Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2019.09–2020.08
RM32K0E _55 Steering _061343 STEERING COLUMN _0299713 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the electric power steering column sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration
·

Lane departure alert system (w/ Steering Control)

·

Toyota parking assist-sensor system*1

·

Parking support brake system*1

·

Simple intelligent parking assist system*1

·

Pre-collision system


(Click here)
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Electric power steering column sub-assembly Torque sensor zero point calibration
·

DTCs are stored

·

EPS warning light illuminates


(Click here)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 73900 5.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 67914 6.REMOVE FRONT DOOR SCUFF PLATE LH (w/o Knee Airbag)

Hide 62112 7.REMOVE COWL SIDE TRIM BOARD LH (w/o Knee Airbag)

Hide 55606 8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55404D 9.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55470 10.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY (w/o Knee Airbag)

Hide 55434B 11.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL (w/o Knee Airbag)

Hide 53601 12.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55545 13.REMOVE FUSE BOX OPENING COVER (w/o Knee Airbag)

Hide 45287 14.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

NOTICE:

Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.


a.

Release the tilt and telescopic lever and fully extend and lower the steering column assembly.


b.

Lock the tilt and telescopic lever.


c.
C365770

Remove the 2 screws.


d.
C365771C02
0,0 0,0 false
V113146

Place Hand Here
V100135

Push


Push the upper steering column cover and disengage the 4 claws as shown in the illustration.


e.
C365772

Disengage the 2 claws.


f.

Release the tilt and telescopic lever and fully extend and lift the steering column assembly.


g.

Lock the tilt and telescopic lever.


h.
C365773C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Pull the lower steering column cover sub-assembly toward the rear of the vehicle to disengage the claw and remove the lower steering column cover sub-assembly.


Hide 45286B 15.REMOVE UPPER STEERING COLUMN COVER

a.

Release the tilt and telescopic lever and fully extend and lower the steering column assembly.


b.

Lock the tilt and telescopic lever.


c.
C365774C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and separate the upper steering column cover.


d.
C365775

Disengage the 2 claws and 4 clips to remove the upper steering column cover.


Hide 16.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


b.
C365776C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 claws to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 58816B 17.REMOVE CONSOLE BOX INSERT (for LHD)

Hide 87211 18.REMOVE NO. 1 AIR DUCT (for LHD)

a.
C365778

Remove the 2 bolts.


b.

Disengage the 3 claws to remove the No. 1 air duct.


Hide 58817A 19.REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

Hide 87211A 20.REMOVE NO. 2 AIR DUCT (for RHD)

a.
C365777

Remove the 2 bolts.


b.

Disengage the 3 claws to remove the No. 2 air duct.


Hide 84340 21.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 45259A 22.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C365779C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and open the column hole cover silencer sheet.


b.
C365780C01
0,0 0,0 false
V113146

Place Hand Here


Disengage the 2 claws to remove the column hole cover silencer sheet.


Hide 45260 23.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C365781C01
1.833,1.833 2.521,1.74 2.521,1.74 1.802,1.76 true 2.583,1.667 2.792,1.844 0.208,0.177 10 true *a
*a Matchmark


Put matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


b.

Remove the bolt.


c.

Separate the No. 2 steering intermediate shaft assembly from the steering gear assembly.


Hide 45260 24.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C365782C01
1.635,0.813 2.635,0.885 2.635,0.885 1.635,0.74 true 2.75,0.802 2.927,0.969 0.177,0.167 10 true *a
*a Matchmark


Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


b.

Remove the bolt.


c.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.


Hide 25.REMOVE STEERING COLUMN ASSEMBLY (for LHD)

a.
C365783

Disconnect the 2 power steering ECU connectors.


b.

Disengage the power steering ECU wire harness clamp.


c.

Disconnect each connector and disengage each clamp from the steering column assembly.


d.
C365785

Remove the bolt, 2 nuts and steering column assembly.


Hide 26.REMOVE STEERING COLUMN ASSEMBLY (for RHD)

a.
C365784

Disconnect the 2 power steering ECU connectors.


b.

Disengage the power steering ECU wire harness clamp.


c.

Disconnect each connector and disengage each clamp from the steering column assembly.


d.
C365786

Remove the bolt, 2 nuts and steering column assembly.