Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404410 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) J

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  ECU Power Source Circuit  


DESCRIPTION

If the power switch is on (IG), the battery ECU assembly applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the IGCT terminals.

WIRING DIAGRAM

A440113E04
0.677,0.688 1.865,1.25 1.188,0.563 10 false IGCT Relay 2.26,0.917 3.698,1.521 1.438,0.604 10 false IGCT NO. 2 4.781,0.729 5.969,1.292 1.188,0.563 10 false IGCT 4.781,1.177 5.969,1.74 1.188,0.563 10 false GND 4.792,1.615 5.979,2.177 1.188,0.563 10 false GND1 4.313,2.094 6.302,2.365 1.99,0.271 10 false z22 4.583,1.073 4.927,1.354 0.344,0.281 10 false 4 4.521,1.5 4.865,1.781 0.344,0.281 10 false 10 4.51,0.604 4.865,0.885 0.354,0.281 10 false 16 2.354,0.604 2.698,0.885 0.344,0.281 10 false 1 2.781,0.604 3.125,0.823 0.344,0.219 10 false 2 4.583,2.094 6.573,2.365 1.99,0.271 10 false Battery ECU Assembly

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A376410C51
1.615,1.927 2.031,2.146 0.417,0.219 0.875,3.104 1.302,2.99 true 0.302,0.146 0.708,0.479 0.406,0.333 10 false *a 1.719,1.969 2.156,2.406 0.438,0.438 10 false z22 0.552,3.094 1.021,3.354 0.469,0.26 10 false IGCT
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z22-16 (IGCT) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)

NG

3.CHECK FUSE (IGCT NO. 2)
2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A376396C44
1.594,1.406 2.021,1.688 0.427,0.281 1.927,2.188 2.688,1.865 true 2.177,2.49 2.802,2.667 true 0.177,0.063 0.573,0.417 0.396,0.354 10 false *a 1.698,1.469 2.094,1.823 0.396,0.354 10 false z22 2.729,1.781 3.125,2.135 0.396,0.354 10 false GND 2.844,2.573 3.302,3.031 0.458,0.458 10 false GND1
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z22-4 (GND) - Body ground Always Below 1 Ω
z22-10 (GND1) - Body ground Always Below 1 Ω



e.

Reconnect the battery ECU assembly connector.


f.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FUSE (IGCT NO. 2)
a.
A452341C01
1.74,1.323 2.688,1.792 true 0.354,0.146 0.667,0.344 0.313,0.198 10 false *1 2.729,1.729 3.042,1.927 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 2 fuse terminals - Body ground Always Below 1 Ω



c.

Install the IGCT NO. 2 fuse to the No. 1 engine room relay block.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A452341C01
1.74,1.323 2.688,1.792 true 0.354,0.146 0.667,0.344 0.313,0.198 10 false *1 2.729,1.729 3.042,1.927 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 1 engine room relay block.


e.

Measure the resistance according to the value(s) in the table below.

A452342C01
4.76,1.354 5.156,1.594 0.396,0.24 4.146,2.51 4.542,2.24 true 0.313,0.073 0.771,0.448 0.458,0.375 10 false *1 2.073,0.667 2.448,1.01 0.375,0.344 10 false *a 4.198,1.354 4.729,1.76 0.531,0.406 10 false *b 4.854,1.385 5.385,1.781 0.531,0.396 10 false z22 3.792,2.479 4.219,2.74 0.427,0.26 10 false IGCT
*1 No. 1 Engine Room Relay Block - -
*a IGCT NO. 2 Fuse Holder *b Rear view of wire harness connector
(to Battery ECU Assembly)


Standard Resistance:
Tester Connection Condition Specified Condition
z22-16 (IGCT) - 2 (IGCT NO. 2 fuse holder) Always Below 1 Ω



f.

Install the IGCT NO. 2 fuse to the No. 1 engine room relay block.


g.

Reconnect the battery ECU assembly connector.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGCT RELAY - IGCT NO. 2 FUSE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IGCT RELAY - IGCT NO. 2 FUSE)
a.
A452343C01
1.76,1.302 2.667,0.938 true 0.521,2.625 1.417,2.052 true 0.292,0.094 0.875,0.552 0.583,0.458 10 false *1 2.729,0.823 3.125,1.208 0.396,0.385 10 false *2 0.365,2.583 0.813,2.906 0.448,0.323 10 false *3
*1 No. 1 Engine Room Relay Block
*2 IGCT NO. 2 Fuse
*3 IGCT Relay


Remove the IGCT NO. 2 fuse and IGCT relay from the No. 1 engine room relay block.


b.
A452344C01
0.208,0.135 0.677,0.729 0.469,0.594 10 false *1 2.573,0.854 3.094,1.406 0.521,0.552 10 false *a 2.563,1.844 3.26,2.281 0.698,0.438 10 false *b
*1 No. 1 Engine Room Relay Block
*a IGCT NO. 2 Fuse Holder
*b IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT relay holder) - 1 (IGCT NO. 2 fuse holder) Always Below 1 Ω



c.

Install the IGCT NO. 2 fuse and IGCT relay to the No. 1 engine room relay block.


Result:
Proceed to
OK
NG



OK

CHECK ECU Power Source Circuit (HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A452341C01
1.74,1.323 2.688,1.792 true 0.354,0.146 0.667,0.344 0.313,0.198 10 false *1 2.729,1.729 3.042,1.927 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 1 engine room relay block.


e.

Measure the resistance according to the value(s) in the table below.

A452342C01
4.76,1.354 5.156,1.594 0.396,0.24 4.146,2.51 4.542,2.24 true 0.313,0.073 0.771,0.448 0.458,0.375 10 false *1 2.073,0.667 2.448,1.01 0.375,0.344 10 false *a 4.198,1.354 4.729,1.76 0.531,0.406 10 false *b 4.854,1.385 5.385,1.781 0.531,0.396 10 false z22 3.792,2.479 4.219,2.74 0.427,0.26 10 false IGCT
*1 No. 1 Engine Room Relay Block - -
*a IGCT NO. 2 Fuse Holder *b Rear view of wire harness connector
(to Battery ECU Assembly)


Standard Resistance:
Tester Connection Condition Specified Condition
z22-16 (IGCT) or 2 (IGCT NO. 2 fuse holder) - Body ground and other terminals Always Below 1 Ω



f.

Install the IGCT NO. 2 fuse to the No. 1 engine room relay block.


g.

Reconnect the battery ECU assembly connector.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT NO. 2)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 2)