Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404410 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P0A9B11  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground  P0A9B15  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open  P0AC511  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground  P0AC515  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open  P0ACA11  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground  P0ACA15  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open  P0AE811  Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Ground  P0AE815  Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Auxiliary Battery or Open  P0BC211  Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Ground  P0BC215  Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Auxiliary Battery or Open  P0C3311  Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Ground  P0C3315  Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

The battery temperature sensors are provided at 6 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery ECU assembly uses the battery temperature sensors to detect the HV battery temperature. Based on the results of this detection, the battery ECU assembly controls the blower fan. (The blower fan starts when the HV battery temperature rises above a predetermined level.)

Temperature Sensor Identification Cross Reference Table:
DTC Title Sensor Battery Temperature Sensor GTS Display
A 0 1
B 1 2
C 2 3
D 3 4
E 4 5
F 5 6


HINT:

Use the reference table above to determine which battery temperature sensor corresponds to each DTC. For example, sensor A in the DTC title column is battery temperature sensor 0. This sensor is displayed as Hybrid Battery Temperature 1 in the Data List.


A171806E05
1.896,0.031 2.635,0.188 0.74,0.156 10 false Reference: 2.167,0.354 2.427,0.5 0.26,0.146 10 false 250 2.167,0.677 2.427,0.823 0.26,0.146 10 false 200 2.167,0.979 2.427,1.125 0.26,0.146 10 false 150 2.177,1.271 2.438,1.417 0.26,0.146 10 false 100 2.25,1.583 2.438,1.729 0.188,0.146 10 false 50 2.333,1.896 2.438,2.042 0.104,0.146 10 false 0 3.271,2.25 3.375,2.396 0.104,0.146 10 false 0 2.573,2.25 2.802,2.417 0.229,0.167 10 false -40 2.917,2.25 3.146,2.417 0.229,0.167 10 false -20 3.521,2.25 3.698,2.417 0.177,0.167 10 false 20 3.813,2.25 3.99,2.417 0.177,0.167 10 false 40 4.094,2.25 4.271,2.417 0.177,0.167 10 false 60 4.396,2.25 4.573,2.417 0.177,0.167 10 false 80 4.646,2.25 4.906,2.417 0.26,0.167 10 false 100 3.177,2.458 3.448,2.604 0.271,0.146 10 false (32) 2.531,2.448 2.865,2.615 0.333,0.167 10 false (-40) 2.906,2.448 3.167,2.615 0.26,0.167 10 false (-4) 3.458,2.448 3.729,2.615 0.271,0.167 10 false (68) 3.708,2.448 4.073,2.615 0.365,0.167 10 false (104) 4.031,2.448 4.375,2.615 0.344,0.167 10 false (140) 4.354,2.448 4.708,2.615 0.354,0.167 10 false (176) 4.677,2.448 5.021,2.615 0.344,0.167 10 false (212) 5.094,2.24 5.365,2.438 0.271,0.198 10 false (°C) 5.094,2.448 5.427,2.646 0.333,0.198 10 false (°F) 1.823,0.375 2.115,0.573 0.292,0.198 10 false (kΩ) 1.24,1.146 1.969,1.333 0.729,0.188 10 false Resistance 5.531,2.24 6.875,2.427 1.344,0.188 10 false Battery Temperature 2.604,0.042 5.698,0.219 3.094,0.177 10 false Battery Temperature Sensor Characteristic Graph

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9B11 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0A9B15 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AC511 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AC515 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0ACA11 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0ACA15 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AE811 Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AE815 Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0BC211 Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0BC215 Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0C3311 Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0C3315 Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A9B11 Hybrid Battery Temperature 1 to 6
P0A9B15
P0AC511
P0AC515
P0ACA11
P0ACA15
P0AE811
P0AE815
P0BC211
P0BC215
P0C3311
P0C3315

HINT:
·

After checking for the above DTCs, check the hybrid system Data List item "Hybrid Battery Temperature" using the GTS.

Temperature Displayed Malfunction
Below -45°C (-49°F) Open or +B short circuit
95°C (203°F) or more GND short circuit

·

If the vehicle as is left as is for 24 hours, the value of "Hybrid Battery Temperature" will be almost the same as the ambient temperature.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 10 seconds or more.

