Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A9300  Inverter "A" Cooling System Performance  


DTC SUMMARY

MALFUNCTION DESCRIPTION


This DTC indicates when the temperature sensor value inside the inverter has become abnormal. The cause of this malfunction may be one of the following:

Internal inverter malfunction
·

Inverter internal circuit malfunction

·

Malfunction in ECU that controls the inverter

·

Malfunction in sensor for inverter control (coolant temperature sensor)


Hybrid cooling system malfunction
·

Coolant is leaking, insufficient coolant level, frozen or the passenger of coolant is clogged.

·

Grille is blocked.



DESCRIPTION

Refer to the system description for the Cooling System.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>Cooling System

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9300 Inverter "A" Cooling System Performance
·

Inverter coolant temperature increases as well as the temperature of any inverter with converter assembly related parts due to an inverter cooling system malfunction.

·

When the actual temperature of the inverter coolant is higher than the sensor value by a certain value or more and the actual temperature is high.


(1 trip detection logic)
·

Inverter cooling system

·

Inverter water pump assembly

·

Inverter with converter assembly

·

Cooling fan system

·

Wire harness or connector


Comes on Master Warning: Comes on

Related Data List
DTC No. Data List
P0A9300
·

Inverter Coolant Water Temperature

·

Motor Inverter Temperature

·

Generator Inverter Calculated Temperature

·

Boosting Converter Temperature (Upper)

·

Boosting Converter Temperature (Lower)

·

Inverter Water Pump Revolution



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Turn the power switch on (READY) and wait for 5 seconds or more.

8.

Perform a road test according to the freeze frame data item "Vehicle Speed" for approximately 10 minutes.

NOTICE:

As the state of charge of the HV battery voltage may be low after driving in fail-safe mode, it will automatically be charged for 5 to 10 minutes after repairs have been performed and turn the power switch on (READY).


9.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C04
1.563,0.708 1.813,0.417 true 1.844,0.302 2.156,0.5 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control, Motor Generator, Engine / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P0A9300 only is output, or DTCs except the ones in the table below are also output A
DTCs of hybrid control system in the table below are output B
DTCs of motor generator control system in the table below are output C
DTCs of SFI system in the table below are output D


Table 1
Malfunction Content System Relevant DTC
Insulation malfunction Hybrid control system P1C7C49 Hybrid/EV Battery Voltage System (A/C Area) Insulation Resistance Decreased
P1C7D49 Hybrid/EV Battery Voltage System (Hybrid/EV Battery Area) Insulation Resistance Decreased
P1C7E49 Hybrid/EV Battery Voltage System (Transaxle Area) Insulation Resistance Decreased
P1C7F49 Hybrid/EV Battery Voltage System (Direct Current Area) Insulation Resistance Decreased

Table 2
Malfunction Content System Relevant DTC
Sensor and actuator circuit malfunction Hybrid control system P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal
Motor generator control system P0A0011 Motor Electronics Coolant Temperature Sensor Circuit Short to Ground
P0A0015 Motor Electronics Coolant Temperature Sensor Circuit Short to Battery or Open
System malfunction SFI system P059F73 Active Grille Air Shutter "A" Actuator Stuck Closed
P05A072 Active Grille Air Shutter "A" Actuator Stuck Open
P05A074 Active Grille Air Shutter "A" Actuator Slipping
P05A211 Active Grille Air Shutter "A" Circuit Short to Ground
P05A212 Active Grille Air Shutter "A" Circuit Short to Battery
P05A213 Active Grille Air Shutter "A" Circuit Open
P05A27E Active Grille Air Shutter "A" Actuator Stuck On
P05A27F Active Grille Air Shutter "A" Actuator Stuck Off
P05B112 Active Grille Air Shutter "B" Circuit Short to Battery
P05B114 Active Grille Air Shutter "B" Circuit Short to Ground or Open
P05B131 Active Grille Air Shutter "B" No Signal
U028487 Lost Communication with Active Grille Air Shutter Module "A" Missing Message

HINT:
·

P0A9300 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

C

D

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

3.CHECK COOLING SYSTEM

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COOLING SYSTEM

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>Cooling System

HINT:

If the "Cooling System" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT