Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404406 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0AE415  Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open Open or short to +B in SMRP circuit:
Primary circuit of SMRP is malfunctioning.
(2 trip detection logic)
·

Wire harness or connector

·

HV battery junction block assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0AE415
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid Battery Voltage

·

SMRP Status

·

SMRB Status

·

SMRG Status

·

SMRP Control Status

·

SMRB Control Status

·

SMRG Control Status

·

Boosting Converter Shutdown Status

·

Generator Inverter Shutdown Status

·

Motor Inverter Shutdown Status



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (READY) and wait for 30 seconds or more.

6.

Turn the power switch off and wait for 60 seconds or more.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

If DTC P0AE415 is output, the power switch cannot be turned on (READY).


PROCEDURE

1.READ VALUE USING GTS (SMRP STATUS)
a.

Connect the GTS to the DLC3


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / SMRP Status.

Powertrain > Hybrid Control > Data List
Tester Display
SMRP Status
50003 397 52

d.

Read the Data List.

Standard:
Tester Display Condition Specified Condition
SMRP Status Power switch on (IG) OFF



e.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

5.CHECK HARNESS AND CONNECTOR (SMRP VOLTAGE)
2.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (SMRP VOLTAGE)
a.

Turn the power switch on (IG).


b.
A389500C08
1.802,0.833 2.302,1.083 0.5,0.25 2.333,2.417 2.104,1.719 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 2.188,2.458 2.75,2.625 0.563,0.167 10 false SMRP 1.979,0.854 2.542,1.021 0.563,0.167 10 false F2
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F2-3 (SMRP) - Body ground Power switch on (IG) Below 1 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

NG

CONNECT SECURELY

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A389503C04
1.792,0.583 2.292,0.833 0.5,0.25 2.458,2.833 2.115,2.417 true 0.271,0.5 0.583,0.656 0.313,0.156 10 false *a 2.365,2.885 2.948,3.052 0.583,0.167 10 false SMRP 1.958,0.604 2.271,0.802 0.313,0.198 10 false F2
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-3 (SMRP) - Body ground Power switch off 140 to 290 Ω



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
8.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376111N04
0.99,0.896 1.385,1.135 0.396,0.24 1.031,0.927 1.354,1.115 0.323,0.188 10 true M42

Disconnect the HV battery junction block assembly connector.


d.

Disconnect the hybrid vehicle control ECU connector.


e.

Turn the power switch on (IG).


f.
A389514C05
1.813,0.25 2.313,0.5 0.5,0.25 0.5,3.417 1,3.667 0.5,0.25 2.5,2.5 2.125,2.042 true 1.854,3.625 2.313,4.042 true 0.271,0.271 0.583,0.427 0.313,0.156 10 false *a 0.438,2.917 0.75,3.073 0.313,0.156 10 false *b 2.375,2.531 2.938,2.698 0.563,0.167 10 false SMRP 2.177,4.094 2.74,4.26 0.563,0.167 10 false SMRP 0.615,3.448 1.177,3.615 0.563,0.167 10 false M42 1.979,0.271 2.542,0.438 0.563,0.167 10 false F2
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F2-3 (SMRP) and M42-2 (SMRP) - Body ground and other terminals Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector and the HV battery junction block assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Reconnect the hybrid vehicle control ECU connector.


i.

Reconnect the HV battery junction block assembly connector.


j.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376111N04
0.99,0.896 1.385,1.135 0.396,0.24 1.031,0.927 1.354,1.115 0.323,0.188 10 true M42

Disconnect the HV battery junction block assembly connector.


d.

Disconnect the hybrid vehicle control ECU connector.


e.
A389514C05
1.813,0.25 2.313,0.5 0.5,0.25 0.5,3.417 1,3.667 0.5,0.25 2.5,2.5 2.125,2.042 true 1.854,3.625 2.313,4.042 true 0.271,0.271 0.583,0.427 0.313,0.156 10 false *a 0.438,2.917 0.75,3.073 0.313,0.156 10 false *b 2.375,2.531 2.938,2.698 0.563,0.167 10 false SMRP 2.177,4.094 2.74,4.26 0.563,0.167 10 false SMRP 0.615,3.448 1.177,3.615 0.563,0.167 10 false M42 1.979,0.271 2.542,0.438 0.563,0.167 10 false F2
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F2-3 (SMRP) - M42-2 (SMRP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F2-3 (SMRP) and M42-2 (SMRP) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the hybrid vehicle control ECU connector.


g.

Reconnect the HV battery junction block assembly connector.


h.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

OK

12.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the HV battery junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

A378136C63
3.844,1 4.208,1.208 0.365,0.208 3.385,1.188 3.208,1.354 true 3.5,1.188 3.667,1.365 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 3.885,1.021 4.198,1.177 0.313,0.156 10 false M42 3.073,1.396 3.427,1.563 0.354,0.167 10 true GND 3.531,1.396 3.99,1.563 0.458,0.167 10 true SMRP
*a Component without harness connected
(HV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M42-2 (SMRP) - M42-3 (GND) -40 to 80°C (-40 to 176°F) 140 to 290 Ω



e.

Reconnect the HV battery junction block assembly connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

NG