The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
for NICKEL METAL HYDRIDE BATTERY:
for LITHIUM-ION BATTERY:
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
1. PERFORM RESOLVER INITIALIZATION
If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.
for NICKEL METAL HYDRIDE BATTERY:
for LITHIUM-ION BATTERY:
2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
3.INSTALL ENGINE HANGERS
82121
4.DISCONNECT ENGINE WIRE
Disconnect the motor revolution sensor wire connector.
| *a | Motor Revolution Sensor Wire Connector | *b | Shift Lever Position Sensor |
| *c | Motor Temperature Sensor Connector | - | - |
Disconnect the shift lever position sensor connector.
After disconnecting the engine wire, cover the connector of the shift lever position sensor with tape (non-residue type) or equivalent to prevent the entry of foreign matter or water.
Disconnect the motor temperature sensor connector.
Remove the 2 bolts.
Disengage the 2 clamps to disconnect the engine wire from the hybrid vehicle transaxle assembly.
821H2
5.DISCONNECT HV AIR CONDITIONING WIRE
Remove the bolt.
Disengage the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.
28193
6.REMOVE STARTER HOLE INSULATOR
Remove the 2 bolts and starter hole insulator from the engine assembly.
11363A
7.REMOVE FLYWHEEL HOUSING SIDE COVER
Remove the flywheel housing side cover from the engine assembly.
8.REMOVE ENGINE ASSEMBLY
Remove the 7 bolts and engine assembly from the hybrid vehicle transaxle assembly.
To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.
To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during hybrid vehicle transaxle assembly removal and installation.
51201
9.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.
12364B
10.REMOVE NO. 2 ENGINE MOVING CONTROL ROD
Remove the 4 bolts and No. 2 engine moving control rod from the hybrid vehicle transaxle assembly.
G1148
11.REMOVE MOTOR CABLE
G125A
12.REMOVE MOTOR COOLING COOLER
Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.
Remove the bolt and No. 1 oil cooler tube clamp from the hose bracket.
Remove the union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.
Remove the 3 bolts and motor cooling cooler with No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.
Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.
G1251B
13.REMOVE NO. 1 MOTOR COOLING PIPE
Loosen the flare nut of the No. 1 motor cooling pipe and disconnect the No. 1 motor cooling pipe from the union.
Remove the bolt, No. 1 oil cooler tube clamp and No. 1 motor cooling pipe from the hose bracket.
44781E
14.REMOVE HOSE BRACKET
Remove the 2 bolts and hose bracket from the hybrid vehicle transaxle assembly.
33823
15.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.
16.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 2 bolts and 2 wire harness clamp brackets from the hybrid vehicle transaxle assembly.
17.REMOVE TRANSAXLE HOUSING PLUG
Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.