Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › WATER PUMP WITH MOTOR › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404419 WATER PUMP WITH MOTOR A

M20A-FXS HYBRID / BATTERY CONTROL  WATER PUMP WITH MOTOR  INSTALLATION  


PROCEDURE

Hide G9040 1.INSTALL INVERTER WATER PUMP WITH MOTOR ASSEMBLY

a.
A371731C05
2.604,3.906 2.427,3.5 2.427,3.5 2.219,3.5 true 2.146,0.49 2.344,0.49 2.344,0.49 2.552,0.844 true 2.156,1.167 2.333,1.167 2.333,1.167 2.531,0.927 true 2.729,3.896 2.76,3.51 2.76,3.51 2.885,3.51 true 0.5,3.354 0.729,3.531 0.229,0.177 10 true *2 0.5,0.156 0.729,0.333 0.229,0.177 10 true *1 1.479,3.667 2,3.99 0.521,0.323 10 false 180° 0.76,1.125 1.281,1.448 0.521,0.323 10 false 180° 0.948,3.51 1.292,3.792 0.344,0.281 10 false 45° 2.063,3.427 2.25,3.656 0.188,0.229 10 false *b 1.99,0.417 2.177,0.646 0.188,0.229 10 false *a 1.99,1.083 2.302,1.281 0.313,0.198 10 false *c 2.927,3.438 3.24,3.635 0.313,0.198 10 false *c 2.552,4.406 2.865,4.604 0.313,0.198 10 false *d 1.938,0.781 2.25,0.979 0.313,0.198 10 false *d 1.167,3.302 1.479,3.5 0.313,0.198 10 false *e 0.531,4.021 0.844,4.219 0.313,0.198 10 false *f 0.917,0.135 1.229,0.333 0.313,0.198 10 false *f 1.677,0.521 1.99,0.719 0.313,0.198 10 false *g
*1 Inlet Hybrid Water Pump Hose
*2 Outlet No. 1 Hybrid Water Pump Hose
*a Alignment Mark (White)
*b Alignment Mark (White)
*c Rib
*d 2 to 11 mm (0.0787 to 0.236 in.)
*e Up
*f Front of Vehicle
*g RH Side


Connect the outlet No. 1 hybrid water pump hose and inlet hybrid water pump hose to the inverter water pump with motor assembly and slide the 2 clips to secure them.

NOTICE:
·

To prevent foreign matter from entering the inverter water pump with motor assembly and inverter cooling system, do not remove the pieces of cloth from the pipes and disconnected hoses until installation.

·

Make sure to align the alignment marks of the hoses with the ribs of the inverter water pump with motor assembly.

·

Do not apply excessive force to the hoses.

·

If the inverter water pump assembly has been struck or dropped, replace it.



HINT:

Make sure that the clips are positioned as shown in the illustration.



b.

Temporarily install the inverter water pump with motor assembly to the fan shroud assembly with the 2 bolts.


c.

Fully tighten the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

As overtightening the bolts may damage the fan shroud assembly, make sure to use a torque wrench.



d.

Connect the inverter water pump with motor assembly connector.

NOTICE:

If a dustproof cap is installed to the inverter water pump with motor assembly connector, do not remove it until the connector is to be connected.



Hide 51410 4.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY