Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HV RELAY ASSEMBLY › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404424 HV RELAY ASSEMBLY A

M20A-FXS HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 73350C 8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 11.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 12.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 13.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 14.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 71033 16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N4A 17.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 18.DISCONNECT HV FLOOR UNDER WIRE

Hide G92PC 20.REMOVE NO. 1 HV BATTERY PROTECTOR

Hide G920L 22.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

Hide G92J5 23.REMOVE NO. 1 HYBRID BATTERY PACKING

Hide 24.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444033

Remove the bolt and disconnect the electric vehicle battery plug assembly.


b.
A444034

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.



c.

Disengage the clamp.


d.
A444035

Disengage the 2 claws and open the wiring harness protector.


e.
A444036

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.



f.
A444037C01
2.177,2.688 2.49,2.688 true 2.51,2.594 2.823,2.792 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the wiring harness protector.


g.
A444038

Disconnect the HV battery junction block assembly connector.


h.
A444039

Remove the 4 nuts and HV battery junction block assembly from the No. 1 hybrid battery shield sub-assembly.

NOTICE:

If the HV battery junction block assembly has been struck or dropped, replace it with a new one.