Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › from 2019.09
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0298366 TRANSMISSION CONTROL CABLE A

P610 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 51441 2.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 3.REMOVE REAR ENGINE UNDER COVER LH

Hide 33504F 4.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 5.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 57533B 6.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 7.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 58151 8.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C364049

Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body.


Hide 33820B 9.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.

for TMMT Made:

i.
C364051C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the end of the transmission control cable assembly from the floor shift shift lever assembly.


ii.
C364050C01
1.115,1.927 1.448,1.594 true 0.885,1.896 1.073,2.094 0.188,0.198 10 true *1
*1 Slider
V100135

Push
V113147

Remove in this Direction


Push in the slider and remove the transmission control cable from the shift lever assembly as shown in the illustration



c.

for TMC Made:

i.
C365188C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the end of the transmission control cable assembly from the floor shift shift lever assembly.


ii.
C365189C01
1.542,1.656 1.625,1.417 true 1.427,1.656 1.635,1.844 0.208,0.188 10 true *1
*1 Nut
V100135

Rotate approximately 180°
V113147

Remove in this Direction


Rotate the nut approximately 180° in the direction shown in the illustration, and while holding the nut in that position, disconnect the transmission control cable assembly from the shift lever plate.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.




d.
C365176

Remove the nut to disconnect the transmission control cable assembly from the control shaft lever.


e.

Remove the clip to disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


f.
C366448

Disengage the clamp to separate the transmission control cable assembly.


g.

Remove the bolt to disconnect the transmission control cable assembly from the cylinder head cover sub-assembly.


h.
C365141

Remove the nut.


i.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


j.
C365142

Remove the 2 nuts and transmission control cable assembly from the vehicle body.