Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300711 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1497  Communication Malfunction (Bus Ic)  


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1497 Communication Malfunction (Bus Ic)
Any of the following conditions is met:
·

Error in communication line

·

Open in communication line


·

Air conditioning harness assembly

·

No. 1 air conditioning radiator damper servo sub-assembly

·

Air conditioning amplifier assembly


Memorized
(10 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (READY) ○ ○
Malfunction Status Error in communication line ○ -
Open in communication line - ○
Detection Time 10 seconds or more 10 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

E357691E33
3.958,6.542 5.521,7.021 1.563,0.479 10 false Air Conditioning Harness Assembly 0.115,7.625 3.813,7.844 3.698,0.219 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly 0.802,9.438 3.01,9.865 2.208,0.427 10 false : LIN Communication Line 5.521,4.656 7.135,5.156 1.615,0.5 10 false Air Conditioning Amplifier Assembly 5.51,4.479 6.313,4.74 0.802,0.26 10 false f1*3, f5*4 5.646,3.635 6.198,3.885 0.552,0.25 10 false BUS 5.646,3.24 6.219,3.448 0.573,0.208 10 false BUSG 5.646,4.031 6.167,4.313 0.521,0.281 10 false BUSB 5.406,4.031 5.719,4.229 0.313,0.198 10 false 4 5.417,3.583 5.729,3.781 0.313,0.198 10 false 3 5.406,3.24 5.719,3.438 0.313,0.198 10 false 2 0.625,2.354 2.094,2.646 1.469,0.292 10 false Driver Side Air Mix*1 0.302,2.688 2.406,3.146 2.104,0.458 10 false Front Passenger Side Air Mix*2 0.75,4.438 1.906,4.719 1.156,0.281 10 false Mode Switching 0.25,6.542 2.354,7 2.104,0.458 10 false Front Passenger Side Air Mix*1 0.615,6.875 2.417,7.375 1.802,0.5 10 false Driver Side Air Mix*2 3.76,3.24 4.073,3.438 0.313,0.198 10 false 6 3.771,3.583 4.083,3.781 0.313,0.198 10 false 7 3.771,4.031 4.083,4.229 0.313,0.198 10 false 8 3.146,8.469 4.615,8.76 1.469,0.292 10 false *1: for LHD 3.146,8.771 4.615,9.063 1.469,0.292 10 false *2: for RHD 0.125,7.469 0.333,7.667 0.208,0.198 10 false f2 3.146,9.104 6.958,9.49 3.813,0.385 10 false *3: for TMMT Made HFQ-1234yf (R1234fy) Type or TMC Made 3.146,9.438 6.958,9.823 3.813,0.385 10 false *4: for TMMT Made HFC-134a (R134a) Type

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (AIR MIX SERVO TARG PULSE(D))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix) pulse Min.: 128
Max.: 383
for LHD:

Operates between 165 to 257 pulses


for RHD:

Operates between 255 to 347 pulses


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
OK:

No. 1 air conditioning radiator damper servo motor operates smoothly.



Result:
Result Proceed to
No. 1 air conditioning radiator damper servo motors are malfunctioning
(for TMMT Made HFQ-1234yf (R1234fy) Type or TMC Made)
A
No. 1 air conditioning radiator damper servo motors are malfunctioning
(for TMMT Made HFC-134a (R134a) Type)
B
No. 1 air conditioning radiator damper servo motors is normal C



A

2.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)

B

4.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)

C

6.CHECK FOR DTC
2.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)
NOTICE:

When inspecting the air conditioning amplifier assembly, do not bring the tester probes too close to each other as a short circuit may occur.


a.

Disconnect the f1 air conditioning amplifier assembly connector.


b.

Disconnect the f2 No. 1 air conditioning radiator damper servo sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f1-2 (BUSG) - f2-6 Always Below 1 Ω
f1-3 (BUS) - f2-7 Always Below 1 Ω
f1-4 (BUSB) - f2-8 Always Below 1 Ω
f1-3 (BUS) or f2-7 - Body ground Always 10 kΩ or higher
f1-4 (BUSB) or f2-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

3.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
NOTICE:

When inspecting the air conditioning amplifier assembly, do not bring the tester probes too close to each other as a short circuit may occur.


a.

Turn the power switch on (IG).


b.
E334625C50
2.865,0.417 3.198,0.625 0.333,0.208 2.573,2.271 3.094,1.24 true 2.26,2 3,1.24 true 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 2.99,0.438 3.302,0.635 0.313,0.198 10 false f1 0.417,3.938 0.875,4.135 0.458,0.198 10 false GND 2.094,2.031 2.552,2.229 0.458,0.198 10 false BUS 2.344,2.292 2.802,2.49 0.458,0.198 10 false BUSG
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Connect an oscilloscope to terminals f1-2 (BUSG) and f1-3 (BUS) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.


Item Content
Tool Setting 2 V/DIV., 2 ms./DIV.
Vehicle Condition Power switch on (IG)


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.INSPECT AIR CONDITIONING HARNESS ASSEMBLY (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY)
NOTICE:

When inspecting the air conditioning amplifier assembly, do not bring the tester probes too close to each other as a short circuit may occur.


a.

Disconnect the f5 air conditioning amplifier assembly connector.


b.

Disconnect the f2 No. 1 air conditioning radiator damper servo sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f5-2 (BUSG) - f2-6 Always Below 1 Ω
f5-3 (BUS) - f2-7 Always Below 1 Ω
f5-4 (BUSB) - f2-8 Always Below 1 Ω
f5-3 (BUS) or f2-7 - Body ground Always 10 kΩ or higher
f5-4 (BUSB) or f2-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY

5.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
NOTICE:

When inspecting the air conditioning amplifier assembly, do not bring the tester probes too close to each other as a short circuit may occur.


a.

Turn the power switch on (IG).


b.
E334625C49
2.865,0.417 3.198,0.625 0.333,0.208 2.573,2.271 3.094,1.24 true 2.26,2 3,1.24 true 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 2.99,0.438 3.302,0.635 0.313,0.198 10 false f5 0.417,3.938 0.875,4.135 0.458,0.198 10 false GND 2.094,2.031 2.552,2.229 0.458,0.198 10 false BUS 2.344,2.292 2.802,2.49 0.458,0.198 10 false BUSG
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Connect an oscilloscope to terminals f5-2 (BUSG) and f5-3 (BUS) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.


Item Content
Tool Setting 2 V/DIV., 2 ms./DIV.
Vehicle Condition Power switch on (IG)


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

6.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY