Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404409 MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P31241F  Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent  P312487  Lost Communication between Drive Motor "A" and HV ECU Missing Message  


DESCRIPTION

The motor generator control ECU, which is built into the inverter with converter assembly, controls the motor (MG2) based on commands from the hybrid vehicle control ECU.

The motor generator control ECU (MG ECU) monitors communication data and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P31241F Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard) detected when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Does not come on
P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C56
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Motor Generator > Clear DTCs
50002 395

f.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (MOTOR GENERATOR CONTROL)
2.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (MOTOR GENERATOR CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Motor Generator / Utility / Diagnosis Related Information.

Powertrain > Motor Generator > Utility
Tester Display
Diagnosis Related Information
50005 395 56

d.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.

Powertrain > Motor Generator > Trouble Codes
50001 395

e.

Check for DTCs.

Result:
Result Proceed to
P31241F or P312487 is listed in Diagnosis Related Information or DTC P31241F or P312487 is output. A
P31241F and P312487 is not listed in Diagnosis Information and DTC P31241F and P312487 is not output. B



f.

Turn the power switch off.



A

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

B

3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A394772C12
1.167,0.333 1.667,0.583 0.5,0.25 1.75,0.333 2.25,0.583 0.5,0.25 1.531,1.313 1.302,1.896 true 1.573,1.323 1.823,1.885 true 1.833,1.094 2.656,1.927 true 0.052,0.063 0.365,0.219 0.313,0.156 10 false *a 1.281,0.375 1.594,0.531 0.313,0.156 10 false A48 1.917,0.375 2.229,0.531 0.313,0.156 10 false F2 0.844,1.823 1.344,2 0.5,0.177 10 false HMCH 1.865,1.813 2.365,1.99 0.5,0.177 10 false HMCL 2.708,1.844 3.208,2.021 0.5,0.177 10 false E1 0.219,2.938 0.573,3.115 0.354,0.177 10 false CH1 0.219,3.677 0.573,3.854 0.354,0.177 10 false CH2 2.813,3.479 3.167,3.656 0.354,0.177 10 false GND 2.823,4.042 3.177,4.219 0.354,0.177 10 false GND
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the waveform.

Item Contents
Tester Connection CH1: A48-31 (HMCH) - F2-6 (E1)
CH2: A48-30 (HMCL) - F2-6 (E1)
Equipment Setting 1 V/DIV., 200 μs./DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


HINT:
·

Perform this inspection with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

B

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

5.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the hybrid vehicle control ECU connector.


c.

Disconnect the inverter with converter assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A389523C58
0.333,0.833 0.833,1.083 0.5,0.25 1.177,2.271 1.677,2.521 0.5,0.25 0.833,1.667 1.375,1.396 true 2,4.417 1.604,4.198 true 1.531,4.208 1.083,4.417 true 2,2 1.542,1.396 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.188,2.167 0.5,2.323 0.313,0.156 10 false *b 0.531,1.688 1.094,1.844 0.563,0.156 10 false HMCL 1.844,2.031 2.406,2.188 0.563,0.156 10 false HMCH 0.792,4.448 1.354,4.604 0.563,0.156 10 false HMCH 1.906,4.438 2.469,4.594 0.563,0.156 10 false HMCL 0.458,0.865 0.76,1.052 0.302,0.188 10 false C65 1.302,2.302 1.604,2.49 0.302,0.188 10 false A48
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C65-20 (HMCH) or A48-31 (HMCH) - Body ground and other terminals Power switch on (IG) Below 1 V
C65-19 (HMCL) or A48-30 (HMCL) - Body ground and other terminals Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU and inverter with converter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C65-20 (HMCH) - A48-31 (HMCH) Power switch off Below 1 Ω
C65-19 (HMCL) - A48-30 (HMCL) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C65-20 (HMCH) or A48-31 (HMCH) - Body ground and other terminals Power switch off 10 kΩ or higher
C65-19 (HMCL) or A48-30 (HMCL) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured resistance is as specified.

Check that each connector between the inverter with converter assembly and hybrid vehicle control ECU is not loose or disconnected.



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Reconnect the inverter with converter assembly connector.


k.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

7.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A389502C12
1.167,0.667 1.667,0.917 0.5,0.25 1.531,2.646 1.24,3.125 true 1.594,2.635 1.927,3.146 true 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 1.281,0.698 1.635,0.875 0.354,0.177 10 false A48 0.771,3.042 1.25,3.219 0.479,0.177 10 false HMCH 1.99,3.042 2.469,3.219 0.479,0.177 10 false HMCL
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-31 (HMCH) - A48-30 (HMCL) Power switch off 80 to 170 Ω



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG