Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0293922 ENGINE ASSEMBLY A

2ZR-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for Nickel Metal Hydride Battery:
(Click here)
for Lithium-ion Battery:
(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
·

Replacement of throttle body assembly

·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.*2
(The vehicle height changes because of suspension or tire replacement.)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.SECURE STEERING WHEEL ASSEMBLY

Hide 6.REMOVE FRONT WHEELS

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

a.
A390450

Remove the 4 bolts, 4 screws, 4 clips and No. 1 engine under cover from the vehicle.


Hide 51444A 8.REMOVE REAR ENGINE UNDER COVER LH

a.
A394151

Remove the 6 clips and rear engine under cover LH from the vehicle.


Hide 51443C 9.REMOVE REAR ENGINE UNDER COVER RH

a.
A394150

Remove the 6 clips and rear engine under cover RH from the vehicle.


Hide 11.DRAIN ENGINE COOLANT (for Engine)

Hide 16296 13.DISCONNECT NO. 8 WATER BY-PASS HOSE

a.
A375788

Slide the clip and disconnect the No. 8 water by-pass hose from the No. 2 water by-pass hose assembly.


Hide 53141F 14.REMOVE RADIATOR COVER

Hide 17752 15.REMOVE NO. 2 AIR CLEANER INLET

Hide 22210 16.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17801 17.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 18.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 17771A 19.REMOVE AIR CLEANER BRACKET

Hide 17751 20.REMOVE NO. 1 AIR CLEANER INLET

Hide G9200 21.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 33820B 22.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C365176

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


b.

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


c.
A393200

Remove the bolt to disconnect the transmission control cable assembly from the cylinder head cover sub-assembly.


Hide 16573B 23.DISCONNECT NO. 3 RADIATOR HOSE

a.
A372567

Remove the 2 bolts from the hybrid vehicle transaxle assembly.


b.

Slide the clip and disconnect the No. 3 radiator hose from the water outlet.


Hide 16572D 24.DISCONNECT NO. 2 RADIATOR HOSE

a.
A372568

Slide the clip and disconnect the No. 2 radiator hose from the water inlet sub-assembly.


Hide 87246 25.DISCONNECT OUTLET HEATER WATER HOSE

a.
A372572

Slide the clip and disconnect the outlet heater water hose from the No. 1 water by-pass pipe.


Hide 87245A 26.DISCONNECT INLET HEATER WATER HOSE A

a.
A372573

Slide the clip and disconnect the inlet heater water hose A from the EGR pipe with cooler sub-assembly.


Hide 23826 27.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A372574

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the fuel vapor feed pipe.


Hide 23901 28.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide G922H 29.DISCONNECT INLET HYBRID RADIATOR HOSE

a.
A393197

Slide the clip and disconnect the inlet hybrid radiator hose from the motor cooling cooler.


Hide G922F 30.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.
A393198

Slide the clip and disconnect the outlet No. 1 hybrid water pump hose from the motor cooling cooler.


Hide 88703 31.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 32.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 82123 33.DISCONNECT NO. 3 ENGINE WIRE

a.
A393199

Disengage the clamp.


b.

Remove the 2 bolts and disconnect the No. 3 engine wire from the hybrid vehicle transaxle assembly.


Hide 45259A 34.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 35.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 36.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 58165B 38.REMOVE FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 57533B 39.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 40.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 51108A 42.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 43.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 44.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.
A372577

Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A372578

Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


d.
A380140

Remove the bolt and No. 2 engine mounting stay LH.


e.
A392289

Remove the 6 bolts to separate the front suspension crossmember sub-assembly from the vehicle.


f.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 45.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A379357

Disengage the 3 clamps.


b.

Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.


Hide 46.INSTALL ENGINE HANGERS

a.
A372562C01
1.75,1.083 2.063,1.083 true 1.271,1.896 1.417,1.896 1.417,1.896 1.677,1.563 true 2,3.135 2.313,3.135 true 1.385,4.229 1.531,4.229 1.531,4.229 1.792,3.896 true 2.135,1.01 2.448,1.208 0.313,0.198 10 true *1 2.385,3.042 2.698,3.24 0.313,0.198 10 true *2 1,1.802 1.25,2 0.25,0.198 10 true *3 1.104,4.146 1.354,4.344 0.25,0.198 10 true *3
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
*3 Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-37021
No. 2 Engine Hanger 12282-37011
Bolt 91552-81050



b.

Using an engine sling device and engine lifter, secure the engine assembly with transaxle.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent damage or deformation to the engine hangers or engine assembly.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 47.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A372579

Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle.


Hide 12305 48.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A379827

Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.


b.
A372580

Remove the bolt, nut and disconnect the air conditioner tube and accessory assembly.


c.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 88370 49.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

Hide 11363A 51.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 82121 52.REMOVE ENGINE WIRE

a.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 31270 54.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 56.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 57.REMOVE ENGINE HANGERS

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.