Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P274A1C  Transmission Fluid Temperature Sensor "C" Voltage Out of Range  P274A1F  Transmission Fluid Temperature Sensor "C" Circuit Intermittent  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the transmission fluid temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Transmission fluid temperature sensor malfunction
·

Internal transmission fluid temperature sensor malfunction

·

Open or short in transmission fluid temperature sensor


Wire harness between the transmission fluid temperature sensor and hybrid vehicle control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness



DESCRIPTION

Refer to the description for DTC P274A11.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>P274A11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P274A1C Transmission Fluid Temperature Sensor "C" Voltage Out of Range After a long soak, the value of the transmission fluid temperature sensor is different from the value of the other temperature sensors.
(2 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle transaxle assembly (Transmission fluid temperature sensor)


Comes on Master Warning: Comes on
P274A1F Transmission Fluid Temperature Sensor "C" Circuit Intermittent Sudden change in transmission fluid temperature sensor output or hunting:
Unusual sudden change in transmission fluid temperature sensor output occurs and offset condition continues for a certain period of time, or unusual change in transmission fluid temperature sensor output occurs repeatedly.
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle transaxle assembly (Transmission fluid temperature sensor)


Comes on Master Warning: Comes on

Related Data List
DTC No. Data List
P274A1C
·

Generator Temperature

·

Motor Temperature

·

Transaxle Oil Temperature


P274A1F Transaxle Oil Temperature

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY


DTC P274A1C
1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off.

5.

Leave the vehicle as is for 5 hours or more and then check the values of the Data List items "Generator Temperature", "Motor Temperature" and "Transaxle Oil Temperature".

6.

Turn the power switch on (IG) and turn the GTS on.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




DTC P274A1F
1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

PROCEDURE

1.CHECK DTC OUTPUT (ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
No DTCs are output, or DTCs except the ones in the table below are also output A
Any of the following DTCs are also output B


Relevant DTC
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid


e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs are output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Relevant DTC
P274A11 Transmission Fluid Temperature Sensor "C" Circuit Short to Ground
P274A15 Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open


e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION FLUID TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION FLUID TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A496617C04
1.469,0.073 1.896,0.333 0.427,0.26 1.583,1.833 1.333,1.583 true 0.917,1.833 1.167,1.615 true 1.563,0.125 2.042,0.448 0.479,0.323 10 false A97 1.594,1.833 2,2.094 0.406,0.26 10 false TTA 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.594,1.844 1.073,2.042 0.479,0.198 10 false ETTA
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A97-40 (TTA) - A97-39 (ETTA) Power switch off 1.393 to 75.8 kΩ



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

NG

9.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)
5.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>P274A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK)
a.

Disconnect the CA2 No. 1 engine room relay block connectors.


b.

Disconnect the A97 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
CA2-10 (TTA) - A97-40 (TTA) Power switch off Below 1 Ω
CA2-11 (ETTA) - A97-39 (ETTA) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
CA2-10 (TTA) or A97-40 (TTA) - Body ground and other terminals Power switch off 10 kΩ or higher
CA2-11 (ETTA) or A97-39 (ETTA) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A97 hybrid vehicle control ECU connector.


e.

Reconnect the CA2 No. 1 engine room relay block connectors.


Result:
Proceed to
OK
NG



OK

7.CHECK CONNECTOR CONNECTION CONDITION (TRANSMISSION FLUID TEMPERATURE SENSOR CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CONNECTOR CONNECTION CONDITION (TRANSMISSION FLUID TEMPERATURE SENSOR CONNECTOR)

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>P274A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - TRANSMISSION FLUID TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - TRANSMISSION FLUID TEMPERATURE SENSOR)
a.

Disconnect the C101 transmission fluid temperature sensor connector.


b.

Disconnect the CA2 No. 1 engine room relay block connectors.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
CA2-10 (TTA) - C101-3 (TTA) Power switch off Below 1 Ω
CA2-11 (ETTA) - C101-13 (ETTA) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
CA2-10 (TTA) or C101-3 (TTA) - Body ground and other terminals Power switch off 10 kΩ or higher
CA2-11 (ETTA) or C101-13 (ETTA) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the CA2 No. 1 engine room relay block connectors.


e.

Reconnect the C101 transmission fluid temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)
a.

Disconnect the CA2 No. 1 engine room relay block connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
CA2-10 (TTA) - CA2-11 (ETTA) Power switch off 1.393 to 75.8 kΩ



c.

Reconnect the CA2 No. 1 engine room relay block connectors.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK)

NG

10.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)
10.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (TRANSMISSION FLUID TEMPERATURE SENSOR)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - TRANSMISSION FLUID TEMPERATURE SENSOR)

NG