7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A409009E05
0.667,2.563 3.49,2.927 2.823,0.365 10 false z17 0.74,8.375 3.323,8.646 2.583,0.271 10 false No. 2 HV Supply Stack Sub-assembly 1.833,0.479 3.438,1 1.604,0.521 10 false Battery Current Sensor 4.958,8.458 6.99,8.729 2.031,0.271 10 false z23 5.01,3.104 5.385,3.552 0.375,0.448 10 false 22 5.292,3.115 5.667,3.563 0.375,0.448 10 false TB0 5.292,3.531 5.667,3.979 0.375,0.448 10 false GB0 5.292,7.552 5.667,8 0.375,0.448 10 false TB5 5.281,7.969 5.656,8.417 0.375,0.448 10 false GB5 5,3.531 5.375,3.979 0.375,0.448 10 false 10 5.031,7.552 5.406,8 0.375,0.448 10 false 17 5.083,7.969 5.458,8.417 0.375,0.448 10 false 5 5.302,1.021 5.677,1.469 0.375,0.448 10 false VIB 5.292,1.375 5.667,1.823 0.375,0.448 10 false IB0 5.292,1.75 5.667,2.198 0.375,0.448 10 false IB1 5.281,2.094 5.656,2.542 0.375,0.448 10 false GIB 5.021,1.021 5.396,1.469 0.375,0.448 10 false 24 5.021,1.375 5.396,1.823 0.375,0.448 10 false 23 5.021,2.083 5.396,2.531 0.375,0.448 10 false 12 5.021,1.75 5.396,2.198 0.375,0.448 10 false 11 1.594,3.385 3.844,4.031 2.25,0.646 10 false Battery Temperature Sensor 0 5.292,3.844 5.667,4.292 0.375,0.448 10 false TB1 5.281,4.26 5.656,4.708 0.375,0.448 10 false GB1 5.292,4.677 5.667,5.125 0.375,0.448 10 false TB2 5.292,5.094 5.667,5.542 0.375,0.448 10 false GB2 5.292,6.01 5.667,6.458 0.375,0.448 10 false TB3 5.292,6.427 5.667,6.875 0.375,0.448 10 false GB3 5.292,6.813 5.667,7.26 0.375,0.448 10 false TB4 5.292,7.229 5.667,7.677 0.375,0.448 10 false GB4 5,3.844 5.375,4.292 0.375,0.448 10 false 21 5.073,4.26 5.448,4.708 0.375,0.448 10 false 9 5.01,4.677 5.385,5.125 0.375,0.448 10 false 20 5.083,5.094 5.458,5.542 0.375,0.448 10 false 8 5.031,6.01 5.406,6.458 0.375,0.448 10 false 19 5.104,6.438 5.479,6.885 0.375,0.448 10 false 7 5.031,6.813 5.406,7.26 0.375,0.448 10 false 18 5.083,7.229 5.458,7.677 0.375,0.448 10 false 6 1.594,4.115 3.844,4.76 2.25,0.646 10 false Battery Temperature Sensor 1 1.594,4.948 3.844,5.594 2.25,0.646 10 false Battery Temperature Sensor 2 1.604,6.302 3.854,6.948 2.25,0.646 10 false Battery Temperature Sensor 3 1.604,7.115 3.854,7.76 2.25,0.646 10 false Battery Temperature Sensor 4 1.615,7.865 3.865,8.51 2.25,0.646 10 false Battery Temperature Sensor 5 3.115,1.01 3.49,1.458 0.375,0.448 10 false VIB 3.135,1.375 3.51,1.823 0.375,0.448 10 false IB0 3.135,1.75 3.51,2.198 0.375,0.448 10 false IB1 3.104,2.083 3.479,2.531 0.375,0.448 10 false GIB 3.49,1.01 3.865,1.458 0.375,0.448 10 false 1 3.5,1.75 3.875,2.198 0.375,0.448 10 false 2 3.5,1.375 3.875,1.823 0.375,0.448 10 false 4 3.5,2.083 3.875,2.531 0.375,0.448 10 false 3 1.24,5.688 3.823,5.958 2.583,0.271 10 false No. 1 HV Supply Stack Sub-assembly 3.771,1.01 4.146,1.458 0.375,0.448 10 false 1 3.781,1.75 4.156,2.198 0.375,0.448 10 false 2 3.781,2.083 4.156,2.531 0.375,0.448 10 false 6 3.781,1.375 4.156,1.823 0.375,0.448 10 false 7 4.146,1 4.521,1.448 0.375,0.448 10 false 1 4.146,1.375 4.521,1.823 0.375,0.448 10 false 7 4.146,1.75 4.521,2.198 0.375,0.448 10 false 2 4.146,2.073 4.521,2.521 0.375,0.448 10 false 6 4.156,6.01 4.531,6.458 0.375,0.448 10 false 10 3.708,6.01 4.083,6.458 0.375,0.448 10 false 10 4.177,6.427 4.552,6.875 0.375,0.448 10 false 5 3.781,6.427 4.156,6.875 0.375,0.448 10 false 5 4.177,6.813 4.552,7.26 0.375,0.448 10 false 9 3.781,6.813 4.156,7.26 0.375,0.448 10 false 9 4.177,7.229 4.552,7.677 0.375,0.448 10 false 4 3.781,7.229 4.156,7.677 0.375,0.448 10 false 4 4.177,7.563 4.552,8.01 0.375,0.448 10 false 8 3.781,7.563 4.156,8.01 0.375,0.448 10 false 8 4.188,7.969 4.563,8.417 0.375,0.448 10 false 3 3.781,7.969 4.156,8.417 0.375,0.448 10 false 3 3.99,8.354 4.365,8.615 0.375,0.26 10 false A 3.969,2.5 4.344,2.76 0.375,0.26 10 false A 0.958,2.563 3.781,2.927 2.823,0.365 10 false HV Battery Junction Block Assembly 5.24,8.448 6.802,8.688 1.563,0.24 10 false Battery ECU Assembly

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
"P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315" only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid battery system in the table below are output. B
DTCs of hybrid control system in the table below are output. C


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


e.

Turn the power switch off.



A

2.READ VALUE USING GTS (HYBRID BATTERY TEMPERATURE)

B

C

2.READ VALUE USING GTS (HYBRID BATTERY TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Temperature 1 to 6.


d.

Read the Data List.

Powertrain > HV Battery > Data List
Tester Display Measurement Item Range Reference Value Diagnostic Note
Hybrid Battery Temperature 1 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid Battery Temperature 2 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid Battery Temperature 3 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid Battery Temperature 4 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid Battery Temperature 5 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid Battery Temperature 6 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Powertrain > HV Battery > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
Hybrid Battery Temperature 4
Hybrid Battery Temperature 5
Hybrid Battery Temperature 6
50003 398 62,63,64,65,66,67

HINT:

A malfunctioning sensor (battery temperature sensor 0 to 5) can be determined by comparing the output temperature of the 6 battery temperature sensors.


e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)
3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A377561N10
2.375,0.073 2.76,0.333 0.385,0.26 2.458,0.135 2.958,0.531 0.5,0.396 10 false z23

Check the connector connections and contact pressure of the relevant terminals for the battery ECU assembly.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.



d.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

CONNECT SECURELY

4.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11 or P0ACA15" is also output. A
"P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315" is also output. B



A

5.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)

B

6.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
5.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A376391C21
1.542,2.302 1.927,2.552 0.385,0.25 1.167,2.188 1.5,3.073 true 0.615,3.885 1.188,3.406 true 1.188,3.052 0.698,2.656 true 1.354,3.063 0.906,2.458 true 1.073,3.948 1.344,3.406 true 1.438,4.063 1.51,3.406 true 0.229,0.031 0.656,0.333 0.427,0.302 10 false *a 1.333,4.125 1.74,4.458 0.406,0.333 10 false TB2 0.417,2.594 0.823,2.927 0.406,0.333 10 false GB0 1.635,2.344 2.042,2.677 0.406,0.333 10 false z23 0.448,3.906 0.854,4.24 0.406,0.333 10 false TB0 0.948,3.99 1.354,4.323 0.406,0.333 10 false TB1 0.594,2.333 1,2.667 0.406,0.333 10 false GB1 0.865,2.104 1.271,2.438 0.406,0.333 10 false GB2
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).

Tester Connection:
Tester Connection Battery Temperature Sensor
z23-22 (TB0) - z23-10 (GB0) 0
z23-21 (TB1) - z23-9 (GB1) 1
z23-20 (TB2) - z23-8 (GB2) 2


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 to 10°C (32 to 50°F) Power switch off 17.7 to 27.8 kΩ
10 to 20°C (50 to 68°F) Power switch off 12.0 to 18.2 kΩ
20 to 30°C (68 to 86°F) Power switch off 8.22 to 12.2 kΩ
30 to 40°C (86 to 104°F) Power switch off 5.74 to 8.41 kΩ
40 to 50°C (104 to 122°F) Power switch off 4.09 to 5.91 kΩ



e.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z23-22 (TB0) - Body ground and other terminals (except z23-10 (GB0)) Power switch off 10 kΩ or higher
z23-10 (GB0) - Body ground and other terminals (except z23-22 (TB0)) Power switch off 10 kΩ or higher
z23-21 (TB1) - Body ground and other terminals (except z23-9 (GB1)) Power switch off 10 kΩ or higher
z23-9 (GB1) - Body ground and other terminals (except z23-21 (TB1)) Power switch off 10 kΩ or higher
z23-20 (TB2) - Body ground and other terminals (except z23-8 (GB2)) Power switch off 10 kΩ or higher
z23-8 (GB2) - Body ground and other terminals (except z23-20 (TB2)) Power switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value (s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z23-22 (TB0) - Body ground Power switch on (IG) Below 1 V
z23-10 (GB0) - Body ground Power switch on (IG) Below 1 V
z23-21 (TB1) - Body ground Power switch on (IG) Below 1 V
z23-9 (GB1) - Body ground Power switch on (IG) Below 1 V
z23-20 (TB2) - Body ground Power switch on (IG) Below 1 V
z23-8 (GB2) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the battery ECU assembly connector.


l.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

7.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

6.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A376391C22
1.542,2.302 1.927,2.552 0.385,0.25 2.354,2.365 1.927,3.063 true 1.625,3.073 0.896,2.615 true 1.771,3.063 1.135,2.5 true 2.021,4.135 1.802,3.417 true 1.573,4.063 1.646,3.406 true 2.365,4.104 1.938,3.406 true 0.229,0.031 0.656,0.333 0.427,0.302 10 false *a 1.448,4.125 1.854,4.458 0.406,0.333 10 false TB3 0.583,2.51 0.99,2.844 0.406,0.333 10 false GB3 1.635,2.344 2.042,2.677 0.406,0.333 10 false z23 2.292,4.146 2.698,4.479 0.406,0.333 10 false TB5 1.938,4.167 2.344,4.5 0.406,0.333 10 false TB4 0.833,2.354 1.24,2.688 0.406,0.333 10 false GB4 2.438,2.271 2.844,2.604 0.406,0.333 10 false GB5
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 3 to 5).

Tester Connection:
Tester Connection Battery Temperature Sensor
z23-19 (TB3) - z23-7 (GB3) 3
z23-18 (TB4) - z23-6 (GB4) 4
z23-17 (TB5) - z23-5 (GB5) 5


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 to 10°C (32 to 50°F) Power switch off 17.7 to 27.8 kΩ
10 to 20°C (50 to 68°F) Power switch off 12.0 to 18.2 kΩ
20 to 30°C (68 to 86°F) Power switch off 8.22 to 12.2 kΩ
30 to 40°C (86 to 104°F) Power switch off 5.74 to 8.41 kΩ
40 to 50°C (104 to 122°F) Power switch off 4.09 to 5.91 kΩ



e.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z23-19 (TB3) - Body ground and other terminals (except z23-7 (GB3)) Power switch off 10 kΩ or higher
z23-7 (GB3) - Body ground and other terminals (except z23-19 (TB3)) Power switch off 10 kΩ or higher
z23-18 (TB4) - Body ground and other terminals (except z23-6 (GB4)) Power switch off 10 kΩ or higher
z23-6 (GB4) - Body ground and other terminals (except z23-18 (TB4)) Power switch off 10 kΩ or higher
z23-17 (TB5) - Body ground and other terminals (except z23-5 (GB5)) Power switch off 10 kΩ or higher
z23-5 (GB5) - Body ground and other terminals (except z23-17 (TB5)) Power switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value (s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z23-19 (TB3) - Body ground Power switch on (IG) Below 1 V
z23-7 (GB3) - Body ground Power switch on (IG) Below 1 V
z23-18 (TB4) - Body ground Power switch on (IG) Below 1 V
z23-6 (GB4) - Body ground Power switch on (IG) Below 1 V
z23-17 (TB5) - Body ground Power switch on (IG) Below 1 V
z23-5 (GB5) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the battery ECU assembly connector.


l.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

7.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

11.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)
7.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A377566C60
1.521,2.292 1.927,2.573 0.406,0.281 0.448,3.823 0.906,3.406 true 0.375,2.802 0.906,3.073 true 1.625,2.333 2.156,2.75 0.531,0.417 10 false z23 0.198,3.854 0.604,4.125 0.406,0.271 10 false VIB 0.104,2.708 0.51,2.979 0.406,0.271 10 false GIB 0.698,2.083 1.104,2.354 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-24 (VIB) - z23-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

8.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
8.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376519N18
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.74,1.51 0.281,0.177 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A251028C81
2.333,1.135 2.729,1.365 0.396,0.229 1.531,1.094 0.99,0.906 false 1,1.771 1.542,1.583 false 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 0.729,1.719 1.094,1.969 0.365,0.25 10 false GIB 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.427,1.167 2.802,1.469 0.375,0.302 10 false z17
*a Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z17-1(VIB) - z17-3 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


j.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A377612N02
1.198,0.729 1.531,0.969 0.333,0.24 1.25,0.75 1.479,0.958 0.229,0.208 10 true A

Disconnect the No. 2 HV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A376519N18
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.74,1.51 0.281,0.177 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A377603C16
1.51,1.656 1.927,1.875 0.417,0.219 0.74,0.771 1.156,0.99 0.417,0.219 1.844,2.531 2.313,2.344 true 1.844,2.875 2.396,3.01 true 1.083,2.427 1.615,2.531 true 1.135,3.073 1.604,2.885 true 2,0.854 2.583,0.531 true 1.875,0.833 2.365,0.354 true 1.854,1.104 2.323,1.458 true 2,1.083 2.417,1.26 true 1.052,0.063 1.542,0.521 0.49,0.458 10 false *a 1,1.531 1.417,2.021 0.417,0.49 10 false *b 2.479,1.229 2.969,1.688 0.49,0.458 10 false GIB 2.448,0.229 2.938,0.688 0.49,0.458 10 false IB1 2.365,1.417 2.854,1.875 0.49,0.458 10 false IB0 2.625,0.458 3.115,0.917 0.49,0.458 10 false VIB 2.365,2.271 2.823,2.583 0.458,0.313 10 false IB1 0.896,3.031 1.323,3.313 0.427,0.281 10 false GIB 2.448,2.969 2.875,3.188 0.427,0.219 10 false IB0 0.833,2.354 1.323,2.813 0.49,0.458 10 false VIB 1.635,1.688 2.052,2.177 0.417,0.49 10 false z17 0.906,0.792 1.323,1.281 0.417,0.49 10 false A
*a Front view of wire harness connector
(to No. 1 HV Supply Stack Sub-assembly)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A-2 (IB1) - z17-2 (IB1) Power switch off Below 1 Ω
A-6 (GIB) - z17-3 (GIB) Power switch off Below 1 Ω
A-7 (IB0) - z17-4 (IB0) Power switch off Below 1 Ω
A-1 (VIB) - z17-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A-2 (IB1) or z17-2 (IB1) - Body ground and other terminals Power switch off 10 kΩ or higher
A-6 (GIB) or z17-3 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
A-7 (IB0) or z17-4 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
A-1 (VIB) or z17-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


g.

Reconnect the No. 2 HV supply stack sub-assembly connector.


h.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376397N05
1.354,1.26 1.635,1.458 0.281,0.198 1.396,1.271 1.615,1.438 0.219,0.167 10 true A

Disconnect the No. 1 HV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A377579C19
1.75,1.51 2.094,1.708 0.344,0.198 1.677,3.083 2.021,3.281 0.344,0.198 0.844,1.979 1.396,2.073 true 1.646,3.833 1.031,3.479 true 0.667,2.146 1.229,2.146 true 0.969,4.25 1.51,4.125 true 0.99,2.573 1.385,2.354 true 0.646,2.344 1.208,2.344 true 1.656,4.125 1.042,4.49 true 0.885,3.74 1.479,3.896 true 0.875,1.552 1.354,2.01 0.479,0.458 10 false *a 1.333,3.135 1.719,3.531 0.385,0.396 10 false *b 0.615,1.885 1.094,2.344 0.479,0.458 10 false IB1 1.802,1.521 2.281,1.979 0.479,0.458 10 false z23 1.792,3.115 2.271,3.573 0.479,0.458 10 false A 0.802,3.354 1.281,3.813 0.479,0.458 10 false IB1 0.396,2.073 0.875,2.531 0.479,0.458 10 false GIB 0.688,4.188 1.125,4.427 0.438,0.24 10 false GIB 0.781,2.542 1.26,3 0.479,0.458 10 false IB0 0.385,2.281 0.865,2.74 0.479,0.458 10 false VIB 0.781,4.448 1.198,4.667 0.417,0.219 10 false IB0 0.625,3.667 1.104,4.125 0.479,0.458 10 false VIB
*a Rear view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to No. 2 HV Supply Stack Sub-assembly)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z23-11 (IB1) - A-2 (IB1) Power switch off Below 1 Ω
z23-12 (GIB) - A-6 (GIB) Power switch off Below 1 Ω
z23-23 (IB0) - A-7 (IB0) Power switch off Below 1 Ω
z23-24 (VIB) - A-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z23-11 (IB1) or A-2 (IB1) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-12 (GIB) or A-6 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-23 (IB0) or A-7 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-24 (VIB) or A-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the battery ECU assembly connector.


g.

Reconnect the No. 1 HV supply stack sub-assembly connector.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

11.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)

OK

NG