Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P070562  Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure  


DESCRIPTION

The shift lever position sensor sends 7 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses these signals to detect the shift lever position (P, R, N or D). The hybrid vehicle control ECU also uses this information to determine the intended direction of travel (forward or reverse).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P070562 Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure Shift sensor circuit malfunction (abnormal pattern)
A malfunction in the P, R, N or D circuit is detected based on the shift sensor input pattern.
(1 trip detection logic)
·

Wire harness or connector

·

Shift lever position sensor

·

Hybrid vehicle control ECU


Does not come on Master Warning: Comes on

Related Data List
DTC No. Data List
P070562
·

Shift Position

·

Shift Position Sensor (PNB)

·

Shift Position Sensor (PR)

·

Shift Position Sensor (DB1)

·

Shift Position Sensor (DB2)

·

Shift Position Sensor (N)

·

Shift Position Sensor (R)

·

Shift Position Sensor (P)



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Slowly move the shift lever from P to S then back to P.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A407614E16
0.542,4 1.344,4.302 0.802,0.302 10 false C96 0.531,4.167 3,4.479 2.469,0.313 10 false Shift Lever Position Sensor 1.906,0.563 2.219,0.76 0.313,0.198 10 false +B 1.99,1.073 2.302,1.271 0.313,0.198 10 false P 1.979,1.417 2.292,1.615 0.313,0.198 10 false R 1.99,1.802 2.302,2 0.313,0.198 10 false N 1.823,2.125 2.135,2.323 0.313,0.198 10 false DB1 1.896,2.802 2.208,3 0.313,0.198 10 false PR 1.813,3.177 2.125,3.375 0.313,0.198 10 false PNB 1.823,2.469 2.135,2.667 0.313,0.198 10 false DB2 2.198,0.563 2.51,0.76 0.313,0.198 10 false 7 2.198,1.073 2.51,1.271 0.313,0.198 10 false 8 2.208,1.417 2.521,1.615 0.313,0.198 10 false 9 2.198,1.802 2.51,2 0.313,0.198 10 false 2 2.198,2.125 2.51,2.323 0.313,0.198 10 false 1 2.198,2.469 2.51,2.667 0.313,0.198 10 false 6 2.198,2.802 2.51,3 0.313,0.198 10 false 3 2.188,3.177 2.5,3.375 0.313,0.198 10 false 4 4.563,0.563 4.875,0.76 0.313,0.198 10 false 18 4.563,1.073 4.875,1.271 0.313,0.198 10 false 28 4.625,1.417 4.938,1.615 0.313,0.198 10 false 2 4.563,1.802 4.875,2 0.313,0.198 10 false 29 4.615,2.125 4.927,2.323 0.313,0.198 10 false 3 4.552,2.469 4.865,2.667 0.313,0.198 10 false 15 4.552,2.792 4.865,2.99 0.313,0.198 10 false 16 4.563,3.156 4.875,3.354 0.313,0.198 10 false 30 4.823,0.646 5.427,0.875 0.604,0.229 10 false PSFT 4.823,1.073 5.427,1.302 0.604,0.229 10 false P 4.823,1.417 5.135,1.615 0.313,0.198 10 false R 4.823,1.802 5.135,2 0.313,0.198 10 false N 4.813,2.125 5.125,2.323 0.313,0.198 10 false DB1 4.813,2.458 5.125,2.656 0.313,0.198 10 false DB2 4.813,2.802 5.125,3 0.313,0.198 10 false PR 4.802,3.156 5.115,3.354 0.313,0.198 10 false PNB 4.781,4.01 5.094,4.208 0.313,0.198 10 false A97 4.781,4.188 6.625,4.573 1.844,0.385 10 false Hybrid Vehicle Control ECU

PROCEDURE

1.READ VALUE USING GTS (SHIFT POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Position Sensor (PNB), Shift Position Sensor (PR), Shift Position Sensor (DB1), Shift Position Sensor (DB2), Shift Position Sensor (N), Shift Position Sensor (R), Shift Position Sensor (P).

Powertrain > Hybrid Control > Data List
Tester Display
Shift Position Sensor (PNB)
Shift Position Sensor (PR)
Shift Position Sensor (DB1)
Shift Position Sensor (DB2)
Shift Position Sensor (N)
Shift Position Sensor (R)
Shift Position Sensor (P)
50003 397 400,401,403,402,404,405,406

d.

While slowly moving the shift lever from P to S, then back to P, read the Data List (Shift Position Sensor) displayed on the GTS.

HINT:

Be sure to move the shift lever slowly.


Standard:
Data List Shift Position
P R N D or S
Shift Position Sensor (P) ON OFF OFF OFF
Shift Position Sensor (R) OFF ON OFF OFF
Shift Position Sensor (PR) ON ON OFF OFF
Shift Position Sensor (N) OFF OFF ON OFF
Shift Position Sensor (DB1) OFF OFF OFF ON
Shift Position Sensor (DB2) OFF OFF OFF ON
Shift Position Sensor (PNB) ON OFF ON OFF



e.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
OK:

DTC P070562 is not output.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK FOR INTERMITTENT PROBLEMS

NG

3.INSPECT SHIFT LEVER POSITION SENSOR
2.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.INSPECT SHIFT LEVER POSITION SENSOR
a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

A409147C82
1.552,0.333 1.969,0.583 0.417,0.25 2.365,1.271 3.75,0.583 true 2.25,1.26 3.167,0.583 true 1.865,1.354 2.417,0.583 true 1.167,0.583 1.74,1.354 true 0.667,2.333 1.594,1.469 true 1.167,2.333 1.719,1.469 true 2.417,2.333 1.844,1.469 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 3.771,0.427 4.083,0.667 0.313,0.24 10 false R 2.354,0.417 2.771,0.656 0.417,0.24 10 false DB2 1.656,0.385 2.073,0.625 0.417,0.24 10 false A97 2.406,2.365 2.823,2.604 0.417,0.24 10 false P 3.094,0.417 3.51,0.656 0.417,0.24 10 false DB1 1.052,0.427 1.469,0.667 0.417,0.24 10 false PR 0.49,2.365 0.906,2.604 0.417,0.24 10 false PNB 1.115,2.365 1.531,2.604 0.417,0.24 10 false N
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A97-28 (P) - Body ground Power switch on (IG)
Shift lever in P
6 to 14 V
Power switch on (IG)
Shift lever in any position except P
0 to 1.5 V
A97-2 (R) - Body ground Power switch on (IG)
Shift lever in R
6 to 14 V
Power switch on (IG)
Shift lever in any position except R
0 to 1.5 V
A97-16 (PR) - Body ground Power switch on (IG)
Shift lever in P or R
6 to 14 V
Power switch on (IG)
Shift lever in any position except P or R
0 to 1.5 V
A97-29 (N) - Body ground Power switch on (IG)
Shift lever in N
6 to 14 V
Power switch on (IG)
Shift lever in any position except N
0 to 1.5 V
A97-3 (DB1) - Body ground Power switch on (IG)
Shift lever in D or S
6 to 14 V
Power switch on (IG)
Shift lever in any position except D or S
0 to 1.5 V
A97-15 (DB2) - Body ground Power switch on (IG)
Shift lever in D or S
6 to 14 V
Power switch on (IG)
Shift lever in any position except D or S
0 to 1.5 V
A97-30 (PNB) - Body ground Power switch on (IG)
Shift lever in P or N
6 to 14 V
Power switch on (IG)
Shift lever in any position except P or N
0 to 1.5 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A452310N01
0.563,1.156 0.927,1.365 0.365,0.208 0.583,1.188 0.885,1.333 0.302,0.146 10 true C96

Disconnect the shift lever position sensor connector.

Click hereDrivetrain>P711 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER POSITION SENSOR>REMOVAL


b.

Turn the power switch on (IG).


c.
A373228C22
1.49,0.198 1.927,0.469 0.438,0.271 1.948,1.74 1.698,1.313 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.573,0.25 2,0.49 0.427,0.24 10 false C96 1.927,1.781 2.24,1.979 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Shift Lever Position Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C96-7 (+B) - Body ground Power switch on (IG) 7.5 to 14 V


NOTICE:

Turning the power switch on (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT SHIFT LEVER POSITION SENSOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
5.INSPECT SHIFT LEVER POSITION SENSOR
a.
A452310N01
0.563,1.156 0.927,1.365 0.365,0.208 0.583,1.188 0.885,1.333 0.302,0.146 10 true C96

Disconnect the shift lever position sensor connector.


b.
A417629C06
0.198,0.583 0.615,0.833 0.417,0.25 1.823,0.875 2.5,0.333 true 1.563,0.875 2,0.333 true 1.344,0.906 1.5,0.333 true 1.146,0.917 0.917,0.5 true 0.833,1.917 1.24,1.302 true 1.417,1.917 1.438,1.292 true 2.021,1.917 1.729,1.281 true 2.583,1.917 2,1.302 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.427,0.167 1.885,0.365 0.458,0.198 10 false PR 0.75,0.323 1.208,0.521 0.458,0.198 10 false PNB 1.99,0.156 2.448,0.354 0.458,0.198 10 false N 2.448,0.167 2.906,0.365 0.458,0.198 10 false DB1 2.542,1.927 3,2.125 0.458,0.198 10 false DB2 1.948,1.927 2.406,2.125 0.458,0.198 10 false +B 1.365,1.948 1.823,2.146 0.458,0.198 10 false P 0.76,1.938 1.219,2.135 0.458,0.198 10 false R 0.292,0.625 0.75,0.823 0.458,0.198 10 false C96
*a Component without harness connected
(Shift Lever Position Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C96-7 (+B) - C96-3 (PR) Shift lever in P Below 1 Ω
C96-7 (+B) - C96-4 (PNB) Below 1 Ω
C96-7 (+B) - C96-8 (P) Below 1 Ω
C96-7 (+B) - C96-1 (DB1), C96-2 (N), C96-6 (DB2) and C96-9 (R) 10 kΩ or higher
C96-7 (+B) - C96-3 (PR) Shift lever in R Below 1 Ω
C96-7 (+B) - C96-9 (R) Below 1 Ω
C96-7 (+B) - C96-1 (DB1), C96-2 (N), C96-4 (PNB), C96-6 (DB2) and C96-8 (P) 10 kΩ or higher
C96-7 (+B) - C96-2 (N) Shift lever in N Below 1 Ω
C96-7 (+B) - C96-4 (PNB) Below 1 Ω
C96-7 (+B) - C96-1 (DB1), C96-3 (PR), C96-6 (DB2), C96-8 (P) and C96-9 (R) 10 kΩ or higher
C96-7 (+B) - C96-1 (DB1) Shift lever in D or S Below 1 Ω
C96-7 (+B) - C96-6 (DB2) Below 1 Ω
C96-7 (+B) - C96-2 (N), C96-3 (PR), C96-4 (PNB), C96-8 (P) and C96-9 (R) 10 kΩ or higher


HINT:

Terminal No. 5 on the component side connector is empty.



c.

Reconnect the shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the shift lever position sensor connector.


b.

Disconnect the hybrid vehicle control ECU connector.


c.
A434288C05
1.49,0.333 1.906,0.583 0.417,0.25 1.458,2.448 1.875,2.698 0.417,0.25 1.729,1.365 2.188,1.854 true 2.073,3.771 2.333,4.417 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 0.188,2.333 0.5,2.49 0.313,0.156 10 false *b 2.198,1.896 2.51,2.094 0.313,0.198 10 false +B 2.208,4.458 2.635,4.656 0.427,0.198 10 false PSFT 1.583,0.385 2.052,0.625 0.469,0.24 10 false C96 1.563,2.5 1.885,2.667 0.323,0.167 10 false A97
*a Front view of wire harness connector
(to Shift Lever Position Sensor)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C96-7 (+B) - A97-18 (PSFT) Power switch off Below 1 Ω
C96-7 (+B) or A97-18 (PSFT) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the hybrid vehicle control ECU connector.


e.

Reconnect the shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR