Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM J

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch EV Mode Circuit  


DESCRIPTION

The EV drive mode signal will be sent to the hybrid vehicle control ECU when the EV drive mode switch (electric parking brake switch assembly) is operated. If the specified conditions are met, the system enters EV drive mode and the vehicle will be driven using EV drive mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the EV drive mode indicator.

WIRING DIAGRAM

A376617E49
1.49,1.25 3.438,1.563 1.948,0.313 10 false Combination Meter Assembly 2.104,1.896 2.854,2.156 0.75,0.26 10 false EV MODE 1.281,2.854 3.708,3.292 2.427,0.438 10 false EV Drive Mode Switch (Electric Parking Brake Switch Assembly) 4.708,2.99 6.49,3.479 1.781,0.49 10 false Hybrid Vehicle Control ECU 5.104,2.063 5.688,2.323 0.583,0.26 10 false EVSW 4.802,2.063 5.083,2.344 0.281,0.281 10 false 33 4.719,2.813 5.115,3.021 0.396,0.208 10 false F161 1.292,2.667 1.573,2.948 0.281,0.281 10 false F67 5.76,1.635 6.042,1.917 0.281,0.281 10 false +B 1.563,2.063 1.844,2.344 0.281,0.281 10 false 8 1.76,2.073 2.25,2.271 0.49,0.198 10 false E 3,2.073 3.281,2.354 0.281,0.281 10 false S 3.198,1.896 3.531,2.125 0.333,0.229 10 false 11*1 0.583,3.385 2.531,3.698 1.948,0.313 10 false : CAN Communication Line 3.198,2.073 3.563,2.344 0.365,0.271 10 false 13*2 0.167,2.792 0.958,2.979 0.792,0.188 10 false *1: for LHD 0.177,3.052 0.969,3.24 0.792,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

Depending on the condition of the hybrid control system and the driving conditions, the drive mode may not be able to be changed to EV drive mode and a warning message will be displayed on the multi-information display.

HINT:

Under the following conditions, the drive mode will not be able to be changed to EV drive mode:

·

The hybrid control system is extremely hot.

·

The hybrid control system is extremely cold.

·

The engine is warming up.

·

The SOC (State of Charge) of the HV battery is low.

·

The vehicle is being driven at a speed higher than the specified value.

·

The accelerator pedal is being fully depressed or the vehicle is climbing a slope.

·

The defroster is on.

·

DTCs are stored.



PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
a.

Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV drive mode.

Result:
Result Proceed to
No buzzer sounded and no message was displayed on multi-information display A
A buzzer sounded and a message was displayed on multi-information display B


HINT:

If a buzzer sounds and a message is displayed on the multi-information display, one or more of the EV drive mode entry conditions have not been met.




A

2.READ VALUE USING GTS (CAN BUS CHECK)

B

END

2.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / CAN Bus Check.

CAN Bus Check
50007
Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



e.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



f.

Turn the power switch off.



A

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)

B

GO TO DTC CHART

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / EV Mode, EV Mode Switch.

Powertrain > Hybrid Control > Data List
Tester Display
EV Mode
EV Mode Switch
50003 397 79,80

e.

Read the values displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
EV Mode EV drive mode transition availability ON or OFF In EV drive mode: ON
EV Mode Switch EV drive mode switch condition ON or OFF EV drive mode switch being pushed and held: ON
EV drive mode switch not operated: OFF
Result:
Result Proceed to
The display changes according to the EV drive mode switch operation A
The display does not change according to the EV drive mode switch operation B



f.

Turn the power switch off.



A

B

5.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
5.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the EV drive mode switch (electric parking brake switch assembly) connector.


b.
A373476C05
0.427,0.885 0.844,1.135 0.417,0.25 0.844,1.688 1.24,1.271 true 0.115,0.156 0.427,0.313 0.313,0.156 10 false *a 0.521,0.958 0.802,1.167 0.281,0.208 10 false F67 0.74,1.677 1.146,1.865 0.406,0.188 10 false E
*a Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F67-8 (E) - Body ground Always Below 1 Ω



c.

Reconnect the EV drive mode switch (electric parking brake switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the EV drive mode switch (electric parking brake switch assembly) connector.


c.
A452678C01
1.49,0.229 1.938,0.458 0.448,0.229 0.073,3.26 0.417,3.5 0.344,0.24 1.74,3.292 2.083,3.531 0.344,0.24 1.854,2.083 1.646,1.563 true 0.698,4.115 0.958,3.583 true 2.979,4.115 2.844,3.594 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.135,2.323 0.448,2.521 0.313,0.198 10 false *b 1.563,0.271 2.177,0.469 0.615,0.198 10 false F161 1.729,2.135 2.219,2.313 0.49,0.177 10 false EVSW 0.115,3.302 0.417,3.479 0.302,0.177 10 false F67 1.802,3.344 2.104,3.521 0.302,0.177 10 false F67 0.323,2.688 0.635,2.885 0.313,0.198 10 false *A 2.021,2.719 2.333,2.917 0.313,0.198 10 false *B 0.625,4.156 0.823,4.344 0.198,0.188 10 false S 2.99,4.167 3.135,4.354 0.146,0.188 10 false S
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F161-33 (EVSW) - F67-11 (S) Always Below 1 Ω
F161-33 (EVSW) or F67-11 (S) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F161-33 (EVSW) - F67-13 (S) Always Below 1 Ω
F161-33 (EVSW) or F67-13 (S) - Body ground Always 10 kΩ or higher



d.

Reconnect the EV drive mode switch (electric parking brake switch assembly) connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR