Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083976 M20A-FXS ENGINE MECHANICAL _0404776 REAR CRANKSHAFT OIL SEAL A

M20A-FXS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Clear zero point calibration data

2.

Perform yaw rate and acceleration sensor zero point calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 2.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A434746N03
1.188,0.729 0.75,0.76 0.75,0.76 1.385,1.333 false 0.354,0.677 0.813,0.875 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A434747

Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.


Hide 13405 3.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A434746N03
1.188,0.729 0.75,0.76 0.75,0.76 1.385,1.333 false 0.354,0.677 0.813,0.875 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.
A434748

Remove the 8 bolts and flywheel sub-assembly from the crankshaft.


Hide 19315 4.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A426060

Remove the No. 1 crankshaft position sensor plate.


Hide 11401L 5.REMOVE REAR ENGINE OIL SEAL

a.
A426061C01
2.99,1.458 3.177,0.771 true 1.625,1.615 1.354,1.292 true 2.917,1.49 3.229,1.688 0.313,0.198 10 false *b 1.646,1.531 1.865,1.729 0.219,0.198 10 true *a
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.