Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM J

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

When the shift lever is in S, different ranges can be chosen using the floor shift sequential gate.

WIRING DIAGRAM

A452374E01
1.875,3.427 2.333,3.625 0.458,0.198 10 false F17 1.875,3.604 4.021,4.208 2.146,0.604 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 1.99,2.01 2.448,2.208 0.458,0.198 10 false 2 2.24,2.01 2.698,2.208 0.458,0.198 10 false E 2.24,1.333 2.698,1.531 0.458,0.198 10 false IG 2.01,1.344 2.469,1.542 0.458,0.198 10 false 4 0.26,1.427 1.198,2.031 0.938,0.604 10 false from ECU-ACC Fuse 3.51,1.344 3.969,1.542 0.458,0.198 10 false S 3.771,1.344 4.229,1.542 0.458,0.198 10 false 5 3.781,1.792 4.24,1.99 0.458,0.198 10 false 3*1 3.292,2 3.75,2.198 0.458,0.198 10 false SFTU 3.292,2.677 3.75,2.875 0.458,0.198 10 false SFTD 3.771,2.458 4.229,2.656 0.458,0.198 10 false 1*1 5.25,2.698 5.708,2.896 0.458,0.198 10 false 11 5.24,2.031 5.698,2.229 0.458,0.198 10 false 24 5.25,1.333 5.708,1.531 0.458,0.198 10 false 25 5.521,1.438 5.979,1.635 0.458,0.198 10 false M 5.51,2.115 5.969,2.313 0.458,0.198 10 false SFTU 5.51,2.781 6.031,3.021 0.521,0.24 10 false SFTD 5,3.813 5.458,4.01 0.458,0.198 10 false F161 5,3.979 6.719,4.542 1.719,0.563 10 false Hybrid Vehicle Control ECU 0.323,4.177 2.01,4.375 1.688,0.198 10 false *1: for LHD 0.323,4.469 2.01,4.667 1.688,0.198 10 false *2: for RHD 3.781,2.677 4.698,2.875 0.917,0.198 10 false 3*2 3.781,2 4.698,2.198 0.917,0.198 10 false 1*2

PROCEDURE

1.READ VALUE USING GTS (SPORTS SHIFT POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift Position.

Powertrain > Hybrid Control > Data List
Tester Display
Sports Shift Position
50003 397 233

d.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Sports Shift Position Sports shift position 0 to 255 Shift lever in S, "+" or "-": 1 to 6
Shift lever in any position other than S, "+" and "-": 255
Result:
Result Proceed to
The GTS display changes according to the shift lever operation A
The GTS display does not change according to the shift lever operation B



e.

Turn the power switch off.



A

2.READ VALUE USING GTS (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL)

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.READ VALUE USING GTS (SPORTS SHIFT UP SIGNAL, SPORTS SHIFT DOWN SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift UP Signal, Sports Shift DOWN Signal.

Powertrain > Hybrid Control > Data List
Tester Display
Sports Shift UP Signal
Sports Shift DOWN Signal
50003 397 83,82

d.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Sports Shift UP Signal Operation of "+" transmission control switch. ON or OFF Shift lever held in "+" operated: ON
Shift lever in S: OFF
Sports Shift DOWN Signal Operation of "-" transmission control switch. ON or OFF Shift lever held in "-" operated: ON
Shift lever in S: OFF
Result:
Result Proceed to
The GTS display changes according to the transmission control switch (shift lock control unit assembly) operation A
The GTS display does not change according to the transmission control switch (shift lock control unit assembly) operation B



e.

Turn the power switch off.



A

3.CHECK FOR INTERMITTENT PROBLEMS

B

7.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
3.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the transmission control switch (shift lock control unit assembly) connector.


b.
C251979C91
0.521,1.073 0.865,1.281 0.344,0.208 1.188,1.708 1.604,1.292 true 2.24,1.708 1.854,1.292 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.594,1.104 0.906,1.26 0.313,0.156 10 false F17 1.083,1.677 1.396,1.833 0.313,0.156 10 false E 2.292,1.646 2.604,1.802 0.313,0.156 10 false IG
*a Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F17-4 (IG) - Body ground Power switch on (IG) 11 to 14 V
F17-4 (IG) - Body ground Power switch off Below 1 V



c.

Turn the power switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F17-2 (E) - Body ground Power switch off Below 1 Ω



e.

Reconnect the transmission control switch (shift lock control unit assembly) connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

NG

CHECK POWER SOURCE CIRCUIT

5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY))

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY))
a.
A365589C17
1.542,0.156 1.938,0.406 0.396,0.25 2.667,1.823 2.375,1.302 true 2.771,0.344 2.469,1.083 true 3.083,1.5 2.521,1.292 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *a 2.823,0.198 3.292,0.396 0.469,0.198 10 false SFTD 2.563,1.844 3.031,2.042 0.469,0.198 10 false SFTU 1.583,0.198 1.969,0.396 0.385,0.198 10 false F161 3.094,1.5 3.385,1.719 0.292,0.219 10 false M
*a Front view of wire harness connector
(to hybrid vehicle control ECU)


Disconnect the hybrid vehicle control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

Standard Voltage:
Tester Connection Condition Specified Condition
F161-25 (M) - Body ground Power switch on (IG)
Shift lever in S, "+" or "-"
11 to 14 V
Power switch on (IG)
Except shift lever in S, "+" and "-"
Below 1 V


NOTICE:

If the power switch is turned on (IG) with the hybrid vehicle control ECU connector disconnected, other DTCs will be stored. After performing the inspection, clear the DTCs.



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
F161-24 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
F161-24 (SFTU) - Body ground Shift lever not operated 10 kΩ or higher
F161-11 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
F161-11 (SFTD) - Body ground Shift lever not operated 10 kΩ or higher



f.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the transmission control switch (shift lock control unit assembly) connector.


b.
C239095C88
1.458,0.26 1.896,0.479 0.438,0.219 1.833,1.75 1.719,1.344 true 2.417,1.75 2.01,1.333 true 2.823,1.573 2.323,1.323 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.573,0.292 1.885,0.448 0.313,0.156 10 false F17 1.75,1.771 2.271,1.948 0.521,0.177 10 false SFTU*A 2.385,1.781 2.823,1.969 0.438,0.188 10 false E 2.667,1.583 3.25,1.75 0.583,0.167 10 false SFTD*A 1.76,1.979 2.677,2.177 0.917,0.198 10 false SFTD*B 2.667,1.813 3.24,2.031 0.573,0.219 10 false SFTU*B
*A for LHD
*B for RHD
*a Component without harness connected
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F17-3 (SFTU) - F17-2 (E) Shift lever held in "+" Below 1 Ω
F17-3 (SFTU) - F17-2 (E) Shift lever not operated 10 kΩ or higher
F17-1 (SFTD) - F17-2 (E) Shift lever held in "-" Below 1 Ω
F17-1 (SFTD) - F17-2 (E) Shift lever not operated 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F17-1 (SFTU) - F17-2 (E) Shift lever held in "+" Below 1 Ω
F17-1 (SFTU) - F17-2 (E) Shift lever not operated 10 kΩ or higher
F17-3 (SFTD) - F17-2 (E) Shift lever held in "-" Below 1 Ω
F17-3 (SFTD) - F17-2 (E) Shift lever not operated 10 kΩ or higher



c.

Reconnect the transmission control switch (shift lock control unit assembly) connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A365589C20
1.542,0.156 1.938,0.406 0.396,0.25 2.667,1.823 2.375,1.271 true 2.771,0.344 2.448,1.094 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *a 2.823,0.198 3.292,0.396 0.469,0.198 10 false SFTD 2.563,1.844 3.031,2.042 0.469,0.198 10 false SFTU 1.594,0.198 1.979,0.396 0.385,0.198 10 false F161
*a Front view of wire harness connector
(to hybrid vehicle control ECU)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Condition Specified Condition
F161-24 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
F161-24 (SFTU) - Body ground Shift lever not operated 10 kΩ or higher
F161-11 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
F161-11 (SFTD) - Body ground Shift lever not operated 10 kΩ or higher



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR