Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER › from 2019.09
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0293793 SHIFT LEVER A

P610 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 33530F 1.INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY (for RHD)

C368572N01
0.927,1.979 1.083,2.177 0.156,0.198 10 true 1 2.302,0.49 2.458,0.688 0.156,0.198 10 true 2 0.917,0.49 1.073,0.688 0.156,0.198 10 true 3 2.25,1.979 2.406,2.177 0.156,0.198 10 true 4

a.

Temporarily install the floor shift shift lever assembly to the body with the 4 bolts.


b.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

w/ Stereo Component Amplifier:

i.

Engage the 5 clamps to install the wire harness to the floor shift shift lever assembly.


ii.

Connect the 2 connectors to the floor shift shift lever assembly.



d.

w/o Stereo Component Amplifier:

i.

Engage the 4 clamps to install the wire harness to the floor shift shift lever assembly.


ii.

Connect the 2 connectors to the floor shift shift lever assembly.



Hide 33530F 2.INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY (for LHD)

C368571N01
0.927,1.979 1.083,2.177 0.156,0.198 10 true 1 2.313,0.5 2.469,0.698 0.156,0.198 10 true 2 0.958,0.479 1.115,0.677 0.156,0.198 10 true 3 2.281,1.979 2.438,2.177 0.156,0.198 10 true 4

a.

Temporarily install the floor shift shift lever assembly to the body with the 4 bolts.


b.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Engage the 6 clamps to install the wire harness to the floor shift shift lever assembly.


d.

Connect the 2 connectors to the floor shift shift lever assembly.


Hide 33820B 3.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

for TMMT Made:

i.
C366437C01
0,0 0,0 false
V113147

Install in this Direction


Connect the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:

Make sure that the transmission control cable assembly is securely locked.



ii.
C366436C02
0,0 0,0 false
V113147

Install in this Direction


Connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Before connecting the transmission control cable assembly, check that the park/neutral position switch and shift lever are in N.

·

Install the end of the transmission control cable assembly so that the lock piece faces the driver side.

·

Install the end of the transmission control cable assembly all the way to the base of the pin.





b.

for TMC Made:

i.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut in that position, push in the lock.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.



ii.
C365195C01
0.792,2.531 0.604,2.344 false 2.813,2.542 2.625,2.354 false 2.458,2.26 2.771,2.417 0.313,0.156 10 false *1 0.458,2.229 0.771,2.385 0.313,0.156 10 false *a 0.313,2.5 0.5,2.656 0.188,0.156 10 false A 1.24,2.51 1.427,2.667 0.188,0.156 10 false A
*1 Lock
*a Protrusion
V113147

Install in this Direction


Install the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.

·

Make sure that the transmission control cable assembly is securely locked.




iii.
C365194C01
0,0 0,0 false
V113147

Install in this Direction


Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the floor shift shift lever assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.





Hide 58995A 5.INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET

a.

w/ Stereo Component Amplifier:

i.

Install the No. 1 console box mounting bracket to the vehicle body with the 2 bolts.


ii.

Engage the 3 clamps to install the wire harness to the No. 1 console box mounting bracket.



b.

w/o Stereo Component Amplifier:

i.

Install the No. 1 console box mounting bracket to the vehicle body with the 2 bolts.


ii.

Engage the 2 clamps to install the wire harness to the No. 1 console box mounting bracket.



Hide 86741A 6.INSTALL TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

Hide 33504F 8.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 9.INSTALL SHIFT LEVER CAP

a.

Engage the 2 claws to install the shift lever cap to the shift position indicator.