Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HV BATTERY THERMISTOR › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404418 HV BATTERY THERMISTOR A

M20A-FXS HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR  INSTALLATION  


PROCEDURE

Hide G9282 1.INSTALL HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A444077C01
0.323,0.979 0.406,0.281 0.406,0.281 0.677,0.281 true 1.573,1.177 1.844,0.323 1.844,0.323 2.115,0.323 true 2.646,1.969 2.885,1.969 2.885,1.969 3.052,1.25 true 0.698,0.167 0.927,0.385 0.229,0.219 10 true *a 2.104,0.208 2.333,0.427 0.229,0.219 10 true *b 2.458,1.865 2.656,2.052 0.198,0.188 10 true *c
*a 1st Module from the HV Battery Junction Block Assembly Side
(Wire harness color: Blue)
*b 14th Module from the HV Battery Junction Block Assembly Side
(Wire harness color: White)
*c 30th Module from the HV Battery Junction Block Assembly Side
(Wire harness color: Red)


Engage the 3 claws of the hybrid battery thermistor (sensor portions) to install the hybrid battery thermistor to the HV battery.

HINT:

Install each hybrid battery thermistor (sensor portion) to the appropriate location shown in the illustration.



b.
A444045C01
0.646,1.052 0.781,0.229 0.781,0.229 1,0.229 true 1.177,1.177 1.396,2.052 1.396,2.052 1.583,2.052 true 1.771,1.031 1.896,0.292 1.896,0.292 2.115,0.292 true 2.688,1.146 2.802,2.031 2.802,2.031 2.979,2.031 true 1.031,0.135 1.26,0.323 0.229,0.188 10 true *a 1.594,1.969 1.823,2.156 0.229,0.188 10 true *b 2.125,0.188 2.354,0.375 0.229,0.188 10 true *c 2.979,1.948 3.208,2.135 0.229,0.188 10 true *d
*a 4th Module from the HV Battery Junction Block Assembly Side
*b 10th Module from the HV Battery Junction Block Assembly Side
*c 16th Module from the HV Battery Junction Block Assembly Side
*d 26th Module from the HV Battery Junction Block Assembly Side


Engage the 4 clamps in the locations shown in the illustration.


c.

Connect the battery voltage sensor connector.


d.

Engage the clamp.


e.

Engage the clamp.


Hide G92D1 2.INSTALL NO. 1 HYBRID BATTERY INTAKE DUCT

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Engage the claw to install the No. 1 HV battery cover intake duct to the HV battery.


b.

Engage the claw of hybrid battery thermistor (sensor portion) to connect the hybrid battery thermistor to the No. 1 HV battery cover intake duct.


Hide G920Q 3.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Pull back the rear hybrid battery shield sub-assembly to install the No. 1 hybrid battery shield sub-assembly to the HV battery.

HINT:

Pull back the rear hybrid battery shield sub-assembly until there is sufficient clearance for the stud bolt of the No. 1 hybrid battery shield sub-assembly.



b.

Install the 4 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)