Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2019.09
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the dynamic radar cruise control or brake hold control operating signal from the skid control ECU (brake booster with master cylinder assembly), the relay contact turns on and the stop lights come on.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1380 Stop Light Control Relay Malfunction 761
762
·

INF Code: 761

-

When terminal IG1 voltage is 9.5 V or more, stop light drive output (STP0) is ON and STP2 is OFF for 2 seconds or more.


·

INF Code: 762

-

When terminal IG1 voltage is 9.5 V or more, stop light drive output (STP0) is OFF and the input signals for STP and STP2 differ for 5 seconds or more.



·

STOP fuse

·

Harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake booster with master cylinder assembly)


VSC DTC

WIRING DIAGRAM

C416913E02
4.771,8.344 6.531,8.594 1.76,0.25 10 false : CAN Communication Line 4.219,6.521 6.802,7.031 2.583,0.51 10 false Millimeter Wave Radar Sensor Assembly 4.51,5.333 4.969,5.531 0.458,0.198 10 false A39 4.521,5.479 6.604,5.99 2.083,0.51 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.948,4.469 5.406,4.667 0.458,0.198 10 false STP 4.927,3.469 5.385,3.667 0.458,0.198 10 false STPO 4.938,2.583 5.396,2.781 0.458,0.198 10 false STP2 4.656,2.583 4.969,2.781 0.313,0.198 10 false 37 4.635,3.5 4.948,3.698 0.313,0.198 10 false 22 4.646,4.469 4.958,4.667 0.313,0.198 10 false 12 1.083,8.385 2.677,8.594 1.594,0.208 10 false M115*3, q1*4, q2*5 1.073,8.542 4.135,8.74 3.063,0.198 10 false Rear Combination Light Assembly LH 1.833,7.865 1.99,8.063 0.156,0.198 10 false E 2.75,7.865 2.906,8.063 0.156,0.198 10 false B 2.948,7.854 3.104,8.052 0.156,0.198 10 false 1 2.948,6.74 3.104,6.938 0.156,0.198 10 false 1 2.74,6.771 2.896,6.969 0.156,0.198 10 false B 1.823,6.781 1.979,6.979 0.156,0.198 10 false E 1.604,6.771 1.76,6.969 0.156,0.198 10 false 3 1.052,7.281 2.427,7.469 1.375,0.188 10 false M114*3, o1*4, o2*5 1.042,7.438 4.104,7.635 3.063,0.198 10 false Rear Combination Light Assembly RH 1.552,6.146 1.865,6.344 0.313,0.198 10 false c1 1.552,6.313 3.698,6.51 2.146,0.198 10 false Center Stop Light Assembly 1.625,5.698 1.781,5.896 0.156,0.198 10 false 2 1.833,5.698 2.146,5.896 0.313,0.198 10 false E2 2.688,5.698 3,5.896 0.313,0.198 10 false B2 2.948,5.698 3.104,5.896 0.156,0.198 10 false 1 1.688,5.073 2.146,5.271 0.458,0.198 10 false A91 1.656,5.229 3.5,5.427 1.844,0.198 10 false Stop Light Switch Assembly 1.75,4.479 2.208,4.677 0.458,0.198 10 false GND 1.531,4.479 1.688,4.677 0.156,0.198 10 false 2 1.76,2.906 1.917,3.104 0.156,0.198 10 false B 1.531,2.896 1.688,3.094 0.156,0.198 10 false 7 3.104,2.583 3.26,2.781 0.156,0.198 10 false L 3.333,2.583 3.49,2.781 0.156,0.198 10 false 3 2.948,3.5 3.406,3.698 0.458,0.198 10 false ACC 3.344,3.49 3.5,3.688 0.156,0.198 10 false 4 2.979,4.458 3.438,4.656 0.458,0.198 10 false OUT 3.344,4.438 3.5,4.635 0.156,0.198 10 false 1 0.792,3.167 1.406,3.365 0.615,0.198 10 false STOP 0.469,3.875 1.354,4.26 0.885,0.385 10 false from Auxiliary Battery 4.74,0.531 5.198,0.729 0.458,0.198 10 false A49 4.719,0.698 6.76,0.979 2.042,0.281 10 false Hybrid Vehicle Control ECU*2 4.917,0.167 5.229,0.365 0.313,0.198 10 false 15 2.448,0.198 2.76,0.396 0.313,0.198 10 false 25 5.198,0.323 5.656,0.521 0.458,0.198 10 false STP 1.99,0.302 2.448,0.5 0.458,0.198 10 false STP1 1.094,0.531 1.552,0.729 0.458,0.198 10 false M67 1.073,0.708 2.896,1.073 1.823,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.604,7.865 1.76,8.063 0.156,0.198 10 false 3 3.969,6.906 5.25,7.208 1.281,0.302 10 false *1: for M20A-FXS 3.969,7.271 5.063,7.656 1.094,0.385 10 false *2: for 2ZR-FXE 4.76,1.563 5.219,1.76 0.458,0.198 10 false A97 4.75,1.729 6.792,2.01 2.042,0.281 10 false Hybrid Vehicle Control ECU*1 4.281,1.219 4.74,1.417 0.458,0.198 10 false *1 4.281,0.167 4.74,0.365 0.458,0.198 10 false *2 5.177,1.344 5.635,1.542 0.458,0.198 10 false STP 4.969,1.229 5.281,1.427 0.313,0.198 10 false 7 3.969,7.635 5.25,7.938 1.281,0.302 10 false *3: for TMC Made 5.292,6.917 7.094,7.323 1.802,0.406 10 false *4: for TMMT Made with Triple Beam Headlight 5.281,7.552 7.073,8.01 1.792,0.458 10 false *5: for TMMT Made with Single Beam Headlight

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STP, STPO AND STP2 TERMINAL)
a.

Turn the power switch off.


b.
C343117C97
0.375,0.792 0.75,1.042 0.375,0.25 2.271,1.604 2.385,0.948 true 2.063,1.885 1.698,0.979 true 2.854,2.781 2.198,2.052 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 0.448,0.823 0.833,1.042 0.385,0.219 10 false A39 2.406,0.781 2.844,1.01 0.438,0.229 10 false STP 1.344,0.792 1.813,1.021 0.469,0.229 10 false STPO 2.885,2.802 3.354,3.031 0.469,0.229 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-12 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V
A39-22 (STPO) - Body ground Always 11 to 14 V
A39-37 (STP2) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V



Result:
Result Proceed to
All terminal voltage is normal A
Only STP2 terminal voltage abnormal B
Only STPO terminal voltage abnormal C
Only STP terminal voltage abnormal D
STPO terminal and STP2 terminal voltage abnormal E



A

2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

B

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

C

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

D

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

E

14.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform "Active Test" according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON or OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5
OK:

Stop light turns ON/OFF in response to the GTS operation



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
3.CHECK FOR DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


c.

Perform "Active Test" according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON or OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

d.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

Result:
Result Proceed to
DTC C1380 is output (for LHD) A
DTC C1380 is output (for RHD) B
DTC C1380 is not output C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform "Active Test" according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON or OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.
C401043C60
0.417,0.656 0.76,0.885 0.344,0.229 0.969,1.635 1.688,1.052 true 0.469,0.677 0.927,0.875 0.458,0.198 10 false A91 0.188,0.188 0.646,0.385 0.458,0.198 10 false *a 0.604,1.594 1.063,1.792 0.458,0.198 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-4 (ACC) - Body ground Active Test is ON Below 1.5 V



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

REPLACE STOP LIGHT SWITCH ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.
C375632C01
1.5,0.438 1.906,0.698 0.406,0.26 2.51,2.885 2.188,2.063 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 1.573,0.5 2.031,0.698 0.458,0.198 10 false A39 2.365,2.938 2.979,3.135 0.615,0.198 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A49*1 or A97*2 hybrid vehicle control ECU connector.

*1: for 2ZR-FXE

*2: for M20A-FXS



c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A39-37 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Result Proceed to
OK (for 2ZR-FXE) A
OK (for M20A-FXS) B
NG C



A

B

C

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SMART KEY ECU ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.
C375632C01
1.5,0.438 1.906,0.698 0.406,0.26 2.51,2.885 2.188,2.063 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 1.573,0.5 2.031,0.698 0.458,0.198 10 false A39 2.365,2.938 2.979,3.135 0.615,0.198 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the M67 certification ECU (smart key ECU assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-37 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V
A39-37 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A91 stop light switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-22 (STPO) - A91-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C375632C01
1.5,0.438 1.906,0.698 0.406,0.26 2.51,2.885 2.188,2.063 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 1.573,0.5 2.031,0.698 0.458,0.198 10 false A39 2.365,2.938 2.979,3.135 0.615,0.198 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A91 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-37 (STP2) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A91 stop light switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-37 (STP2) - A91-3 (L) Always Below 1 Ω
A39-37 (STP2) or A91-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.

Turn the power switch off.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the M115*1, q1*2 or q2*3 rear combination light assembly LH connector.


*1: for TMC Made

*2: for TMMT Made with Triple Beam Headlight

*3: for TMMT Made with Single Beam Headlight


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-12 (STP) - Body ground Brake pedal depressed 11 to 14 V
A39-12 (STP) - Body ground Brake pedal released Below 1.5 V



Result:
Result Proceed to
OK (for LED Type) A
OK (for Bulb Type) B
NG C



A

B

C

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
a.

Turn the power switch off.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the M115*1, q1*2 or q2*3 rear combination light assembly LH connector.


*1: for TMC Made

*2: for TMMT Made with Triple Beam Headlight

*3: for TMMT Made with Single Beam Headlight


d.

Disconnect the M114*1, o1*2 or o2*3 rear combination light assembly RH connector.


*1: for TMC Made

*2: for TMMT Made with Triple Beam Headlight

*3: for TMMT Made with Single Beam Headlight


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-12 (STP) - Body ground Brake pedal depressed 11 to 14 V
A39-12 (STP) - Body ground Brake pedal released Below 1.5 V



Result:
Result Proceed to
OK (for LED Type) A
OK (for Bulb Type) B
NG C



A

B

C

12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the M115*1, q1*2 or q2*3 rear combination light assembly LH connector.


*1: for TMC Made

*2: for TMMT Made with Triple Beam Headlight

*3: for TMMT Made with Single Beam Headlight


d.

Disconnect the M114*1, o1*2 or o2*3 rear combination light assembly RH connector.


*1: for TMC Made

*2: for TMMT Made with Triple Beam Headlight

*3: for TMMT Made with Single Beam Headlight


e.

Disconnect the c1 center stop light assembly connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-12 (STP) - Body ground Brake pedal depressed 11 to 14 V
A39-12 (STP) - Body ground Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

13.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
13.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the M115*1, q1*2 or q2*3 rear combination light assembly LH connector.


*1: for TMC Made

*2: for TMMT Made with Triple Beam Headlight

*3: for TMMT Made with Single Beam Headlight


d.

Disconnect the M114*1, o1*2 or o2*3 rear combination light assembly RH connector.


*1: for TMC Made

*2: for TMMT Made with Triple Beam Headlight

*3: for TMMT Made with Single Beam Headlight


e.

Disconnect the c1 center stop light assembly connector.


f.

Disconnect the A91 stop light switch assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-1 (OUT) - A39-12 (STP) Always Below 1 Ω
A91-1 (OUT) or A39-12 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
a.

Turn the power switch off.


b.
C401044C62
0.49,0.646 0.833,0.854 0.344,0.208 2.167,1.219 2.396,1.698 true 1.427,1.229 1.281,1.656 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A91 1.146,1.698 1.563,1.896 0.417,0.198 10 false GND 2.385,1.729 2.802,1.927 0.417,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-2 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the power switch off.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A91 stop light switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-22 (STPO) - A91-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR