The shift lever position sensor sends 7 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses these signals to detect the shift lever position (P, R, N, D or B). The hybrid vehicle control ECU also uses this information to determine the intended direction of travel (forward or reverse).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P070562 | Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure | Shift sensor circuit malfunction (abnormal pattern)
A malfunction in the P, R, N, D or B circuit is detected based on the shift sensor input pattern. (1 trip detection logic) |
·
Wire harness or connector ·
Shift lever position sensor ·
Hybrid vehicle control ECU |
Does not come on | Master Warning:
Comes on |
| DTC No. | ECU Data List |
|---|---|
| P070562 | ·
Shift Position Sensor (PNB) ·
Shift Position Sensor (PR) ·
Shift Position Sensor (DB2) ·
Shift Position Sensor (DB1) ·
Shift Position Sensor (N) ·
Shift Position Sensor (R) ·
Shift Position Sensor (P) ·
Shift Position |
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (IG).
Slowly move the shift lever from P to B then back to P.
Connect the GTS the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Position Sensor (PNB), Shift Position Sensor (PR), Shift Position Sensor (DB2), Shift Position Sensor (DB1), Shift Position Sensor (N), Shift Position Sensor (R), Shift Position Sensor (P).
| Tester Display |
|---|
| Shift Position Sensor (PNB) |
| Shift Position Sensor (PR) |
| Shift Position Sensor (DB1) |
| Shift Position Sensor (DB2) |
| Shift Position Sensor (N) |
| Shift Position Sensor (R) |
| Shift Position Sensor (P) |
While slowly moving the shift lever from P to B, then back to P, read the Data List (Shift Sensor SW) displayed on the GTS.
Be sure to move the shift lever slowly.
| ECU Data List | Shift Position | ||||
| P | R | N | D | B | |
| Shift Position Sensor (P) | ON | OFF | OFF | OFF | OFF |
| Shift Position Sensor (R) | OFF | ON | OFF | OFF | OFF |
| Shift Position Sensor (PR) | ON | ON | OFF | OFF | OFF |
| Shift Position Sensor (N) | OFF | OFF | ON | OFF | OFF |
| Shift Position Sensor (DB1) | OFF | OFF | OFF | ON | ON |
| Shift Position Sensor (DB2) | OFF | OFF | OFF | ON | ON |
| Shift Position Sensor (PNB) | ON | OFF | ON | OFF | ON |
Check for DTCs.
DTC P070562 is not output.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
NG
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-21 (P) - Body ground | Power switch on (IG)
Shift lever in P |
6 to 14 V |
| Power switch on (IG)
Shift lever in any position except P |
0 to 1.5 V | |
| A48-15 (R) - Body ground | Power switch on (IG)
Shift lever in R |
6 to 14 V |
| Power switch on (IG)
Shift lever in any position except R |
0 to 1.5 V | |
| A48-17 (PR) - Body ground | Power switch on (IG)
Shift lever in P or R |
6 to 14 V |
| Power switch on (IG)
Shift lever in any position except P or R |
0 to 1.5 V | |
| A48-20 (N) - Body ground | Power switch on (IG)
Shift lever in N |
6 to 14 V |
| Power switch on (IG)
Shift lever in any position except N |
0 to 1.5 V | |
| A48-26 (DB1) - Body ground | Power switch on (IG)
Shift lever in D or B |
6 to 14 V |
| Power switch on (IG)
Shift lever in any position except D or B |
0 to 1.5 V | |
| A48-14 (DB2) - Body ground | Power switch on (IG)
Shift lever in D or B |
6 to 14 V |
| Power switch on (IG)
Shift lever in any position except D or B |
0 to 1.5 V | |
| A48-34 (PNB) - Body ground | Power switch on (IG)
Shift lever in P, N or B |
6 to 14 V |
| Power switch on (IG)
Shift lever in any position except P, N or B |
0 to 1.5 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
NG
Disconnect the shift lever position sensor connector.
Click hereDrivetrain>P610 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER POSITION SENSOR>REMOVAL
Turn the power switch on (IG).
| *a | Front view of wire harness connector
(to Shift Lever Position Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C36-7 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
Turning the power switch on (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Reconnect the shift lever position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the shift lever position sensor connector.
| *a | Component without harness connected
(Shift Lever Position Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C36-7 (+B) - C36-3 (PR) | Shift lever in P | Below 1 Ω |
| C36-7 (+B) - C36-4 (PNB) | Below 1 Ω | |
| C36-7 (+B) - C36-8 (P) | Below 1 Ω | |
| C36-7 (+B) - C36-1 (DB1), C36-2 (N), C36-6 (DB2) and C36-9 (R) | 10 kΩ or higher | |
| C36-7 (+B) - C36-3 (PR) | Shift lever in R | Below 1 Ω |
| C36-7 (+B) - C36-9 (R) | Below 1 Ω | |
| C36-7 (+B) - C36-1 (DB1), C36-2 (N), C36-4 (PNB), C36-6 (DB2) and C36-8 (P) | 10 kΩ or higher | |
| C36-7 (+B) - C36-2 (N) | Shift lever in N | Below 1 Ω |
| C36-7 (+B) - C36-4 (PNB) | Below 1 Ω | |
| C36-7 (+B) - C36-1 (DB1), C36-3 (PR), C36-6 (DB2), C36-8 (P) and C36-9 (R) | 10 kΩ or higher | |
| C36-7 (+B) - C36-1 (DB1) | Shift lever in D | Below 1 Ω |
| C36-7 (+B) - C36-6 (DB2) | Below 1 Ω | |
| C36-7 (+B) - C36-2 (N), C36-3 (PR), C36-4 (PNB), C36-8 (P) and C36-9 (R) | 10 kΩ or higher | |
| C36-7 (+B) - C36-1 (DB1) | Shift lever in B | Below 1 Ω |
| C36-7 (+B) - C36-4 (PNB) | Below 1 Ω | |
| C36-7 (+B) - C36-6 (DB2) | Below 1 Ω | |
| C36-7 (+B) - C36-2 (N), C36-3 (PR), C36-8 (P) and C36-9 (R) | 10 kΩ or higher |
Terminal No.5 on the component side connector is empty.
Reconnect the shift lever position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the shift lever position sensor connector.
Disconnect the hybrid vehicle control ECU connector.
| *a | Front view of wire harness connector
(to Shift Lever Position Sensor) |
| *b | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C36-7 (+B) - A48-1 (PSFT) | Power switch off | Below 1 Ω |
| C36-7 (+B) or A48-1 (PSFT) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the hybrid vehicle control ECU connector.
Reconnect the shift lever position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG