Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › from 2019.09
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0292760 HYBRID VEHICLE TRANSAXLE A

P610 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1.INSTALL TRANSAXLE HOUSING PLUG

a.

Install the transaxle housing plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 3 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 44781E 3.INSTALL HOSE BRACKET

a.

Install the hose bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 33823 4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide G1251B 5.INSTALL NO. 1 MOTOR COOLING PIPE

a.

Temporarily install the No. 1 motor cooling pipe to the union with the flare nut.


b.

Install the No. 1 oil cooler tube clamp to the hose bracket with the bolt.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


c.
C365159C01
2.719,1.74 3.031,1.896 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the flare nut to install the No. 1 motor cooling pipe.

Torque:
Specified Tightening Torque : 34.3 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

29.4 N*m (300 kgf*cm, 22 ft.*lbf)




Hide G125A 6.INSTALL MOTOR COOLING COOLER

a.
C365166N01
1.917,1.979 2.073,2.177 0.156,0.198 10 true 1 1.042,0.792 1.198,0.99 0.156,0.198 10 true 2 1.844,0.823 2,1.021 0.156,0.198 10 true 3

Temporarily install the motor cooling cooler with No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


c.

Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the union bolt and a new gasket.


d.

Install the No. 1 oil cooler tube clamp to the hose bracket with the bolt.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


e.

Tighten the union bolt to install the No. 2 motor cooling pipe.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


f.
C343168C01
2.729,1 2.479,0.938 2.479,0.938 2.708,0.906 true 3.052,1.25 3.302,1.448 0.25,0.198 10 false *a 2.323,0.865 2.542,1.042 0.219,0.177 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Connect the No. 1 motor cooling hose to the No. 1 motor cooling pipe and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 1 motor cooling pipe with the paint mark on the No. 1 motor cooling hose.



Hide 12364B 8.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C343179N01
1.219,1.708 1.375,1.906 0.156,0.198 10 false C 2.167,0.833 2.313,1.01 0.146,0.177 10 true C 1.313,0.74 1.458,0.917 0.146,0.177 10 true A 1.74,1.813 1.885,1.99 0.146,0.177 10 true B

Install the No. 2 engine moving control rod to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 4 bolts in the order of (B), (C) and (A).



Hide 51201 9.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Install the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


Hide 10.INSTALL ENGINE ASSEMBLY

a.
C350365C01
0.708,0.396 0.906,0.563 0.198,0.167 10 true *1 2.75,0.667 2.948,0.833 0.198,0.167 10 true *1
*1 Knock Pin


Make sure that the knock pins are installed to the engine assembly.


b.
C343177N01
1.156,0.25 1.302,0.427 0.146,0.177 10 true A 2.427,0.229 2.573,0.406 0.146,0.177 10 false B 0.896,0.927 1.042,1.115 0.146,0.188 10 true C 1.115,1.823 1.26,2.01 0.146,0.188 10 true C 2.292,2 2.438,2.177 0.146,0.177 10 true C 2.573,1.979 2.719,2.167 0.146,0.188 10 true C 1.458,2.01 1.604,2.177 0.146,0.167 10 true C

Install the engine assembly to the hybrid vehicle transaxle assembly with the 7 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly are in close contact with one another.

·

Temporarily tighten the bolt (A), and then fully tighten the 7 bolts in the order of (B), (A) and (C).

·

Do not apply grease to the inner splines of the transmission input damper assembly or input shaft assembly.

·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excessive force when installing the hybrid vehicle transaxle assembly.

·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft assembly of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.

·

When inserting the input shaft assembly of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the hybrid vehicle transaxle assembly excessively.

·

When installing the hybrid vehicle transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock pin holes.




Hide 11363A 11.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the engine assembly.


Hide 28193 12.INSTALL STARTER HOLE INSULATOR

a.

Install the starter hole insulator to the engine assembly with the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 821H2 13.CONNECT HV AIR CONDITIONING WIRE

a.

Engage the guide to connect the HV air conditioning wire to the hybrid vehicle transaxle assembly.


b.

Install the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 82121 14.CONNECT ENGINE WIRE

a.

Engage the 2 clamps to connect the engine wire to the hybrid vehicle transaxle assembly.

C365164C02
2.531,1.521 2.729,1.698 0.198,0.177 10 true *a 1.844,1.396 2.042,1.573 0.198,0.177 10 true *b 2.281,0.531 2.469,0.708 0.188,0.177 10 true *c 4.49,0.896 4.646,1.094 0.156,0.198 10 true A 5.958,1.781 6.115,1.979 0.156,0.198 10 true B
*a Motor Revolution Sensor Wire Connector *b Shift Lever Position Sensor
*c Motor Temperature Sensor Connector - -



b.

Install the 2 bolts.

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Connect the motor temperature sensor connector.


d.

Confirm that no foreign matter or water has entered the connector of the shift lever position sensor and connect the connector.


e.

Connect the motor revolution sensor wire connector.


Hide 15.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 16. PERFORM RESOLVER LEARNING

NOTICE:

If the hybrid vehicle transaxle assembly, make sure to perform resolver learning.

for NICKEL METAL HYDRIDE BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY

for LITHIUM-ION BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY