Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › THROTTLE BODY › from 2019.09
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404835 THROTTLE BODY A

M20A-FXS ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 22271 1.INSTALL THROTTLE BODY GASKET

a.
A439248C01
1.063,0.615 1.365,0.615 true 0.771,0.531 1.031,0.74 0.26,0.208 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusion of the throttle body gasket oriented as shown in the illustration.


Hide 22030 2.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A439249C01
2.073,3.104 2.323,2.896 true 2.115,2.323 2.427,2.479 0.313,0.156 10 false *a 2.802,2.802 3.115,2.958 0.313,0.156 10 false *b 2.698,2.563 3.01,2.719 0.313,0.156 10 false *c 1.938,3.115 2.25,3.271 0.313,0.156 10 false *d 2.677,3.083 2.99,3.24 0.313,0.156 10 false *c
*a Top of Vehicle
*b Left Side of Vehicle
*c 45° (Claw of Clip Location)
*d Paint Mark


Connect the No. 5 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:
·

If the throttle body with motor assembly has been struck or dropped, replace it.

·

Make sure to position the clip as shown in the illustration.




b.
A439250C01
1.365,2.885 1.615,3.146 true 1.156,2.281 1.469,2.438 0.313,0.156 10 false *a 1.802,2.865 2.115,3.021 0.313,0.156 10 false *b 1.708,2.656 2.021,2.813 0.313,0.156 10 false *c 1.646,3.083 1.958,3.24 0.313,0.156 10 false *d 1.406,2.344 1.719,2.5 0.313,0.156 10 false *c
*a Top of Vehicle
*b Left Side of Vehicle
*c 45° (Claw of Clip Location)
*d Paint Mark


Using an 8 mm socket wrench, install the throttle body with motor assembly to the intake manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 8 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



d.

Connect the throttle body with motor assembly connector.


Hide 3.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A439251C01
0.49,2.833 0.573,2.417 0.573,2.417 0.719,2.417 true 0.74,3.167 0.74,3.01 0.74,3.01 0.927,2.885 true 0.76,0.677 0.76,0.24 0.76,0.24 1,0.24 true 0.76,2.313 1.073,2.469 0.313,0.156 10 false *a 0.688,3.167 1,3.323 0.313,0.156 10 false *b 2.313,0.146 2.625,0.302 0.313,0.156 10 false *c 3.042,0.563 3.354,0.719 0.313,0.156 10 false *d 2.802,2.344 3.115,2.5 0.313,0.156 10 false *c 2.26,2.896 2.573,3.052 0.313,0.156 10 false *d 2.938,0.323 3.25,0.479 0.313,0.156 10 false *e 2.948,0.823 3.26,0.979 0.313,0.156 10 false *e 1.031,0.135 1.344,0.385 0.313,0.25 10 false *1
*1 No. 2 Ventilation Hose
*a Protrusion
*b Cutout
*c Top of Vehicle
*d Front of Vehicle
*e 45° (Claw of Clip Location)


Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly and tighten the hose clamp.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)

NOTICE:

Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly as shown in the illustration.



b.

Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



c.

Engage the 2 guides and 2 clamps.


d.

Engage the wire harness clamp and connect the mass air flow meter connector.


Hide 4.ADD ENGINE COOLANT (for Engine)

Hide 5.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51444A 6.INSTALL REAR ENGINE UNDER COVER LH

Hide 7.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

·

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.



a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

f.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

g.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard Idle Speed:

1050 to 1150 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P.




h.

Perform a road test and confirm that there are no abnormalities.