Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404409 MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P0A7A73  Generator Inverter Actuator Stuck Closed  


DTC SUMMARY

MALFUNCTION DESCRIPTION


This DTC is stored when a short is detected in the inverter with converter assembly (generator inverter) or the hybrid vehicle transaxle assembly (generator (MG1)). The cause of this malfunction may be one of the following:

Internal inverter malfunction

Generator inverter internal circuit malfunction


Hybrid vehicle transaxle assembly (generator (MG1)) malfunction
·

Open or short circuit

·

Damage from iron particles or other foreign objects



DESCRIPTION

For a description of the inverter.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>P0D2D16

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A7A73 Generator Inverter Actuator Stuck Closed Current flow to any phase of the generator (MG1) exceeds the threshold after the generator inverter is shut down due to a DTC indicating a generator inverter malfunction (overheating, overcurrent or circuit malfunction) being stored.
(1 trip detection logic)
·

Inverter with converter assembly

·

Motor cable

·

Hybrid vehicle transaxle assembly


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Turn the power switch on (READY) and wait for 5 seconds or more.

HINT:

Check that there are no abnormalities (abnormal sounds, coolant leaks, etc.).


8.

Drive the vehicle for approximately 10 minutes mainly using the engine. During the road test, check the Data List item "Generator Inverter Temperature" to prevent the generator inverter from overheating.

NOTICE:

As the state of charge of the HV battery may be low after driving in fail-safe mode, it will automatically be charged for 5 to 10 minutes with power switch on (READY) after repairs have been performed.


9.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C56
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

DTC P0A7A73 is stored after DTC P0A7A9E and/or P1C5F19 is stored. After troubleshooting and repairing the malfunction which caused DTC P0A7A73 to be stored, be sure to troubleshoot the other DTCs.

·

Depending on the conditions in which the vehicle is being operated when a short circuit occurs in the inverter with converter assembly, the hybrid vehicle transaxle assembly may be affected. As this DTC is stored if a short circuit occurs in the inverter with converter assembly, it is necessary to perform a road test to check the hybrid vehicle transaxle assembly. If problems are found, replace the malfunctioning parts.

·

After completing the repair, including the repair of previously output DTCs, drive the vehicle at a speed of approximately 40 km/h (25 mph) for 1 minute and check that DTC P0A92000 is not output. If DTC P0A92000 is output, replace the hybrid vehicle transaxle assembly.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0A7A73 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Malfunction Content Relevant DTC
Insulation Malfunction P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure

HINT:
·

P0A7A73 may be output as a result of the malfunctions indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





e.

Turn the power switch off.



A

2.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR (MG1))

B

2.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR (MG1))

OK

3.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

4.CHECK MOTOR CABLE (FOR MG1)
3.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

13.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK MOTOR CABLE (FOR MG1)

OK

5.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

7.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR (MG1))
5.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

6.REPLACE INVERTER WITH CONVERTER ASSEMBLY
6.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

13.CHECK DTC OUTPUT (HYBRID CONTROL)
7.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR (MG1))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the motor cable from the hybrid vehicle transaxle assembly.


c.
A376650E24
1.438,0.208 1.792,0.469 0.354,0.26 1.667,0.948 1.99,1.458 true 1.521,0.958 1.563,1.427 true 1.385,0.958 1.167,1.458 true 1.51,0.24 1.719,0.427 0.208,0.188 10 true i1 1.927,1.51 2.083,1.708 0.156,0.198 10 true W 1.125,1.49 1.281,1.688 0.156,0.198 10 true V 1.542,1.5 1.698,1.698 0.156,0.198 10 true U

Check the generator (MG1) for an interphase short using a milliohmmeter.

i.

Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the generator (MG1) temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle has been stopped.


Standard Resistance:
Tester Connection Condition Specified Condition
i1-3 (W) - i1-2 (U) Power switch off 105.4 to 116.4 mΩ
i1-2 (U) - i1-1 (V) Power switch off 105.4 to 116.4 mΩ
i1-3 (W) - i1-1 (V) Power switch off 105.4 to 116.4 mΩ


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68° F).

R20 = Rt / {1 + 0.00393 X (T - 20)}


The calculation is based on the following:

R20: Resistance at 20°C (68° F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (° C)





d.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
i1-3 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
i1-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
i1-1 (V) - Body ground and shield ground Power switch off 100 MΩ or higher



e.

Connect the motor cable.


Result:
Proceed to
OK
NG



OK

8.REPLACE MOTOR CABLE

NG

10.REPLACE MOTOR CABLE
8.REPLACE MOTOR CABLE

NEXT

9.REPLACE INVERTER WITH CONVERTER ASSEMBLY
9.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

13.CHECK DTC OUTPUT (HYBRID CONTROL)
10.REPLACE MOTOR CABLE

NEXT

11.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
11.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

12.REPLACE INVERTER WITH CONVERTER ASSEMBLY
12.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

13.CHECK DTC OUTPUT (HYBRID CONTROL)
13.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A7A73.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Relevant DTC
P0A7A9E Generator Inverter Stuck On
P1C5F19 Generator Inverter Circuit Current Above Threshold


NOTICE:

DTC P0A7A73 is stored after DTC P0A7A9E and/or P1C5F19 is stored. After troubleshooting and repairing the malfunction which caused DTC P0A7A73 to be stored, be sure to troubleshoot the other DTCs.



Result:
Proceed to
NEXT



NEXT