Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2019.09
RM32K0E _51 Engine / Hybrid System _083976 M20A-FXS ENGINE MECHANICAL _0404776 REAR CRANKSHAFT OIL SEAL A

M20A-FXS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




c.
A426062C01
1.125,1.458 0.625,1.188 0.625,1.188 1.51,0.854 true 0.292,1.115 0.75,1.313 0.458,0.198 10 false SST 2.208,2.104 2.521,2.302 0.313,0.198 10 false *a
*a -0.9 to 1.1 mm


Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Standard Depth:

-0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)


NOTICE:

Do not tap in the rear engine oil seal at an angle.



Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A426063

Install the No. 1 crankshaft position sensor plate.

HINT:

Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.



Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A434751N01
1.417,0.885 2.125,0.531 2.125,0.531 1.823,0.833 true 2.167,0.396 2.625,0.594 0.458,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.

Clean the bolt holes.


c.

Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A434748N01
2.229,0.427 2.385,0.625 0.156,0.198 10 true 1 2.427,0.885 2.583,1.083 0.156,0.198 10 true 3 1.646,1.719 1.802,1.917 0.156,0.198 10 true 7 2.208,1.458 2.365,1.656 0.156,0.198 10 true 5 1.073,1.5 1.229,1.698 0.156,0.198 10 true 2 0.844,0.885 1,1.083 0.156,0.198 10 true 4 1.052,0.396 1.188,0.594 0.135,0.198 10 true 6 1.625,0.104 1.781,0.302 0.156,0.198 10 true 8

Install the flywheel sub-assembly with the 8 new bolts. Uniformly tighten the 8 bolts in the order shown in the illustration.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.



Hide 31270 4.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.
A434751N02
1.406,0.854 2.125,0.521 2.125,0.521 1.844,0.833 true 2.188,0.396 2.646,0.594 0.458,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.
A406362N02
1.292,0.052 1.448,0.25 0.156,0.198 10 true 1 2.552,0.385 2.708,0.583 0.156,0.198 10 false 3 2.729,1.417 2.885,1.615 0.156,0.198 10 false 5 1.99,1.969 2.146,2.167 0.156,0.198 10 false 2 0.792,1.771 0.948,1.969 0.156,0.198 10 false 4 0.542,0.719 0.698,0.917 0.156,0.198 10 true 6

Install the transmission input damper assembly to the flywheel sub-assembly with the 6 bolts. Uniformly tighten the 6 bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Make sure that there are no oil on the transmission input damper assembly and flywheel sub-assembly.

·

Make sure to install the transmission input damper assembly in the correct direction.

·

Do not allow grease to contact the splines of the transmission input damper assembly and the input shaft.




Hide 30900 5.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY