This DTC indicates that the hybrid vehicle control ECU detected an instantaneous interruption in +B power source voltage.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P06881F | ECM/PCM Power Relay Sense Circuit Intermittent | When the power switch is on (READY), the hybrid vehicle control ECU is reset due to an instantaneous interruption of power source.
(1 trip detection logic) |
·
Wire harness or connector ·
Hybrid vehicle control ECU |
Does not come on | Master Warning:
Comes on |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY) and wait for 30 seconds or more.
(If the DTC is not output, drive the vehicle on urban roads according to the freeze frame data item "Vehicle Speed" for approximately 5 minutes.)
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Confirm whether the auxiliary battery terminals have been disconnected recently.
| Result | Proceed to |
|---|---|
| Terminals have been disconnected. | A |
| Terminals have not been disconnected. | B |
A
B
Turn the power switch on (READY) from off.
Check whether the master warning is on or off.
| Result | Proceed to |
|---|---|
| Master warning on. | A |
| Master warning off. | B |
DTC P06881F may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the power switch is turned off and then on (READY) again. In this case, clear the DTCs to complete the inspection.
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read and record the DTCs and freeze frame data.
Clear the DTCs and freeze frame data.
Turn the power switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC P06881F is output again. | A |
| DTCs other than P06881F are also output. | B |
Turn the power switch off.
A
B
Check the connection of the auxiliary battery terminal.
The terminal is connected securely and there is no contact problem.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IGCT relay from the No. 1 engine room relay block.
Disconnect the hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 1 Engine Room Relay Block | - | - |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
*b | IGCT Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-4 (+B1) - 5 (IGCT relay holder) | Power switch off | Below 1 Ω |
| A49-1 (+B2) - 5 (IGCT relay holder) | Power switch off | Below 1 Ω |
Reconnect the hybrid vehicle control ECU connector.
Install the IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for intermittent problems.
Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.
When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.
| Result | Proceed to |
|---|---|
| Problem symptom does not recur. | A |
| Problem symptom recurs. | B |
A
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
B