Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M20A-FXS) › from 2019.09
RM32K0E _52 Drivetrain _061224 DRIVE SHAFT / PROPELLER SHAFT _0405862 FRONT DRIVE SHAFT ASSEMBLY(for M20A-FXS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M20A-FXS)  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER

a.
C235587C09
0.635,0.323 0.948,0.604 false 0.448,1.063 0.74,1.313 false 0.469,0.208 0.781,0.365 0.313,0.156 10 false *a 0.135,0.948 0.594,1.146 0.458,0.198 10 false SST
*a Steel Plate


Using SST, a steel plate and a press, install a new front drive shaft dust cover.

SST
09527-10011  

NOTICE:
·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover.

·

Install the front drive shaft dust cover LH in the correct direction.




Hide 2.INSTALL FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

a.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard grease capacity:

115 to 125 g (4.06 to 4.41 oz)



d.

Install the front axle outboard joint boot into the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 3.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle outboard joint boot clamp onto the front axle outboard joint boot.


c.
C282247C01
2.156,1 2.531,0.76 false 2.563,0.667 3.021,0.865 0.458,0.198 10 false SST 1.677,0.021 1.99,0.177 0.313,0.156 10 false *a 2.552,1.573 2.865,1.729 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C282248E01
1.625,1.063 0.938,1.406 true 0.656,1.323 1.115,1.521 0.458,0.198 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43447E 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

a.

Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.


b.
C282249C01
2.219,1.281 2.76,1.073 false 2.802,0.979 3.26,1.177 0.458,0.198 10 false SST 1.781,0.042 2.094,0.198 0.313,0.156 10 false *a 2.49,1.792 2.802,1.948 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C282250E01
1.542,1.531 2.177,1.656 true 2.229,1.583 2.688,1.781 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43474E 5.INSTALL FRONT DRIVE SHAFT DAMPER LH

a.
C360105C04
0.219,1.625 0.219,1.292 false 0.75,1.719 0.75,1.385 false 1.333,1.625 1.333,1.292 false 2.271,1.813 2.271,1.479 false 2.188,1.865 2.5,2.021 0.313,0.156 10 false *1 0.677,1.771 0.99,1.927 0.313,0.156 10 false *2 0.146,1.667 0.458,1.823 0.313,0.156 10 false *3 1.25,1.677 1.563,1.833 0.313,0.156 10 false *3 1.708,0.271 2,0.479 0.292,0.208 10 false (A)
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper LH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper LH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):

161 to 165 mm (6.34 to 6.50 in.)



c.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.
C411296C03
1.594,1.073 1.229,0.51 1.229,0.51 1.125,0.51 true 0.771,0.427 1.083,0.583 0.313,0.156 10 false SST 2.688,1.844 3,2.042 0.313,0.198 10 true *a 1.813,0.146 2.125,0.344 0.313,0.198 10 true *b
*a Turn
*b Hold


Place SST onto the front drive shaft damper clamp, press it against the damper and slightly tighten SST.

SST
09521-24010  


e.

Tighten SST so that the front drive shaft damper clamp is pinched.

NOTICE:

Do not overtighten SST.



f.
C411297E02
0.479,1.635 1.073,1.24 true 0.146,1.573 0.604,1.771 0.458,0.198 10 false SST

Using SST, measure the clearance of the front drive shaft damper clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0590 in.)


If the clearance is not as specified, retighten SST.


Hide 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C411292C01
1.438,1.719 2.531,1.958 2.531,1.958 2.021,1.365 true 2.604,1.875 2.927,2.104 0.323,0.229 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Keep the tripod joint free of foreign matter.

·

Make sure to install the tripod joint in the correct direction.




f.
C411288

Using a snap ring expander, install a new front drive inner shaft inner shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard boot with grease.

Standard grease capacity:
for LH Side:

175 to 185 g (6.17 to 6.53 oz)

for RH Side:

175 to 185 g (6.17 to 6.53 oz)



h.
C411298C03
2.521,1.813 2.354,1.813 2.354,1.813 2.354,1.5 true 2.573,1.719 2.885,1.917 0.313,0.198 10 false *a
*a Groove


Install a new front axle inboard joint grommet to the inboard joint groove.

NOTICE:

Securely fit the protrusion on the front axle inboard joint grommet into the inboard joint groove.



i.
C411287C02
2.031,0.51 0.979,0.396 0.979,0.396 1.833,0.99 true 0.802,0.302 1.094,0.573 0.292,0.271 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C296188N07
1.438,1.656 1.906,1.896 0.469,0.24 10 false (A)

Check whether each drive shaft dimension (A) is within specification.

Dimension (A):
LH Side RH Side
594.2 mm (1.95 ft.) 898.4 mm (2.95 ft.)



Hide 43448F 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle inboard joint boot clamp onto the front axle inboard joint boot.


c.
C296175C07
0.635,0.75 1.073,0.75 1.073,0.75 1.615,1.281 true 0.323,0.656 0.781,0.854 0.458,0.198 10 false SST 2.938,0.125 3.25,0.323 0.313,0.198 10 false *a 1.604,0.51 1.917,0.708 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C195760E02
1.531,1.5 2.365,1.5 false 2.406,1.417 2.854,1.667 0.448,0.25 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0473 to 0.157 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.


b.
C298539E01
0.677,1.625 1.521,1.625 1.521,1.625 2.146,1.125 true 0.385,1.542 0.844,1.74 0.458,0.198 10 false SST

Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C086270E20
1.896,0.792 3.021,0.813 true 3.083,0.729 3.406,0.885 0.323,0.156 10 false SST

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

1.2 to 4.0 mm (0.0472 to 0.1575 in.)


If the clearance is outside the specified range, retighten SST.