Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD) › 2019.09–2020.08
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294925 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of brake actuator assembly
1.

Bleed air

2.

Clear the data stored during previous linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

3.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for Calibration:(Click here)

CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55736D 5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 51410 8.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for M20A-FXS)

Hide 9.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide 10.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 82111 11.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C366571C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


for 2ZR-FXE:

i.

Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




b.

for M20A-FXS:

i.
C410336C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




c.
C366572C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



d.

Disengage the clamp and separate the engine room main wire.


Hide 55225 12.REMOVE DASH PANEL HEAT INSULATOR (for M20A-FXS)

Hide 88707 13.SEPARATE SUCTION PIPE SUB-ASSEMBLY

a.
C366567

Disengage the 2 clamps to separate the suction pipe sub-assembly.


b.
C366568

Remove the bolt and rotate the hook connector.


c.

Disconnect the suction pipe sub-assembly from the air conditioning unit assembly.


d.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 14.SEPARATE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.
C366569

Disengage the 2 clamps to separate the air conditioner tube and accessory assembly.


b.
C366570

Disconnect the air conditioner tube and accessory assembly from the air conditioning unit assembly.


c.

Remove the O-ring from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 44571A 15.SEPARATE NO. 1 BRAKE ACTUATOR HOSE

a.
C366573

Slide the clip and disconnect the No. 1 brake actuator hose from the No. 1 brake actuator tube.


b.
C366574

Separate the No. 1 brake actuator hose from the brake actuator hose clamp.


Hide 16.SEPARATE BRAKE LINE

a.
C366575C01
2.167,1.083 2.417,0.833 2.417,0.833 2.583,0.833 true 1.896,0.854 2.083,0.333 2.083,0.333 2.25,0.333 true 1.698,0.979 1.5,0.25 1.5,0.25 1.333,0.25 true 1.563,1.156 1.083,0.583 1.083,0.583 0.917,0.583 true 1.458,1.375 1.25,1.583 1.25,1.583 1.083,1.583 true 1.667,1.917 1.677,1.563 true 1.594,1.927 1.833,2.083 0.24,0.156 10 true *a 2.625,0.719 2.792,0.885 0.167,0.167 10 true *b 0.833,1.469 1.063,1.656 0.229,0.188 10 true *c 0.688,0.479 0.917,0.635 0.229,0.156 10 true *d 1.125,0.135 1.333,0.323 0.208,0.188 10 true *e 2.281,0.24 2.448,0.417 0.167,0.177 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake lines.


b.
C366576

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


Hide 473A1 17.SEPARATE ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C366577

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.


b.

Remove the bolt to separate the accumulator to brake master cylinder tube.


Hide 47070 18.SEPARATE BRAKE BOOSTER PUMP ASSEMBLY

a.
C366578

for 2ZR-FXE:

i.

Disengage the claw and clamp to separate the brake booster pump assembly wire harness from the brake actuator bracket assembly.



b.

for M20A-FXS:

i.
C410466

Disengage the clamp to separate the brake booster pump assembly wire harness from the brake actuator bracket assembly.



c.
C366579C01
0,0 0,0 false
V113147

Move in this Direction


Remove the nut to separate the brake booster pump assembly from the brake actuator bracket assembly.

HINT:

Move the brake booster pump assembly to the position where the lower bolt of the brake actuator assembly can be removed.



Hide 44510 19.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C366580

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not apply excessive force to the brake lines or refrigerant lines.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.