Home › Drivetrain › P711 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2019.09–2020.08
RM32K0E _52 Drivetrain _084042 P711 HYBRID TRANSMISSION / TRANSAXLE _0404750 HYBRID VEHICLE TRANSAXLE A

P711 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: If the vehicle height has changed due to suspension or tire replacement

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision System
Initialize back door lock Power Door Lock Control System (Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Suspension, tires, etc.*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



PROCEDURE

Hide 1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 89481B 4.REMOVE DIFFERENTIAL PRESSURE SENSOR

a.
C391944

Disconnect the differential pressure sensor connector.


b.

Remove the nut and differential pressure sensor from the sensor bracket.


Hide 5.REMOVE SENSOR BRACKET

a.
C398735

Remove the bolt and sensor bracket from the cylinder head sub-assembly.


Hide 82121 7.DISCONNECT ENGINE WIRE

a.
C406251

Disengage the 5 clamps.


b.
C406279C01
2.833,1.74 3.042,1.938 0.208,0.198 10 true *1 0.99,1.719 1.208,1.875 0.219,0.156 10 true *2 2.458,0.177 2.646,0.375 0.188,0.198 10 true *3
*1 Resolver (Transmission Fluid Temperature Sensor) Connector
*2 Shift Lever Position Sensor Connector
*3 Generator Temperature Sensor Connector


Disengage the clamp.


c.

Remove the bolt.


d.

Disconnect the resolver (transmission fluid temperature sensor) connector.


e.

Disconnect the shift lever position sensor connector.

NOTICE:
C441192

After disconnecting the engine wire, cover the connector of the shift lever position sensor with tape (non-residue type) or equivalent to prevent the entry of foreign matter or water.



f.

Disconnect the generator temperature sensor connector.


Hide 821H2 8.REMOVE HV AIR CONDITIONING WIRE

a.
C406252

Remove the bolt.


b.

Disengage the guide to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.


c.
C406253

Disengage the clamp.


d.
A407267C03
1.073,0.594 0.531,0.26 true 0.354,0.156 0.667,0.313 0.313,0.156 10 false *a
*a Green-colored Lock
V100137

Slide


Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



Hide 28193 9.REMOVE STARTER HOLE INSULATOR

a.
C379388

Remove the 2 bolts and starter hole insulator from the engine assembly.


Hide 11363A 10.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C406255

Remove the flywheel housing side cover from the engine assembly.


Hide 12.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.
C411131

Remove the 3 bolts and drive shaft heat insulator sub-assembly from the cylinder block sub-assembly.


Hide 13.REMOVE ENGINE ASSEMBLY

a.
C379393

Remove the 8 bolts and engine assembly from the hybrid vehicle transaxle assembly.

NOTICE:
·

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.

·

To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during engine assembly removal and installation.




Hide 51201 14.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C406256

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 15.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C406257

Remove the 5 bolts and No. 2 engine moving control rod from the hybrid vehicle transaxle assembly.


Hide G125A 17.REMOVE MOTOR COOLING COOLER

a.
C406258

Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.


b.
C406259

Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


c.

Remove the bolt and No. 1 oil cooler tube clamp from the hose bracket.


d.
C406260

Remove the 3 bolts and motor cooling cooler with No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.



Hide G1251B 18.REMOVE NO. 1 MOTOR COOLING PIPE

a.
C406261

Loosen the flare nut of the No. 1 motor cooling pipe and disconnect the No. 1 motor cooling pipe from the union.


b.
C406262

Remove the bolt, No. 1 oil cooler tube clamp and No. 1 motor cooling pipe from the No. 1 transmission control cable bracket.


Hide 16575C 19.REMOVE NO. 1 WATER HOSE CLAMP BRACKET

a.
C406263

Remove the bolt and No. 1 water hose clamp bracket from the hybrid vehicle transaxle assembly.


Hide 44781E 20.REMOVE HOSE BRACKET

a.
C406264

Remove the 2 bolts and hose bracket from the hybrid vehicle transaxle assembly.


Hide 33823 21.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C406265

Remove the 2 bolts and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.


Hide 22.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C406266

Remove the 2 bolts and 2 wire harness clamp brackets from the hybrid vehicle transaxle assembly.


Hide 23.REMOVE TRANSAXLE HOUSING PLUG

a.
C379406

Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.


Hide 24.REMOVE STUD BOLT

a.
C411136

Using a E8 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.


Hide 25.REMOVE UNION

HINT:

Perform this procedure only when replacement of the union or O-ring is necessary.


a.
C411137

Remove the union and O-ring from the hybrid vehicle transaxle assembly.