Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2019.09
RM32K0E _55 Steering _061344 STEERING GEAR / LINKAGE _0299717 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering gear assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for Calibration:(Click here)

PROCEDURE

Hide 1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45100 2.SECURE STEERING WHEEL ASSEMBLY

a.
C365806

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 4.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 5.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C365808N02
0.156,0.135 0.344,0.375 0.188,0.24 10 false A 2.167,2.375 2.354,2.615 0.188,0.24 10 false B

Separate the clip (A), disengage the clip (B) from the vehicle body and separate the No. 1 steering column hole cover sub-assembly.

NOTICE:

Do not damage the clips (A) or (B).



Hide 6.REMOVE FRONT WHEELS

Hide 43215 7.REMOVE STEERING KNUCKLE SEAL (w/ Seal)

HINT:

Use the same procedure for both sides.


a.
C406710C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw to remove the steering knuckle seal as shown in the illustration.


Hide 45047 8.SEPARATE TIE ROD END SUB-ASSEMBLY LH

a.
C345614

Remove the cotter pin and nut.


b.
C345615N02
2.396,1.344 2.219,1.344 2.219,1.344 2.219,1.135 false 2.427,1.281 2.885,1.479 0.458,0.198 10 false SST

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper ends of the tie rod end sub-assembly LH and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.



d.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.

SST
09960-20010  (09961-02010)

C345616C02
3.427,2.479 3.427,2.094 false 1.198,1.99 1.198,1.719 1.198,1.719 1.344,1.719 false 0.458,0.729 0.865,0.719 true 0.271,0.646 0.458,0.823 0.188,0.177 10 true *a 5.531,2.281 5.844,2.438 0.313,0.156 10 false *b 6.594,0.313 6.906,0.469 0.313,0.156 10 false *c 1.375,1.625 1.688,1.781 0.313,0.156 10 false *d 5.552,2 5.865,2.156 0.313,0.156 10 false *b 0.354,2.073 0.51,2.271 0.156,0.198 10 false A 0.354,2.292 0.51,2.49 0.156,0.198 10 false B 3.323,2.51 3.792,2.719 0.469,0.208 10 false SST
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45046 9.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 10.REMOVE STEERING LINK ASSEMBLY

a.
C369027

Disconnect the connector.


b.

Remove the bolt and separate the wire harness clamp bracket from the front suspension crossmember sub-assembly.


c.
C365810

Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



d.
C365812

Remove the No. 1 steering column hole cover sub-assembly from the steering link assembly.


e.
C365814C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the steering link assembly as shown in the illustration.


Hide 11.SECURE STEERING LINK ASSEMBLY

a.
C348415C01
1.823,1.073 2.333,1.573 2.333,1.573 2.531,1.573 true 0.802,0.5 1.25,0.5 1.25,0.5 1.594,0.885 true 2.583,1.479 2.896,1.635 0.313,0.156 10 false *a 0.5,0.417 0.958,0.615 0.458,0.198 10 false SST
*a Protective Tape


Using SST, secure the steering link assembly in a vise.

SST
09612-00012  

HINT:

Wrap SST with protective tape before use.



Hide 45047 12.REMOVE TIE ROD END SUB-ASSEMBLY LH

a.
C165553C04
1.292,1.021 1.292,1.521 1.292,1.521 1.823,1.521 false 1.438,1.021 1.438,1.521 false 1.865,1.458 2.208,1.719 0.344,0.26 10 false *a
*a Matchmark


Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.


b.

Remove the tie rod end sub-assembly LH and lock nut.


Hide 45046 13.REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.