MSN) or C64-2 (MSNG) - C64-7 (DRN3) Power switch off 1 MΩ or higher
C64-1 (MSN) or C64-2 (MSNG) - Body ground Power switch off 1 MΩ or higher



d.

Reconnect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

MOTOR RESOLVER CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

3.CHECK CONNECTOR CONNECTION CONDITION (RESOLVER CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (RESOLVER CONNECTOR)
a.
A376649

Check the connection condition of the resolver connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)
a.
A376649

Disconnect the resolver connector.


b.
A385117C20
0.083,0.667 0.583,0.917 0.5,0.25 0.792,0.521 1.271,0.99 true 1.615,1.302 1.75,1.771 true 1.375,0.5 1.469,0.979 true 2.052,0.49 1.646,0.969 true 1.406,1.26 0.781,1.198 true 1.406,1.458 0.844,1.781 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 0.552,0.354 1.01,0.552 0.458,0.198 10 false MRF 1.563,1.823 2.021,2.021 0.458,0.198 10 false MRFG 2,0.323 2.458,0.521 0.458,0.198 10 false MSN 1.208,0.344 1.667,0.542 0.458,0.198 10 false MSNG 0.438,1.115 0.896,1.313 0.458,0.198 10 false MCS 0.615,1.833 1.073,2.031 0.458,0.198 10 false MCSG 0.24,0.688 0.698,0.885 0.458,0.198 10 false C1
*1 Component without harness connected
(Motor Resolver (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C1-6 (MRF) - C1-9 (MRFG) Power switch off 9.0 to 15.0 Ω
C1-4 (MSN) - C1-5 (MSNG) Power switch off 16.5 to 28.5 Ω
C1-10 (MCS) - C1-14 (MCSG) Power switch off 18.5 to 30.5 Ω


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F).)


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C1-6 (MRF) - Body ground and other terminals (except C1-9 (MRFG)) Power switch off 1 MΩ or higher
C1-9 (MRFG) - Body ground and other terminals (except C1-6 (MRF)) Power switch off 1 MΩ or higher
C1-4 (MSN) - Body ground and other terminals (except C1-5 (MSNG)) Power switch off 1 MΩ or higher
C1-5 (MSNG) - Body ground and other terminals (except C1-4 (MSN)) Power switch off 1 MΩ or higher
C1-10 (MCS) - Body ground and other terminals (except C1-14 (MCSG)) Power switch off 1 MΩ or higher
C1-14 (MCSG) - Body ground and other terminals (except C1-10 (MCS)) Power switch off 1 MΩ or higher



c.

Reconnect the resolver connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG