Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HV BATTERY THERMISTOR › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404418 HV BATTERY THERMISTOR A

M20A-FXS HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during hybrid battery thermistor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

Hide G920Q 3.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444040

Remove the 4 nuts.


b.
A444041C01
0.583,2.646 0.531,2.406 0.531,2.406 0.26,2.406 true 1.479,2.896 1.781,2.896 true 0.094,2.313 0.406,2.51 0.313,0.198 10 false *2 1.792,2.802 2.104,3 0.313,0.198 10 false *1
*1 No. 1 Hybrid Battery Shield Sub-assembly
*2 Rear Hybrid Battery Shield Sub-assembly
V113147

Pull Back


Pull back the rear hybrid battery shield sub-assembly and remove the No. 1 hybrid battery shield sub-assembly from the HV battery.

HINT:

Pull back the rear hybrid battery shield sub-assembly until it is separated from the stud bolt of the No. 1 hybrid battery shield sub-assembly.



Hide G92D1 4.REMOVE NO. 1 HYBRID BATTERY INTAKE DUCT

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444042

Disengage the claw of hybrid battery thermistor (sensor portion) and disconnect the hybrid battery thermistor from the No. 1 HV battery cover intake duct.


b.

Disengage the claw to remove the No. 1 HV battery cover intake duct from the HV battery.


Hide G9282 5.REMOVE HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444043

Disengage the clamp.


b.
A444044

Disengage the clamp.


c.

Disconnect the battery voltage sensor connector.


d.
A444045

Disengage the 4 clamps.


e.
A444046

Disengage the 3 claws of the hybrid battery thermistor (sensor portions) and remove the hybrid battery thermistor from the HV battery.