The skid control ECU (brake booster with master cylinder assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.
The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1425 | Open in Stop Switch Circuit | 231 | An open stop light switch circuit continues for 10 seconds or more. | ·
Wire harness or connector ·
Stop light switch assembly ·
Skid control ECU (brake booster with master cylinder assembly) ·
Stop light circuit |
Electronically controlled brake system DTC |
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Check that the stop lights come on when the brake pedal is depressed.
| Result | Proceed to |
|---|---|
| All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. | A |
| All stop lights do not illuminate when the brake pedal is depressed. | B |
| One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. | C |
A
B
C
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light SW |
Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.
The GTS displays on or off according to brake pedal operation.
| Result | Proceed to |
|---|---|
| The value of Stop Light SW is ON. | A |
| Other than above. | B |
A
B
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Turn the power switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A91-1 (OUT) - Body ground | ·
Power switch on (IG) ·
The headlights are on ·
The blower motor switch is in the HI position ·
The rear window defogger is turned on ·
Stop light switch assembly off (Brake pedal released) |
1.5 V or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch off.
Turn the power switch on (READY).
Perform a road test.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTC C1425 is not output. | A |
| DTC C1425 is output. (for LHD) | B |
| DTC C1425 is output. (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Turn the power switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A91 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A91-1 (OUT) - Body ground | Stop light switch assembly off
(Brake pedal released) |
1.5 V or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A91-1 (OUT) - Body ground | Stop light switch assembly off
(Brake pedal released) |
1.5 V or less |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Check that there is no short to +B in the STP circuit (wire harnesses, connectors and stop lights).
No short to +B.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Turn the power switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-12 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.
No open.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C