Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2ZR-FXE) › from 2019.09
RM32K0E _52 Drivetrain _061224 DRIVE SHAFT / PROPELLER SHAFT _0405859 FRONT DRIVE SHAFT ASSEMBLY(for 2ZR-FXE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2ZR-FXE)  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER

a.
C235587C07
0.635,0.323 0.948,0.604 false 0.448,1.063 0.74,1.313 false 0.469,0.208 0.781,0.365 0.313,0.156 10 false *a 0.135,0.948 0.594,1.146 0.458,0.198 10 false SST
*a Steel Plate


Using SST, a steel plate and a press, install a new front drive shaft dust cover.

SST
09527-10011  

NOTICE:
·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover.

·

Install the front drive shaft dust cover LH in the correct direction.




Hide 2.INSTALL FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

a.
C177228C09
2.01,0.885 2.427,1.156 false 2.49,1.083 2.802,1.24 0.313,0.156 10 false *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard grease capacity (for TMMT made):

90 to 110 g (3.17 to 3.88 oz)


Standard grease capacity (for TMC made):

135 to 145 g (4.76 to 5.11 oz)



d.

Install the front axle outboard joint boot into the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 3.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for TMMT Made LH Side)

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle outboard joint boot clamp onto the front axle outboard joint boot.


c.
C282247C01
2.156,1 2.531,0.76 false 2.563,0.667 3.021,0.865 0.458,0.198 10 false SST 1.677,0.021 1.99,0.177 0.313,0.156 10 false *a 2.552,1.573 2.865,1.729 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C282248E01
1.625,1.063 0.938,1.406 true 0.656,1.323 1.115,1.521 0.458,0.198 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)



Hide 43447F 4.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for TMC Made LH Side)

CAUTION:
·
C331975

When installing the front No. 2 axle outboard joint boot clamp, do not perform the work without wearing protective gloves.

·

If work is performed without using protective gloves, injuries may occur.



a.
C415871C01
2.156,1.5 2.677,1.5 false 0.833,1.24 1.354,1.24 false 1.917,2.031 2.438,2.031 false 2.708,1.438 3.021,1.594 0.313,0.156 10 false *a 0.667,1.177 0.979,1.333 0.313,0.156 10 false *b 1.729,1.948 2.042,2.104 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




b.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415872C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C265825C09
1.698,3.74 1.135,4.417 1.135,4.417 1.896,3.771 true 0.979,4.406 1.292,4.604 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.




Hide 43447E 5.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for TMMT Made LH Side)

a.

Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.


b.
C282249C01
2.219,1.281 2.76,1.073 false 2.802,0.979 3.26,1.177 0.458,0.198 10 false SST 1.781,0.042 2.094,0.198 0.313,0.156 10 false *a 2.49,1.792 2.802,1.948 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C282250E01
1.542,1.531 2.177,1.656 true 2.229,1.583 2.688,1.781 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43447E 6.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for TMC Made LH Side)

CAUTION:
·
C331975

When installing the front axle outboard joint boot clamp, do not perform the work without wearing protective gloves.

·

If work is performed without using protective gloves, injuries may occur.



a.
C107948

Install the front axle outboard joint boot clamp to the front axle outboard joint boot and provisionally bend the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and lever for any deformation before bending the lever.




b.
C112271C02
2.292,1.854 2.344,1.396 false 2.229,1.854 2.542,2.01 0.313,0.156 10 false *a
*a Place the tip near the center of the lever


Using water pump pliers, pinch the front axle outboard joint boot clamp to provisionally fix it.


c.

Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.

NOTICE:

Do not damage the front axle outboard joint boot.



Hide 43474E 7.INSTALL FRONT DRIVE SHAFT DAMPER LH (for TMMT Made)

a.
C360105C04
0.219,1.625 0.219,1.292 false 0.75,1.719 0.75,1.385 false 1.333,1.625 1.333,1.292 false 2.271,1.813 2.271,1.479 false 2.188,1.865 2.5,2.021 0.313,0.156 10 false *1 0.677,1.771 0.99,1.927 0.313,0.156 10 false *2 0.146,1.667 0.458,1.823 0.313,0.156 10 false *3 1.25,1.677 1.563,1.833 0.313,0.156 10 false *3 1.708,0.271 2,0.479 0.292,0.208 10 false (A)
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper LH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper LH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):

184 to 188 mm (7.24 to 7.40 in.)



c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps to the front drive shaft damper LH.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C304762

Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.


Hide 43474E 8.INSTALL FRONT DRIVE SHAFT DAMPER LH (for TMC Made)

a.
C354588C09
0.198,1.292 0.198,1.552 false 0.802,1.333 0.802,1.594 false 1.385,1.281 1.385,1.542 false 2.24,1.448 2.24,1.708 false 1.479,0.594 1.938,0.792 0.458,0.198 10 false (A) 2.188,1.719 2.5,1.875 0.313,0.156 10 false *1 0.729,1.615 1.042,1.771 0.313,0.156 10 false *2 1.323,1.563 1.635,1.719 0.313,0.156 10 false *3 0.146,1.573 0.458,1.729 0.313,0.156 10 false *3
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper LH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper LH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):

211.7 to 215.7 mm (8.34 to 8.49 in.)



c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps to the front drive shaft damper LH.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C304762

Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.


Hide 43474D 9.INSTALL FRONT DRIVE SHAFT DAMPER RH (for TMC Made)

a.
C354588C09
0.198,1.292 0.198,1.552 false 0.802,1.333 0.802,1.594 false 1.385,1.281 1.385,1.542 false 2.24,1.448 2.24,1.708 false 1.479,0.594 1.938,0.792 0.458,0.198 10 false (A) 2.188,1.719 2.5,1.875 0.313,0.156 10 false *1 0.729,1.615 1.042,1.771 0.313,0.156 10 false *2 1.323,1.563 1.635,1.719 0.313,0.156 10 false *3 0.146,1.573 0.458,1.729 0.313,0.156 10 false *3
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper RH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper RH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):

488 to 492 mm (1.60 to 1.61 ft.)



c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps to the front drive shaft damper LH.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C304762

Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.


Hide 10.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY (for TMMT Made)

a.
C287114C01
0.688,1.323 0.688,1.552 false 1.698,1.521 1.698,1.75 false 2.49,1.667 2.49,1.896 false 2.896,1.25 2.896,1.479 false 0.635,1.583 0.948,1.74 0.313,0.156 10 false *1 1.646,1.781 1.958,1.938 0.313,0.156 10 false *2 2.438,1.917 2.75,2.073 0.313,0.156 10 false *3 2.844,1.5 3.156,1.656 0.313,0.156 10 false *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C295111C01
1.458,1.625 2.146,1.917 2.146,1.917 1.938,1.385 true 2.219,1.854 2.531,2.01 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Keep the tripod joint free of foreign matter.

·

Make sure to install the tripod joint in the correct direction.




f.
C392790

Using a snap ring expander, install a new front drive inner shaft inner shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard boot with grease.

Standard grease capacity:
for LH Side:

195 to 215 g (6.88 to 7.58 oz.)

for RH Side:

130 to 150 g (4.59 to 5.29 oz.)



h.
F045461C09
1.979,0.656 1.979,0.271 1.979,0.271 1.333,0.271 false 1.646,0.969 1.646,0.271 false 1.146,0.177 1.365,0.417 0.219,0.24 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 11.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY (for TMC Made)

a.
C287114C01
0.688,1.323 0.688,1.552 false 1.698,1.521 1.698,1.75 false 2.49,1.667 2.49,1.896 false 2.896,1.25 2.896,1.479 false 0.635,1.583 0.948,1.74 0.313,0.156 10 false *1 1.646,1.781 1.958,1.938 0.313,0.156 10 false *2 2.438,1.917 2.75,2.073 0.313,0.156 10 false *3 2.844,1.5 3.156,1.656 0.313,0.156 10 false *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C348433C02
1.76,1.5 2.26,2 2.26,2 1.271,1.844 false 2.292,1.917 2.604,2.073 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Keep the tripod joint free of foreign matter.

·

Make sure to install the tripod joint in the correct direction.




f.
C348431

Using a snap ring expander, install a new front drive inner shaft inner shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard boot with grease.

Standard grease capacity:

168 to 178 g (5.93 to 6.28 oz)



h.
C348434

Install the 3 rollers to the tripod joint.

NOTICE:
·

Make sure to install the rollers in the correct direction as shown in the illustration.

·

Do not drop the rollers.




i.
C160686C04
1.719,1.375 2.094,1.156 true 2.135,1.063 2.344,1.281 0.208,0.219 10 false *a
*a Groove


Install a new front axle inboard joint grommet to the front drive inboard joint assembly.

NOTICE:
·

Align the phase of the protrusions and depressions, and assemble the front axle inboard joint grommet to the front drive inboard joint assembly.

·

Make sure the protrusion on the inner corner of the front axle inboard joint grommet is securely inserted into the groove in the outer surface of the joint.




j.
C158439C18
1.385,1.24 1.125,0.458 1.125,0.458 1.927,0.667 true 0.948,0.365 1.344,0.521 0.396,0.156 10 *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 12.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C296188N07
1.438,1.656 1.906,1.896 0.469,0.24 10 false (A)

Check whether each drive shaft dimension (A) is within specification.

Dimension (A) (for TMMT made):
LH Side RH Side
590.5 mm (1.94 ft.) 887.2 mm (2.91 ft.)


Dimension (A) (for TMC made):
LH Side RH Side
591.2 mm (1.94 ft.) 895.2 mm (2.94 ft.)



Hide 43448F 13.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP (for TMMT Made)

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle inboard joint boot clamp onto the front axle inboard joint boot.


c.
C296175C06
1.74,1.396 2.104,1.708 2.104,1.708 2.729,1.708 true 2.781,1.625 3.24,1.823 0.458,0.198 10 false SST 2.917,0.115 3.229,0.313 0.313,0.198 10 false *a 1.635,0.458 1.948,0.656 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C195760E02
1.531,1.5 2.365,1.5 false 2.406,1.417 2.854,1.667 0.448,0.25 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43448F 14.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP (for TMC Made)

CAUTION:
C331975

·

When installing the front axle inboard joint boot clamp, do not perform the procedure without wearing protective gloves.

·

Performing the procedure without wearing protective gloves could result in injury.



a.
C107948

Install the front axle inboard joint boot clamp to the front axle inboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158356C19
2.469,0.938 2.771,1.219 0.302,0.281 10 false *a
*a Place the tip near the center of the lever


Using water pump pliers, pinch the front axle inboard joint boot clamp to temporarily secure it.


c.

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the front axle inboard joint boot.



Hide 43448G 15.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (for TMMT Made)

a.

Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.


b.
C298539C06
0.677,1.625 1.521,1.625 1.521,1.625 2.146,1.125 true 0.385,1.542 0.844,1.74 0.458,0.198 10 false SST 2.281,1.74 2.594,1.938 0.313,0.198 10 false *a 2.167,0.281 2.479,0.479 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C086270E20
1.896,0.792 3.021,0.813 true 3.083,0.729 3.406,0.885 0.323,0.156 10 false SST

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0472 to 0.1575 in.)


If the clearance is outside the specified range,retighten SST.


Hide 43448G 16.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (for TMC Made)

CAUTION:
C331975

·

When installing the front axle inboard joint boot clamp, do not perform the procedure without wearing protective gloves.

·

Performing the procedure without wearing protective gloves could result in injury.



a.

Install the front No. 2 axle inboard joint boot clamp to the drive shaft inboard joint boot groove.


b.
C268393C04
1.917,1.292 2.292,1.052 false 2.26,2.781 2.635,2.542 true 2.365,0.896 2.677,1.094 0.313,0.198 10 false *a 1.688,2 1.844,2.198 0.156,0.198 10 false A 2.688,3.708 2.844,3.906 0.156,0.198 10 false A 0.677,3.708 0.833,3.906 0.156,0.198 10 false A 2.656,2.406 2.969,2.604 0.313,0.198 10 false *b
*a Support Point
*b Indented Portion


Set the folding support point of the clamp so that it is aligned with any of the A portions indicated by arrows in the illustration.


c.
C415869C01
2.156,1.542 2.656,1.542 false 0.781,1.135 1.281,1.135 false 1.979,2.073 2.479,2.073 false 2.708,1.469 3.021,1.625 0.313,0.156 10 false *a 0.615,1.063 0.927,1.219 0.313,0.156 10 false *b 1.792,1.99 2.104,2.146 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




d.

As shown in the illustration, while pressing the inboard joint area against the work surface, firmly press the lever into place by rolling the inboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415870C01
3.615,1.104 3.365,1.698 3.365,1.698 3.719,1.083 true 2.083,1.49 1.594,1.49 true 5.927,2.219 5.76,1.917 5.76,1.917 5.531,1.917 true 1.885,2.292 1.604,2.292 1.604,2.292 1.365,1.875 true 3.823,0.302 4.135,0.458 0.313,0.156 10 false *a 4.073,1.333 4.385,1.49 0.313,0.156 10 false *b 5.219,0.698 5.531,0.854 0.313,0.156 10 false *c 3.25,1.719 3.563,1.875 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.406 1.74,1.563 0.313,0.156 10 false *d 5.354,1.844 5.667,2 0.313,0.156 10 false *d 1.938,2.25 2.25,2.406 0.313,0.156 10 false *e
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Make sure that the inboard joint is in direct contact with the work surface.

·

Do not damage the front drive shaft dust cover.




e.
C158764C05
1.802,3.719 1.115,4.375 1.115,4.375 1.615,3.698 true 0.979,4.365 1.292,4.563 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle inboard joint boot.